CS Paper Radar

Rapid Heat Removal from Chip Cores: Near-Junction Active Cooling of Power Transistors via Electron Entropy Transport and Spatial Decoupling

Xiangying Li

eess.SY math-ph ·submitted 2026-11-09 00:25 UTC · v1
unusual

Abstract

Chip performance is limited by a shared bottleneck: the core produces heat faster than it can be moved out. We study the hardest case, RF power GaN HEMTs, whose hotspots exceed 5 kW/cm^2, and propose a horizontal near-junction active cooling topology built on electron entropy transport. Classical on-chip thermoelectric cooling faces a contest: Peltier absorption grows linearly with current, Joule heating with its square. In a vertical pillar, its own conduction resistance locks about half the Joule heat back toward the cold end, capping net cooling. From the Onsager framework we show the origin of this asymmetry: Peltier absorption localizes at the interface where the Seebeck coefficient jumps, whereas Joule heating fills the volume. The topology exploits this: a thermoelectric thin film lies flat on a diamond substrate beside the device drain (the electron exit), so bulk Joule heat leaves vertically into the substrate. A lateral fin model gives a closed form for the recirculation factor gamma: the vertical pillar yields gamma = 1, while the horizontal film yields gamma_max = sqrt(2) L_z/L_x, about 0.03 for L_z = 10 um, L_x = 500 um. The decoupling scales the net cooling ceiling and the critical runaway current by roughly 1/gamma. At equal resistance, the same film lifts maximum cooling from 13 mW to 500 mW, and the critical current from 0.65 A to 24 A. A time-constant and linear stability analysis with temperature-sensitive parameters defines the working window and safety margins for microsecond pulse cooling. The architecture leaves the device structure untouched; the principle, absorb at an interface and extract bulk heat vertically, applies to any chip with a hot core and offers a reproducible design path for near-junction thermal management.

Comment
10pages

Closest papers

Nearest neighbours by meaning across the whole index.

AI for Science with GPT-6 Astra: Thermal Design and Electrothermal Analysis of 2D CFET

cs.AI cond-mat.mtrl-scics.AR ·2026-09-15 ·Min-Hui Kim, Khushi Sharma, Sarah Zhang, Ye Wang
similarity 0.46
Abstract

Thermal optimization of 2D CFET inverters requires testing structural proposals against their electrical costs. We examine these research tasks using an AI agent workflow within a supplied electrothermal model. At 12 nm, Astra selects a redistributed source-interconnect geometry, while a coordinating agent proposes a substrate-directed heat-removal path. The combined design reduces peak temperature rise by 1.67 K at fixed metal volume and 20 μW. A subsequent metal-resistance sensitivity gives about 0.6-K inverter cooling alongside a 2% nFET on-current loss. Effective contact-length scaling further shows that lower temperature can accompany higher thermal resistance when current falls. Reproduction identifies agreeing implementations and retains a 104.95-K failure for diagnosis. These results show that an AI scientist workflow can propose thermal structures, test them under common constraints, and quantify their electrical cost.

0.35

Asymmetric Transistor Aging Under Thermal Gradients

eess.SY ·2026-11-18 ·Alex Grinshpun, Firas Ramadan, Freddy Gabbay
published similarity 0.44
Abstract · Accepted for publication at ICSEE 2026

Advanced technology nodes improve performance but increase susceptibility to BTI-induced aging. Using aging- aware circuit simulations, we show that realistic on-chip thermal gradients can cause significant asymmetric transistor degradation in 16 nm FinFET circuits, leading to setup and hold time violations. These results highlight the necessity of incorporating thermal-gradient-aware aging analysis into timing signoff to ensure chip reliability.

