CS Paper Radar

System-Technology Co-Evaluation of A7 CFET and A10 NSFET Technologies from Cell Parasitics to Chip Reliability

Mahdi Benkhelifa, Leon Mayr, Hadi Nour Eddine, Andrea Padovani, Luca Larcher, Hussam Amrouch

cs.ET ·submitted 2026-09-14 10:16 UTC · v1

Abstract

Complementary FETs (CFETs) extend nanosheet FET (NSFET) scaling by vertically stacking n- and p-type gate-all-around (GAA) devices, thereby shrinking standard-cell area. The performance gain, however, cannot be assessed from device metrics alone, as CFET layouts also introduce larger cell-level parasitic resistance and capacitance (RC). In this work, we present a physics-based thermal- and aging-aware system-technology co-evaluation (STCO) flow to assess parasitic RCs in A7 CFET and A10 NSFET technology nodes. Our flow links calibrated device models, optimized standard-cell generation, automated GDS-to-TCAD conversion enabling accurate 3D parasitic RC extraction, full RTL-to-GDS implementation for an AI accelerator, multiphysics thermal analysis, and physics-based bias temperature instability (BTI) aging evaluation. Using the same device model for both technologies, we can isolate the impact of parasitic RCs and design at different levels of the design flow. The results of the AI accelerator design demonstrate that the A7 CFET reduces the chip area by 24.7% and the total wire length by 12%, improving the area efficiency TOPS/mm^2 by 74% relative to the baseline of the A10 NSFET. Under iso-frequency operation, results reveal that CFET voltage scaling reduces power by 68% and lowers power density from 148 W/cm^2 to 55 W/cm^2, which reduces the chip's temperature from 125 degrees C down to merely 62 degrees C. The resulting reduction in stress temperature suppresses 10-year BTI-induced degradation by 39%, reducing the required aging timing guardband by 53%.

Closest papers

Nearest neighbours by meaning across the whole index.

Asymmetric Transistor Aging Under Thermal Gradients

eess.SY ·2026-11-18 ·Alex Grinshpun, Firas Ramadan, Freddy Gabbay
published similarity 0.66
Abstract · Accepted for publication at ICSEE 2026

Advanced technology nodes improve performance but increase susceptibility to BTI-induced aging. Using aging- aware circuit simulations, we show that realistic on-chip thermal gradients can cause significant asymmetric transistor degradation in 16 nm FinFET circuits, leading to setup and hold time violations. These results highlight the necessity of incorporating thermal-gradient-aware aging analysis into timing signoff to ensure chip reliability.

0.32

Breaking the Myth of Four-Tier Stacked Transistors for Logic: an Investigation from Process to Device and Block-Level PPA

cs.ET cond-mat.mes-hall ·2026-11-18 ·Jianxiang Jin, Haoran Lu, Yihan Luo, Yanbang Chu, Yibo Zhang +11 more
similarity 0.60
Abstract · 4 pages,17 figures,conference

For the first time, this work evaluated whether 4-tier stacked transistors can translate the straightforward density gains into realistic chip-level scaling benefits. A practical dual-sided 4-tier transistor-stacking CFFET (Flipped CFET-to-CFET) process was proposed, on which a DTCO framework spanning standard-cell design, local interconnects, RO analysis, and physical implementation was built under 2A node design rules. The CFFET was also benchmarked with its 2-tier transistor-stacking counterparts FFET. Among CFFET configurations, the best-performing Symmetric Power still lags FFET by 11.2% in RO frequency due to the complex MOL parasitics. At the block level, CFFET reduces the Ibex RISC-V core area by only 12.8% (far below the 40% nominal cell-height reduction), while running 10.9% slower at iso-power. We further introduced a novel Tetris-like cell stitching to minimize the area overhead, which allows non-rectangular cell design and recovers 7.4% area in a 1-bit ALU design. An optimized NanoStack CFFET was finally proposed, inspired by previous work. This work indicates that straightforward vertical 4-tier stacking proves insufficient to guarantee enough PPA benefits, though the resulting design insights may guide future advanced architectures.

