CS Paper Radar

Topology optimization of shipboard components for Navy shock certification via the Dynamic Design Analysis Method

Miguel A. Aguilo

cs.CE ·submitted 2026-10-19 23:03 UTC · v1
theory

Abstract

Shipboard equipment must survive the transient loads of underwater explosions. The U.S. Navy certifies such equipment with the Dynamic Design Analysis Method (DDAM), a modal response analysis driven by Navy shock design spectra. DDAM is well established as a verification tool, yet it is rarely used as a design driver in topology optimization. The design spectrum depends on the modal mass, a non-smooth coupling that classical sensitivity formulations do not address. This paper presents a complete differentiable formulation of the DDAM criterion for gradient-based topology optimization. Eigenvalue sensitivities follow the Fox-Kapoor method, and eigenvector sensitivities follow Nelson's method. The chain rule covers a spectral displacement that depends on both the natural frequency and the modal participation factor. Automatic differentiation assembles the sensitivity, and the engineer can certify components inside the optimization loop rather than after design. Three certification problems on a representative shipboard equipment frame demonstrate the workflow. In each, the optimizer removes 43.2% to 46.1% of the design-domain material and holds the certifying NRL Sum within 0.41% of the Navy allowable. Two companion studies follow. A compliance-optimized frame of nearly the same mass has a 5.2 Hz fundamental, outside the range the certification can qualify. Its nominal response also exceeds the allowable by a factor of 2.75. A lower bound on the mean of the two lowest eigenvalues separates the repeated pair that the demonstrations drive onto the frequency floor. The response then stops oscillating across the acceptance boundary. It ends at most 0.5% above the allowable, at a cost of under two percentage points of volume fraction.

Comment
32 pages, 17 figures, 12 tables

Closest papers

Nearest neighbours by meaning across the whole index.

Topology optimization with buckling constraints: Adaptive eigenvalue aggregation and modality identification

cs.CE ·2026-09-17 ·Badvelu Pranay Prabha, Prabhat Kumar
similarity 0.62
Abstract · 33 pages

This paper presents novel approaches to tackle two key challenges in topology optimization problems with buckling constraints: determining how many eigenvalues to aggregate and identifying the eigenvalue modality at the optimal design. We demonstrate the mathematical inconsistencies that arise when choosing an arbitrary fixed number of eigenvalues for aggregation. Specifically, if the multiplicity of the critical eigenvalues is smaller than the chosen subset size, coalescence with higher-order eigenvalues can occur. Neglecting these during aggregation causes incorrect sensitivities, while simply increasing the preselected eigenvalue count unnecessarily raises computational costs. To resolve this issue, we propose an approach that dynamically determines the exact number of eigenvalues required at each optimization iteration. The proposed approach reduces computation time significantly while maintaining competitive performance relative to the conventional method across the numerical experiments presented. Additionally, accurately predicting modality at the optimal point is crucial for understanding the buckled mode shapes of optimized designs. A new optimization formulation is proposed using the difference between eigenvalues to capture the true eigenvalue modality. This formulation is first validated on a classical 1D clamped column, successfully predicting both the bimodal solution and the optimal eigenvectors. The approach demonstrates that the optimal solutions for the wall reinforcement and shear-loaded hinged plate problems for the given set of parameters are trimodal and tetramodal, respectively.

0.27

Neural topology optimization of ship structures under propulsion machinery vibrations

cs.CE cs.AIcs.LGmath.NA+1 ·2026-09-29 ·Shengyu Yan, Muhammad Muztahidul Hakim Zareer, Jasmin Jelovica
similarity 0.59
Abstract · 24 pages, 13 figures, 7 tables

Ship structural vibrations contribute to noise, fatigue, and equipment damage, while dynamic-compliance topology optimization can produce pathological designs near resonance. This study extends neural-reparameterized topology optimization using a convolutional Kolmogorov-Arnold network (KATO) to forced-vibration design with active input power (AIP) as the objective. Applications include a 100 Hz engine-supporting deck panel and an 18 Hz thruster foundation frame. Helmholtz PDE filtering and Heaviside projection control feature sizes and manufacturing tolerance. Across both deck families, all eight optimized layouts reduce AIP relative to size-optimized references and, after finite-depth extrusion, also achieve lower static compliance. For unrestricted, manufacturing-aware, and stress-aware frame variants, KATO matches GCMMA in AIP within 0.5 dB while yielding 22-36x lower static compliance after matched-volume binary re-analysis. In a near-resonant 300 Hz case, both methods reduce initial AIP by more than 32 dB; KATO maintains a connected design, achieves 59x lower binary static compliance, and reduces maximum AIP over 1-500 Hz by 2.7 dB. KATO runs 6.4-10.4x faster than GCMMA for the implemented stress-aware formulations. The results demonstrate neural AIP-driven topology optimization as an efficient approach for designing connected, feature-size-controlled ship structures with improved forced-vibration performance.