0.32

Design Space Exploration of Backside Clock Meshes for 2 nm GAAFET BSPDN Technology

cs.AR ·2026-10-01 ·Wajid Ali, Muhammad Hadir Khan, Dalton Gaddy, Matthew Guthaus
similarity 0.44
Abstract

Clock meshes are used in high-performance VLSI designs to minimize skew and tolerate on-chip variation, but they spend scarce routing resources on premium metal layers. Backside power delivery creates a new option: it adds thick, low-resistance metal layers on the back of the wafer, and the power grid does not consume all of them. Flip-flops remain on the frontside; a backside mesh therefore cannot drive them directly, and every connection passes through a through-silicon via. We present the first design-space exploration of backside clock meshes, implemented in OpenROAD on GT2N, a 2 nm nanosheet technology. Four benchmarks (1,938 to 15,311 flip-flops) are explored with multi-objective Bayesian optimization, and every design point is verified by transistor-level SPICE simulation, since the cyclic mesh cannot be evaluated by static timing analysis. Across all four designs, the backside mesh consistently outperforms an identical frontside mesh, with on average 45% lower skew, 25% lower sink slew, 4.5% lower power, and 28% less frontside clock wiring, and its skew spread under 10,000-sample Monte Carlo is a third of the frontside mesh's.

0.28

System-Technology Co-Evaluation of A7 CFET and A10 NSFET Technologies from Cell Parasitics to Chip Reliability

cs.ET ·2026-09-14 ·Mahdi Benkhelifa, Leon Mayr, Hadi Nour Eddine, Andrea Padovani, Luca Larcher +1 more
similarity 0.44
Abstract

Complementary FETs (CFETs) extend nanosheet FET (NSFET) scaling by vertically stacking n- and p-type gate-all-around (GAA) devices, thereby shrinking standard-cell area. The performance gain, however, cannot be assessed from device metrics alone, as CFET layouts also introduce larger cell-level parasitic resistance and capacitance (RC). In this work, we present a physics-based thermal- and aging-aware system-technology co-evaluation (STCO) flow to assess parasitic RCs in A7 CFET and A10 NSFET technology nodes. Our flow links calibrated device models, optimized standard-cell generation, automated GDS-to-TCAD conversion enabling accurate 3D parasitic RC extraction, full RTL-to-GDS implementation for an AI accelerator, multiphysics thermal analysis, and physics-based bias temperature instability (BTI) aging evaluation. Using the same device model for both technologies, we can isolate the impact of parasitic RCs and design at different levels of the design flow. The results of the AI accelerator design demonstrate that the A7 CFET reduces the chip area by 24.7% and the total wire length by 12%, improving the area efficiency TOPS/mm^2 by 74% relative to the baseline of the A10 NSFET. Under iso-frequency operation, results reveal that CFET voltage scaling reduces power by 68% and lowers power density from 148 W/cm^2 to 55 W/cm^2, which reduces the chip's temperature from 125 degrees C down to merely 62 degrees C. The resulting reduction in stress temperature suppresses 10-year BTI-induced degradation by 39%, reducing the required aging timing guardband by 53%.

0.34

Beyond HBM-on-GPU: Thermal Design Envelope for 3D Volumetric DRAM-on-GPU Integration

cs.ET ·2026-09-21 ·Yukai Chen, Melina Lofrano, Khakim Akhunov, Jonas Svedas, Arjun Singh +10 more
published similarity 0.43
Abstract · Presented at the 52nd IEEE European Solid-State Electronics Research Conference (ESSERC 2026), Palma de Mallorca, Spain, September 7-10, 202…

The scaling of GPUs for AI and HPC workloads is increasingly constrained by the capacity, bandwidth, and thermal limits of both 2.5D HBM-GPU and direct-stacked 3D HBM-on-GPU integration. This work establishes the thermal design envelope for 3D volumetric DRAM-on-GPU integration, in which vertically oriented DRAM dies and interleaved cooling cavities reshape heat flow and memory interfacing above the GPU. Using a package-level thermal model anchored to a consistent HBM-on-GPU baseline and driven by a realistic reticle-scale non-uniform GPU power map, we quantify the key parameters governing thermal feasibility. Stack height is the dominant limiter of peak temperature, while cooling-cavity conductivity shifts the feasible region, and mold insertion and stack orientation further modulate thermal behavior. A distributed memory-controller and network-on-chip tier introduces only a moderate thermal penalty. Although die-level parallelism increases bandwidth, the reduction in simulated training time saturates once execution becomes compute-bound. These results define a bounded co-design space across bandwidth, capacity, and thermal constraints for 3D volumetric DRAM-on-GPU integration.

