CS Paper Radar

Stiffness coefficients in granular micromechanics determined with three-point bending experiments and digital image correlation for a bimodulus material

Mohammad Mahdi Nayeban, Bilen Emek Abali, Reza Afshar, Francesco Fabbrocino, Anil Misra, Luca Placidi

cs.CE ·submitted 2026-10-27 09:00 UTC · v1
publishedunusual

Abstract

This study presents an inverse analysis to determine the stiffness parameters of a bimodulus constitutive model formulated within a granular micromechanics framework. Full-field normal strain measurements are obtained by Digital Image Correlation (DIC) during three-point bending tests and are used as experimental input to a hybrid numerical optimization procedure. The experimental campaign is designed to ensure that the measured strain fields remain within the elastic regime. Since the identification is formulated as a nonlinear regression problem, a physically informed initial parameter set is constructed to guide the optimization toward mechanically meaningful values. An initial estimate of the compressive stiffness is first obtained from the available manufacturer data. The tension-compression stiffness asymmetry is then estimated from the experimentally measured neutral-axis shift, which provides a macroscopic signature of bimodulus material behavior in bending. These estimates define the initial parameter set, which is subsequently refined through a hybrid optimization procedure based on the full-field comparison of the experimental and numerical normal strain distributions. The identified parameter set enables the numerical model to reproduce more closely both the through-depth profile and the spatial distribution of the normal strain component over the selected surface region. These results demonstrate that full-field normal strain measurements provide an effective basis for identifying the stiffness parameters of bimodulus granular micromechanics models. The largest differences between the numerical and experimental strain fields are observed near the load-application region, where localized strain variations are induced by the concentrated load.

Comment
Accepted for publication in Mathematics and Mechanics of Complex Systems (MEMOCS)

Closest papers

Nearest neighbours by meaning across the whole index.

Data-Driven Discovery of Composition-Dependent Constitutive Models for Hyperelasticity and Viscoelasticity of Digital Materials

cs.AI cond-mat.mtrl-scicond-mat.soft ·2026-09-03 ·Josué García-Ávila, Beijun Shen, Manuel K. Rausch, Mary C. Boyce, Adrián Buganza-Tepole
similarity 0.52
Abstract · 28 pages including references, 9 figures in the main manuscript. Supplementary material is available upon request from the corresponding aut…

Digital materials fabricated by multi-material 3D printing are designed as controlled mixtures of stiff and compliant constituents, yielding effective responses that span more than an order of magnitude in apparent stiffness and exhibit strongly nonlinear, composition-dependent, and rate-dependent dissipative behavior. Classical finite-strain viscoelastic models represent such behavior with closed-form strain energy functions for equilibrium and non-equilibrium stresses as well as evolution of internal variables, which may limit flexibility when a single constitutive model is expected to generalize across materials and loading rates. Here, we present a data-driven multi-material constitutive modeling framework that generalizes a formulation by Bergström and Boyce. The proposed framework retains the structure of the classical model, namely multiplicative kinematics, invariant-based strain-energy functions, and a scalar dissipative evolution law directed along the normalized nonequilibrium deviatoric stress. For the equilibrium branch, the data-driven discovery framework either directly predicts closed-form model parameters as functions of composition or automatically constructs a polyconvex strain-energy function using neural ordinary differential equations (NODEs). The nonequilibrium branch kinetics are learned similarly, either by directly identifying closed-form parameters across compositions or by using appropriately constrained artificial neural networks. Using multi-rate uniaxial compression data across multiple material compositions, we show that the proposed formulation captures rate-dependent stiffness and hysteresis across compositions while preserving thermodynamic consistency.

0.57

The norm, not the labels: training and evaluating finite-element surrogates for stress analysis in the energy norm

cs.CE cs.LG ·2026-11-09 ·Ruifeng Cao, Xidan Song
similarity 0.49
Abstract · 45 pages, 6 figures; supplementary material (37 pages, 4 figures) appended

Finite-element surrogates predict the stresses of a new design in one evaluation, but are usually trained on solutions with a displacement loss and compared by it, although engineering decisions rest on stresses. Application in engineering: stress analysis of perforated plates and solids with cavities, parametric families in which holes concentrate stress. Contribution to artificial intelligence: training and evaluating such surrogates in the energy norm, with or without solutions, and screening their predictions without solutions. For linear elastostatics, minimising the assembled discrete potential energy is exactly supervised regression in this norm: the energy gap of a prediction is the strain energy of its stress error. A displacement loss under-weights the stiff modes that carry the strains. In pre-registered comparisons, changing only the norm of the supervised loss cut a three-dimensional transformer's median energy-norm error 7.5-fold and its median von Mises error 6.1-fold; in two dimensions it more than halved the von Mises error, also on held-out instances. In three dimensions, the transformer trained on the energy alone came within a factor of 1.3 of the energy-norm-supervised one in median energy-norm and von Mises error. It was more accurate than the displacement-supervised one on all five metrics in every seed. Given the stiffness matrix, a Ritz projection was more accurate than the label-free transformer, in the seed means, on every metric but peak stress. No network transferred to a substantially finer mesh. The energy ranks predictions of a load case, and its sign flags those worse than the zero field.