0.30

Multi-Material Topology Optimization for Targeted Structural Dynamic Vibration Attenuation

cs.CE ·2026-10-22 ·Bir Bahadur Chaudhary, Bidhan Pandey, Bin Ouyang, Shiguang Deng
similarity 0.56
Abstract

Resonance-induced excessive vibrations can degrade performance, reduce reliability, and shorten the service life of engineering structures. To reduce the risk of resonance, structural natural frequencies are generally engineered to be shifted away from excitation frequencies. To achieve these frequency shifts, topology optimization provides a systematic approach to tailor structural stiffness and mass as an effective inverse design approach. Multi-material topology optimization exploits the high-dimensional design space of spatially varying material constituents by simultaneously optimizing material selection and spatial distribution over the design domain, offering great flexibility in controlling natural frequencies. This study proposes a multi-material topology optimization that attenuates excessive structural dynamic vibrations in free-vibration scenarios via a novel multivariate weight-based interpolation method. Additionally, to address non-smoothness due to mode switching amid optimization, we employ a bound formulation with an auxiliary scalar design variable to replace the max-min eigenvalue objective with constraints on individual eigenvalues. Furthermore, we study and compare three optimization formulations for multi-material design to attenuate vibrations, including maximizing fundamental eigenfrequency, maximizing the gap between adjacent eigenfrequencies, and excluding frequencies from targeted frequency bands, which are smoothly approximated by a proposed rational polynomial formulation. Numerical examples are presented to demonstrate the effectiveness and applicability of our proposed method.

0.30

Coordinating integration of multidisciplinary design analysis and optimisation codes with design structure matrices

cs.CE physics.comp-phcs.SE ·2026-11-17 ·W. J. Rutten, L. F. P. Etman, F. Warmer
similarity 0.56
Abstract · 18 pages, 5 figures, 9 tables. Submitted to Fusion Engineering and Design

The integrated analysis and optimisation codes used to design nuclear fusion reactors need to become increasingly large scale, multidisciplinary and complex to computationally verify design requirements more thoroughly and earlier in the design process. Though the manner in which the integrated models are coupled can have significant implications for computational efficiency, the structure of couplings typically remains hidden in the implementation of a design framework. As this problem is not unique to fusion, we frame integrated design problems as applications of the broader field of Multidisciplinary Design Analysis and Optimisation (MDAO). Originally developed for complex system design problems in e.g. aerospace, the MDAO field uses (extended) Design Structure Matrices (DSMs) to display the architecture of integrated analysis and optimisation codes. The aim of this work is to introduce these DSM methods and demonstrate how they can be used to improve the transparency and efficiency of design codes in fusion. As a proof of concept, DSM methods are applied to two case studies: stellarator optimisation with SIMSOPT and the PROCESS systems code. With these cases, we illustrate how a DSM can help identify structural assumptions in the code, and how architectural insight can be used to improve computational efficiency. In particular, we demonstrate the computational impact by modifying the PROCESS solver architecture based on the feedback loops revealed in an automatically generated DSM, yielding a significant reduction in model evaluations. Such architectural changes are considered especially impactful for future design frameworks that combine higher fidelity models with large numbers of inexpensive models.

0.33

Sensitivity Hot Spot Penalization: A Robust Topology Optimization Framework against First-Order Worst-Case Perturbations

cs.CE ·2026-08-31 ·Junpeng Wang, Niels Aage, Ole Sigmund
similarity 0.53
Abstract

Deterministic topology optimization can efficiently generate high-performance structural designs, but it does not explicitly control localized fragility induced by manufacturing variations and geometric uncertainties. Such fragility often appears as stress concentrations or hinge-like deformation mechanisms. Conventional robust topology optimization can suppress these features, but typically requires multiple design realizations and substantially increased computational cost. Recent work by Sigmund et al. (2026) introduced sensitivity hot spot penalization (SHoSP), which augments the nominal objective by a smooth maximum of its sensitivities and suppresses localized fragile features at low additional cost while promoting more even stress distributions. This paper establishes a general connection between SHoSP and a first-order worst-case robust approximation under a material-mass perturbation budget using a Taylor expansion and H{"o}lder's duality. The original penalty weight is identified as a dimensionless norm-bounded perturbation budget relative to the area (2D) or volume (3D) of the design domain. This interpretation explains the suppression of sensitivity hot spots, hinge localization, and stress concentrations by limiting the maximum first-order degradation under budgeted perturbations. It is investigated for compliance minimization and compliant mechanism design. Robustness is assessed using a relaxed worst-case density perturbation and by comparing deterministic and SHoSP designs under equivalent perturbation budgets. Stress-related effects observed on structured meshes are cross-validated by stress-oriented topology optimization and body-fitted finite element analyses. Extensions to porous infill optimization, multiple load cases, and large-scale 3D examples further demonstrate the applicability and superior scalability of the SHoSP framework.