0.38

EGGPlacer: Energy-Guided Generative Chip Placement with Diffusion Models

cs.AR cs.AI ·2026-10-22 ·Qi Zhou, Guojun Liu, Juanhong Zhao, Guangzhi Qi, Zehao Chen +1 more
similarity 0.43
Abstract · 27 pages, 9 figures, 11 tables. Preprint

Chip placement strongly affects routed wirelength and thermal behavior, yet these downstream metrics are difficult to evaluate during macro placement. Learning-based macro placers commonly optimize the macro-only half-perimeter wirelength (HPWL), denoted mHPWL, which ignores standard cell connectivity and spatial demand. In contrast, analytical mixed-size placers optimize differentiable full netlist wirelength and density objectives but are typically unaware of thermal effects. We propose EGGPlacer, an energy-guided diffusion framework that incorporates analytical placement feedback and thermal feedback into macro placement generation. An analytical placer acts as an online physical response model, exposing the standard cell distribution and a full netlist wirelength proxy induced by each intermediate macro placement, while a differentiable thermal model provides temperature feedback. These signals are formulated as composable energies and injected throughout reverse diffusion without retraining the underlying generative model. Experiments on public placement benchmarks show that EGGPlacer achieves competitive mixed-size HPWL relative to strong analytical and learning-based macro placers. In the end-to-end evaluation, EGGPlacer also obtains the lowest average routed wirelength and peak temperature among the evaluated methods. Ablation studies further demonstrate that analytical and thermal guidance provide distinct and complementary benefits across wirelength proxies, routed wirelength, and thermal objectives.

0.29

The conductance filtration: sink-relative persistence and exact edge sensitivity for heat transport in particle-filled composites

cs.CE cond-mat.mtrl-scicond-mat.dis-nn ·2026-09-25 ·Daisuke Yasufuku
unusual similarity 0.43
Abstract · 45 pages, 15 figures. Japanese-language version: https://doi.org/10.5281/zenodo.22760047

We formulate the thermal conductance $g_e$ of a particle pair as three branch types -- contact, near-contact and bond -- within a single construction, and we introduce the filtration that takes this $g_e$ as its axis (the conductance filtration) together with persistence taken relative to the sink boundary. We then show that the dissipation share is exactly the logarithmic sensitivity of the effective conductance, and that a finite change of a single edge is predicted exactly in closed form. The allocation of the dissipation among branch types, and the idealisation ratio of each mechanism (interface, matrix and particle), are thereby obtained as diagnostic quantities on one and the same graph representation.

0.41

TherMosaic: Accelerating Perceived Thermal Transitions Through Spatiotemporal Thermal Feedback

cs.HC ·2026-09-04 ·Zining Zhang, Jiasheng Li, Myungin Lee, Zeyu Yan, Jin Ryong Kim +1 more
top venuehighly cited similarity 0.43
Abstract

Thermal feedback can enrich immersive interaction, but thermoelectric devices often change temperature too slowly to match interactive timing. We present TherMosaic, a spatiotemporal thermal feedback approach that accelerates perceived temperature transitions by leveraging two perceptual mechanisms: spatial summation and thermal adaptation. Focusing on the fingertip, we first investigate this approach using a custom 2*2 array of independently controlled Peltier modules. Across three controlled perceptual studies, we show that distributed thermal stimulation can preserve stable hot and cold percepts despite local deviations, that adaptation helps maintain these percepts during changing stimulation, and that combining these effects reduces perceived transition time by about 30%-40% for transitions originating from hot or cold states. We then translate the same design principles into a standalone wearable implementation of TherMosaic and evaluate it in virtual reality. Our results show that this approach reduces perceived thermal lag and improves temporal alignment between thermal and visual events in interactive use.

0.69