0.47

A Differentiable Framework for Inverse Identification of Heterogeneous Cohesive Laws

cs.CE physics.comp-ph ·2026-10-24 ·Sida Hao, Jinkyo Han, Bahador Bahmani
similarity 0.48
Abstract

This work develops a differentiable finite element framework based on an intrinsic cohesive-zone formulation for identifying traction-separation laws from global force-displacement histories and spatially sparse strain measurements. The framework employs physics-constrained neural networks to represent flexible, thermodynamically structured cohesive laws, with sensitivities computed through automatic differentiation and a discrete adjoint that accounts for the history-dependent evolution of interfacial damage. To enable identification of spatially heterogeneous cohesive behavior, we extend learned constitutive priors to irreversible interfacial damage by constructing a shared, low-dimensional family of cohesive laws from representative traction-separation histories. This representation exploits common constitutive structure and parameter sharing to reduce the number of unknowns and regularize the inverse problem, while allowing local cohesive behavior to vary spatially through latent coordinates. Numerical investigations involving double-cantilever beams and fiber-matrix composites demonstrate that accurate reproduction of global force-displacement responses does not necessarily imply accurate recovery of the underlying cohesive laws. Incorporating spatially resolved strain measurements substantially improves constitutive identification, even when the admissible responses are constrained by a learned prior. Comparisons with conventional bilinear cohesive models and Bayesian optimization further illustrate the benefits of the learned constitutive representation and adjoint-based identification for high-dimensional inverse problems.

0.20

Knit-Structure Effects on Electromechanical Metrics and Their Correlation with Joint-Angle Estimation Error in Knitted Strain Sensors

cs.HC ·2026-10-05 ·Annika Eloranta, Zhuchenyang Liu, Iiro Naulapaa, Iida Arvola, Yao Zhang +3 more
similarity 0.48
Abstract · 10 pages

Knitted resistive strain sensors show strong promise for joint motion sensing in sports and rehabilitation, but the linkage between sensor design and in situ performance remains unclear. We investigate how knit structure and machine settings (e.g., stitch size) shape electromechanical properties and which metrics predict sensing performance during bending. Sensors spanning seven common knit structures at two stitch sizes were fabricated, characterized under uniaxial cyclic tension, and evaluated on a joint emulating bending rig. Joint-angle estimation was assessed with machine learning models, and correlations with electromechanical metrics were analyzed. Experimental results show that, among six common metrics, gauge factor and baseline resistance are largely set by knit structure, while working range, linear range, hysteresis, and cyclic stability vary only modestly across designs. Gauge factor correlates negatively and baseline resistance positively with joint-angle estimation error, mainly in lower-sensitivity designs, whereas the other metrics have weak or no predictive value. These results support using uniaxial tensile tests to screen out weak designs, while underscoring the need for joint-relevant evaluation and application-specific metrics to identify top performers.

0.40

A Gaussian Process State Space Formulation for Materials Constitutive Modeling: Application to Quasi-brittle Materials

cs.CE cs.LGmath.NAmath.PR ·2026-10-23 ·Houlin Xu, Chenyang Li, K. T. Ramesh, Michael D. Shields
similarity 0.47
Abstract

Constitutive models for history-dependent, path-dependent materials typically encode this dependence in prescribed functional forms through internal variables such as damage or plastic strain that are phenomenological, model-dependent, and not directly observable. These rigid forms lack flexibility to match observations, make calibration potentially non-unique, and complicate uncertainty quantification. This paper develops a Gaussian-process state-space model (GP-SSM) that replaces the fixed form of the constitutive model with a flexible GP regression, and the prescribed internal variables with latent state variables learned directly from observable stress-strain histories. As a GP, the model is naturally endowed with a measure of uncertainty and can be constrained to satisfy physical principles. We demonstrate this framework for quasi-brittle materials under triaxial compression, where the latent variable evolution is driven by the current-state stress invariants and the increment of equivalent strain to reflect irreversible, pressure-sensitive history. A sparse multi-output GP then maps the latent state and current strain tensor to the six-component stress response, trained by variational sparse inference. The trained model is exported into Abaqus/Explicit through a user material subroutine. Four verification cases are reported: (1) offline rollout on validation and test histories; (2) a single element under changing confinement; (3) a frozen-memory unloading-reloading extension; and (4) a multi-element structural model compared against the Karagozian and Case Concrete (KCC) model. These results show that the learned state-space update reproduces held-out RVE-scale histories in closed-loop rollout, tracks evolving confinement, supports unloading without violating the irreversibility of the learned history state, and reproduces structural-level behavior consistent with KCC.