0.22

Bilevel Optimization of Topology and Hyperparameters (BOTH)

cs.LG ·2026-09-18 ·Suryanarayanan Manoj Sanu, Miguel Anibal Bessa, Alejandro Marcos Aragón
similarity 0.48
Abstract · Currently under submission to SMO journal

Topology optimization (TO) represents a significant step towards automating the design process: given a working simulation, TO can produce a viable prototype at the press of a button by differentiating the simulation and iteratively improving the design. In practice, however, TO is riddled with ``magic numbers''---hyperparameters whose tuning significantly affects the outcome. Finding the right values typically requires not only deep problem-specific knowledge but also extensive trial-and-error. While practitioners can use surrogate-assisted hyperparameter optimization as an alternative, this approach requires strictly limiting the number of hyperparameters through careful problem formulation. Here, we propose differentiating TO itself using automatic differentiation. This yields ``hypergradients'' that allow us to tune these hyperparameters in tandem with the primary optimization. We show that evaluating just one or two steps of TO is sufficiently informative and that the method scales favorably to thousands of hyperparameters at an expense comparable to only a few standard TO runs. We demonstrate this approach on stress-constrained and compliance problems, with the latter utilizing a neural parameterization of the density field.

0.50

A Dynamic Aggregation Strategy Enhanced Efficient Global Optimization Algorithm for Solving High-Dimensional Turbomachinery Design Problems

cs.LG cs.CE ·2026-09-13 ·Qineng Wang, Zhendong Guo, Yun Chen, Guangjian Ma, Liming Song +1 more
publishedbenchmark similarity 0.48
Abstract · Author manuscript updated to align core methods and results with the published article; 37 pages, 14 figures, 11 tables

In order to solve the high-dimensional ($d \geq 30$) expensive black-box problems within budget, an efficient global optimization (EGO) algorithm with a dynamic aggregation strategy is proposed, labeled as DA-EGO. Specifically, the DA-EGO decomposes the original high-dimensional design space into a set of low-dimensional subspaces for efficient surrogate-based optimization search, and the optimal solutions of subspaces are combined as an elite point for the global search. Most importantly, the subspaces are not fixed. Instead, the subspace variables are updated in each iteration, according to the variable interaction analyses in the sub- and full-spaces. The perturbation method and the analysis of variance are used to detect variable interactions. To further accelerate the optimization progress, the searching ranges of subspaces are also adaptively adjusted according to the analyses of subspace optimization results of the previous iteration. Tests on 21 benchmark instances, comprising seven functions at 30, 60, and 90 dimensions, show that DA-EGO is effective on separable and partially separable problems under a budget of 1500 function evaluations. Its advantage is case-dependent: on the non-separable shifted Rosenbrock function, GSGA performs better at 60 and 90 dimensions, while the 30-dimensional results are statistically comparable to IKAEA and GSGA. Moreover, the advantage of DA-EGO is also seen in the aerodynamic optimization of a transonic rotor blade with 28 variables as well as the compressor stage optimization with 60 variables. With the above, the effectiveness of the proposed DA-EGO has been well demonstrated.

0.48

MiDShip: Multimodal Dataset of Ship Cargo Hold Structures for Engineering Design

cs.CE cs.LG ·2026-09-04 ·Noah J. Bagazinski, Md. Ferdous Alam, Jaya Manideep Rebbagondla, Faez Ahmed
similarity 0.47
Abstract

Ship structures govern vessel strength, safety, and manufacturability, but their design must satisfy hundreds of classification society requirements, making the process complex and iterative. Data-driven approaches are limited by the lack of structured datasets linking design geometry, structural performance, and rule-based constraints. This paper presents MiDShip, a multimodal dataset of 12,753 synthetic cargo-hold structural designs: 6,020 random, 496 generated by an SGLD-inspired procedure, and 6,237 generated by an equation-informed repair procedure. Each design includes parametric data, full and mesh-ready 3D geometry, engineering drawings and annotations, a bill of materials, and preliminary structural evaluations. Twenty-five constraints derived from a subset of ABS MVR are also evaluated. None of the random designs satisfies all constraints. Among the SGLD-inspired designs, 322 (64.9%) were fully compliant, with an average of 0.409 violations, 82.7% below the seed mean and 96.9% below the random-design mean. The repair procedure, developed through LLM-assisted code analysis, produced 4,952 fully compliant designs (79.4%), averaging 0.296 violations, 97.1% below the paired-source mean. In equal-size comparisons, mean nearest-neighbor distances in the scaled 120-parameter space were 3.495 for repaired designs, 1.144 for SGLD batches, and 3.729 for random designs. The primary contribution is the synchronized dataset and its generation and evaluation infrastructure; the generation studies demonstrate its utility rather than proposing new optimization algorithms. MiDShip supports machine learning, generative design, and automated rule-based evaluation for ship structures.

0.24