0.23

Design Space Exploration of Backside Clock Meshes for 2 nm GAAFET BSPDN Technology

cs.AR ·2026-10-01 ·Wajid Ali, Muhammad Hadir Khan, Dalton Gaddy, Matthew Guthaus
similarity 0.56
Abstract

Clock meshes are used in high-performance VLSI designs to minimize skew and tolerate on-chip variation, but they spend scarce routing resources on premium metal layers. Backside power delivery creates a new option: it adds thick, low-resistance metal layers on the back of the wafer, and the power grid does not consume all of them. Flip-flops remain on the frontside; a backside mesh therefore cannot drive them directly, and every connection passes through a through-silicon via. We present the first design-space exploration of backside clock meshes, implemented in OpenROAD on GT2N, a 2 nm nanosheet technology. Four benchmarks (1,938 to 15,311 flip-flops) are explored with multi-objective Bayesian optimization, and every design point is verified by transistor-level SPICE simulation, since the cyclic mesh cannot be evaluated by static timing analysis. Across all four designs, the backside mesh consistently outperforms an identical frontside mesh, with on average 45% lower skew, 25% lower sink slew, 4.5% lower power, and 28% less frontside clock wiring, and its skew spread under 10,000-sample Monte Carlo is a third of the frontside mesh's.

0.28

AI for Science with GPT-6 Astra: Thermal Design and Electrothermal Analysis of 2D CFET

cs.AI cond-mat.mtrl-scics.AR ·2026-09-15 ·Min-Hui Kim, Khushi Sharma, Sarah Zhang, Ye Wang
similarity 0.56
Abstract

Thermal optimization of 2D CFET inverters requires testing structural proposals against their electrical costs. We examine these research tasks using an AI agent workflow within a supplied electrothermal model. At 12 nm, Astra selects a redistributed source-interconnect geometry, while a coordinating agent proposes a substrate-directed heat-removal path. The combined design reduces peak temperature rise by 1.67 K at fixed metal volume and 20 μW. A subsequent metal-resistance sensitivity gives about 0.6-K inverter cooling alongside a 2% nFET on-current loss. Effective contact-length scaling further shows that lower temperature can accompany higher thermal resistance when current falls. Reproduction identifies agreeing implementations and retains a 104.95-K failure for diagnosis. These results show that an AI scientist workflow can propose thermal structures, test them under common constraints, and quantify their electrical cost.

0.35

NN-Based Transistor Modeling for Ultra-Fast SPICE Simulation and Standard Cell Library Characterization

cs.ET cs.LG ·2026-10-22 ·Rodion Novkin, Hussam Amrouch
benchmark similarity 0.55
Abstract · 11 pages

Neural network (NN)-based transistor models have proven to be a promising solution to accelerate device modeling. Although these models demonstrated remarkable speedup in circuit simulations, they were not rigorously tested in complex tasks within standard EDA tool flows for chip design, which require very high transistor model precision to provide accurate results and converge properly. To investigate their full potential and promise, we develop NN-based transistor models that accurately predict the drain current and various charges for a 3nm nanosheet, and employ the models for a standard cell library characterization. This enables us to evaluate the accuracy and speedup under a very wide range of SPICE simulations, benchmarking our models against an industry-standard implementation. Since standard cell library characterization involves thousands of SPICE simulations, it serves as a great benchmark for transistor model quality and consistency. To further evaluate model accuracy, we also perform analog- and digital-level simulations for various complex circuits. Our experiments reveal that NN-based models are a valid alternative to existing transistor compact models, capable of producing accurate delay and power estimates with a much higher speed and convergence time compared to the conventional Verilog-A-based industry-standard (BSIM-CMG) transistor compact model. Our NNs achieve sub-0.11% and 0.76% errors for delay and total power evaluation on a wide range of circuits, while taking up to 8 times less time during the standard cell library characterization. Additionally, we provide comprehensive information and guidance on NN accuracy, unveiling the relationship between NN size and its effect on circuit simulation precision.