0.24

History-Aware Force Sensing and Tunable Stiffness in a Pneumatic Kresling Origami Cell

cs.RO ·2026-11-01 ·Hengyi Zhou, Jiaqi Wang, Yilin Ma, Dezhong Tong, Xiaonan Huang
similarity 0.47
Abstract

Mechanical hysteresis and pneumatic loading complicate contact force estimation from deformation measurements in soft robots. This work presents a 3D-printed polyether block amide (PEBA) Kresling cell with magnetic angular sensing that supports three operating modes: force sensing at zero gauge pressure, force sensing with tunable stiffness under gauge positive pressure, and self-sensing actuation under negative gauge pressure. A multiscale gated recurrent unit (GRU) network estimates contact force from angular histories to account for the the combined effects of geometric deformation and material response. At zero gauge pressure, the model achieves a test RMSE of 0.76~N. Positive gauge pressure approximately doubles the average axial loading stiffness at +20~kPa over the first 3~mm of compression, while pressure-specific models maintain RMSEs below 0.93~N. Under negative gauge pressure, an energy-based compensation model enables contact force estimation using the the model trained at zero gauge pressure, achieving RMSEs of 1.66--2.10~N under quasi-static conditions. These results demonstrate a compact approach to combining force feedback, tunable axial stiffness, and self-sensing actuation in soft origami systems.

0.36

From Sparse AFM Observations to Probabilistic Macroscale Mechanics: A Generative-Physics Framework for Plant Cell Walls

cs.CE ·2026-10-05 ·Samundra Karki, Angona Biswas, Nabila Masud, Md Hasibul Hasan Hasib, Anwesha Sarkar +1 more
similarity 0.47
Abstract · 28 pages (16 main + 12 supplementary), 10 figures. Supplementary material (5 figures, 6 tables) included at the end

Nanoscale imaging of developing plant cell walls is expensive, and a limited number of atomic force microscopy (AFM) scans cannot capture the full structural variability of the wall. We present a generative-physics workflow that links sparse AFM observations of cotton (Gossypium hirsutum) fiber cell walls at 8 days post-anthesis (DPA) to distributions of effective elastic properties and a larger-scale mechanical response. We adapt a Stable Diffusion model with Low-Rank Adaptation (LoRA) to expand the experimental scans into an ensemble of AFM-like microstructures and assess the synthetic structures using microfibril crossover count and crossover angle. Each microstructure is mapped to spatially varying Young's modulus and Poisson's ratio fields and analyzed using strain-controlled finite element homogenization. Repeating this process across the image ensemble and a prescribed sweep of matrix-to-fibril stiffness ratios produces distributions of effective Young's modulus and Poisson's ratio. A single constitutive pair cannot capture this variation. The resulting distributions depend strongly on the matrix-to-fibril stiffness ratio and, in several cases, exhibit apparent multimodality. We further propagate the paired effective properties into 20 stochastic realizations of a tensile simulation of a larger specimen, yielding a distribution of macroscale stress response. The framework provides a probabilistic link between sparse nanoscale observations and continuum-scale mechanics while retaining variability across scales. The present results establish the computational workflow, while calibration of the intensity-to-property mapping against nanomechanical measurements remains necessary for quantitative prediction at the fiber scale.

0.31

Modelling the human-exoskeleton interaction interface - Benchmarking MuJoCo's deformable model

cs.RO ·2026-11-18 ·Lisette Masselink, Xiaolong Zhu Thomas George Thuruthel, Mohamed Irfan Refai
similarity 0.46
Abstract

The human-exoskeleton interaction interface, consisting of the exoskeleton attachment and the underlying human soft tissue, can affect the transfer of assistance. MuJoCo's \textit{flexcomp} has been previously used to model the soft tissue, but its accuracy has not been benchmarked against a finite element model. We benchmarked the \textit{flexcomp} Saint Venant-Kirchhoff (StVK) and Stable Neo-Hookean (SNH) models against COMSOL's Yeoh model in three cases: \textit{case 1}) spherical indentation, \textit{case 2}) compression, and \textit{case 3}) compression of a thigh. We compared force and strain energy as a function of indentation depth, hysteresis and computation time. MuJoCo's models capture force trends with a correlation of 0.97-0.99, but showed a stiffer response, which could be attributed to the volumetric locking of the linear finite elements. The MuJoCo models systematically underestimated hysteresis as MuJoCo's Rayleigh damping could not substitute a viscoelastic model. Moreover, MuJoCo's computational advantage was speed dependent: it was 2-2.5 times faster for spherical indentation, but COMSOL was faster for the other cases, which have more degrees of freedom and contacts. Although MuJoCo's \textit{flexcomp} offers a combination of soft-tissue modelling and multibody dynamics, the limitations regarding the stiffening and hysteresis should be addressed to be used for the analysis of the human-exoskeleton interaction interface.

0.26