0.35

A Composable AI-Accelerated Iterative Solver for 3D-IC Thermal Modeling

cs.LG ·2026-10-01 ·Yixing Li, Jiahang Zhou, Zhiyu Zeng, Xin Ai
similarity 0.55
Abstract

Accurate thermal analysis of heterogeneous 2.5D/3D-IC packages is essential yet computationally prohibitive. A single full-package FEM simulation can take hours, while AI-based surrogates treat the entire stack as a monolithic prediction target and must be retrained whenever the die count or topology changes. To address this limitation, this work proposes Domain-Decomposed AI-Accelerated Iterative Solver for Thermal Analysis (DAIST), a composable thermal solver that decomposes the global package simulation into block-level subdomain problems, replaces subdomain solvers with neural operators, and couples them through iterative exchanges of interfacial temperature and heat flux. This local-to-global architecture eliminates the topology lock-in of monolithic models: block-level neural operators can be directly reused in unseen package assemblies without retraining. The iterative coupling strategy further provides a controllable accuracy-runtime tradeoff, where the iteration budget can be adjusted to trade accuracy for runtime. Evaluated on a multi-chiplet system and an advanced packaging system, DAIST achieves up to $178\times$ speedup over traditional FEM solvers with mean temperature errors of 0.068% and 0.323%, respectively, while demonstrating cross-topology reuse of block-level models across structurally distinct package assemblies.

0.06

IC-ThermBench: An Open, Progressive Benchmark for Generalizable 2.5D/3D-IC Thermal Learning

cs.CE ·2026-08-25 ·David Hang, Wenkai Yang, Kuiye Ding, Haiyang Xin, Jacky Wei
benchmarkcode/data similarity 0.53
Abstract · Project site: https://github.com/Day333/ThermalBench

Standardized benchmarks are fundamental to reliable progress in AI for EDA, including learning-based thermal modeling. However, existing thermal prediction studies often rely on different datasets, simulators, data splits, preprocessing pipelines, and metrics, while most datasets and implementations remain unavailable, making fair and reproducible comparison difficult. We introduce IC-ThermBench, an open and progressive benchmark that combines established 3D-IC steady-state, transient, and industrial package tasks with a new 50,000-sample 2.5D chiplet extension designed to evaluate progressively broader represented physical variation and cross-package OOD transfer. Five Generalization Scopes cover 3D-IC fixed-design prediction, Within-Family Generalization under layout, material, and boundary-condition variation, and Cross-Package OOD transfer to unseen package systems. We evaluate eight representative baselines under common data, splits, labels, and metrics. Performance degrades gradually from S2 to S4 as represented physical support broadens, but Cross-Package OOD produces a much sharper degradation: the best RMSE and MAE increase from 1.216 and 0.938~K at S4 to 15.99 and 15.00~K at S5, respectively. With only 10 labeled samples per OOD case, target-domain adaptation reduces the best MAE to 2.60~K. IC-ThermBench further provides a unified generation, training, inference, and evaluation pipeline, enabling reproducible and fair comparison of existing and new thermal predictor.

0.32

A Process-Aware Hybrid Si/IGO Monolithic-3D 6T SRAM with BEOL Pass-Gates for the 2nm Node

cs.AR cs.ET ·2026-08-24 ·Po-Chuan Wang, Dongwon Jang, Eknath Sarkar, Alexei Svizhenko, Md. Nahid Haque Shazon +3 more
similarity 0.53
Abstract

We propose a monolithic-3D (M3D) 6T SRAM at the 2nm node, integrating BEOL IGO pass-gates (PGs) with an all-silicon nanosheet latch, buried power rails (BPRs), and Ru interconnects. TCAD calibrated to a state-of-the-art double-gate IGO transistor with a tri-layer HfO$_2$/ZrO$_2$/HfO$_2$ (HZH) gate stack is combined with virtual fabrication and 3D parasitic extraction to realize the first process-aware layout of this topology. A novel neighbor-cell shared source/drain (S/D) bitline (BL) design enlarges the IGO contact area to mitigate contact resistance and restore PG drive without area penalty. The resulting cell achieves a 25\% footprint reduction vs the high-performance (HP) 122 Si baseline while maintaining robust static noise margin (SNM) over a wide supply voltage range. At the 128$\times$256 subarray-level, it reduces write delay by 42.2\% and EDP by 9.7\% compared to the high-density (HD) 111 Si baseline, owing to reduced cell parasitics and wordline (WL) loading from the smaller footprint.

0.27