CS Paper Radar

Interference-Aware Tone Selection for Bluetooth Channel Sounding

Taewoo Kim, Vishrant Tripathi

cs.NI ·submitted 2026-11-17 20:22 UTC · v1

Abstract

Bluetooth Channel Sounding enables distance estimation using phase measurements across multiple frequencies. However, coexistence with Wi-Fi and other 2.4 GHz radios can fragment the available frequency band, making reliable ranging difficult when only a limited number of tones can be selected. Drawing on sparse antenna-array theory, we show that interference avoidance alone is insufficient: the spacing of selected tones can introduce repeated peaks in the ranging response, leading to estimation errors. We propose a lightweight, interference-aware tone-selection method that jointly considers frequency occupancy, tone spacing, and frequency span. Our method constructs a 15-tone map using a three-step rule without ranging measurements, ground-truth distance, or online candidate-map search. We evaluate the method using simulations of 900 indoor environments, a public Bluetooth Channel Sounding dataset, and measurements from commercial Nordic nRF54L15 hardware. Compared with random interference avoiding baseline, our proposed method improves ranging success percentage by 39 points under mixed interference, 29 points on the public dataset, and 82 points in hardware experiments. These results demonstrate the importance of tone selection for practical Bluetooth Channel Sounding.

Closest papers

Nearest neighbours by meaning across the whole index.

Channel Modeling for Phase-Based Ranging

eess.SP ·2026-08-18 ·Till Droemmer, Markus Gardill
similarity 0.70
Abstract · 4 pages, 4 figures. Submitted to IEEE Radio and Wireless Week (RWW) 2027

This paper presents a Python-based simulation framework for the physical layer of Bluetooth Channel Sounding in accordance with Bluetooth Core Specification v6.2. The simulator implements Mode 3 phase-based ranging across 72 active tones in the 2.4 GHz ISM band and supports multiple propagation conditions, including free-space, static multipath, and IEEE 802.15.4a stochastic multipath channels. In addition, it models relevant hardware and interference effects such as phase noise, phase ramp, carrier frequency offset, IQ imbalance, ADC quantization, and narrowband interference from co-located Wi-Fi systems, with parameters derived from commercial SoC datasheets and field measurements. The framework enables controlled and repeatable analysis of physical layer effects that are difficult to isolate in over-the-air experiments and are not sufficiently represented in existing higher-level simulation tools. This work focuses exclusively on physical layer signal generation, channel modeling, and impairment injection, providing a foundation for future studies on Bluetooth Channel Sounding ranging and localization algorithms.

0.28

Scalable BLE Channel Sounding Localization with Ranging-Assisted PDoA

eess.SP cs.NI ·2026-11-06 ·Jorg Wieme, Eli De Poorter, Jeroen Hoebeke
code/data similarity 0.65
Abstract · 14 pages, 5 figures, 7 tables, Appendix, For reproducibility code available at https://gitlab.ilabt.imec.be/iwine/ra-pdoa-simulator

Bluetooth Channel Sounding (CS) enables accurate phase-based ranging, but multi-anchor localization requires sequential ranging exchanges that limit scalability and increase measurement latency. This paper proposes Ranging-Assisted Phase Difference of Arrival (RA-PDoA), a scalable BLE localization architecture combining one active anchor performing a standard two-way CS exchange with multiple passive receive-only anchors observing the same transmissions. A channel-recovery framework is derived that enables passive anchors to reconstruct a channel response suitable for super-resolution delay estimation, allowing multipath-robust ranging without participating in a two-way exchange. Coarse arrival-time information is further used to bound the position estimate and reject inconsistent range solutions. A comprehensive evaluation characterizes the impact of multipath propagation, body shadowing, synchronization requirements, oscillator impairments, anchor placement, and deployment inaccuracies, thereby quantifying the practical infrastructure requirements for scalable BLE localization. Simulation results in modeled indoor environments show that RA-PDoA reduces the 90th-percentile localization error from 175.3 cm to 95.5 cm under body shadowing while maintaining an airtime requirement independent of the number of anchors. The results demonstrate that a single active ranging link enables scalable and multipath-robust BLE Channel Sounding localization.

0.30

Retrospective Evaluation of Bluetooth RSSI Fingerprinting for Bin Localization on an Industrial Shop Floor

cs.NI ·2026-10-15 ·Saif Lakhani
similarity 0.60
Abstract · 2 figures, 1 CSV

This paper evaluates an archival Bluetooth Low Energy received signal strength indicator (RSSI) dataset collected for bin localization on an industrial shop floor. The installation used 24 fixed relays positioned on walls and Bluetooth beacons attached to bins, with each relay applying a Kalman filter to its own readings in firmware before publishing them. The primary survey produced 19,034 usable two-minute fingerprint samples across 90 known positions, with 23 relay measurements available as model features. We compare calibrated path-loss multilateration with two radio-map estimators: distance-weighted $k$-nearest neighbours and Random Forest regression. A random 70/30 row split measures recognition at surveyed positions, while a coordinate-grouped split reserves 27 entire positions for testing and measures interpolation to unseen positions. Random Forest achieved a median error of 0.66~m for surveyed positions, with 77.9% of estimates within 3~m and 96.3% within 10~m. For unseen positions, median error increased to 9.42~m and 55.5% of estimates were within 10~m. Path-loss multilateration produced a 19.41~m median error on unseen positions, close to the 19.62~m mean-position baseline. The results support RSSI fingerprinting for a fixed inventory of surveyed bin positions, but not precise continuous localization between survey points. Git history dates the original implementation to September 7, 2019. The evaluation code in this paper was written in October 2026 and is reported separately from the seven-year-old prototype.

0.24

Analyzing and Characterizing Multi-Source Interference Effects at Jammertest Norway 2025

eess.SP ·2026-08-16 ·Lucas Heublein, Inigo Cortes Vidal, Tobias Feigl, Alexander Rügamer, Felix Ott
publishedbenchmark similarity 0.58
Abstract · 15 pages, 14 figures

Intentional radio-frequency interference from low-cost GNSS jammers increasingly threatens the accuracy and reliability of satellite-based positioning. Mitigating this threat requires not only detection but also robust waveform classification and characterization, direction-of-arrival inference for localization, and impact estimation on receiver performance under realistic operating conditions; all of which are challenged by strong distribution shifts across devices, sensors, environments, and satellite geometries. We address these challenges by compiling a dedicated real-world dataset recorded during Jammertest 2025 (Andoya, Norway), covering two outdoor test areas with parallel measurements from a single-antenna E1/E5 receiver module and a 2x2 CRPA-array. The dataset spans diverse jamming, spoofing, and meaconing scenarios, including CW, PRN, sweep/chirp, and multi-emitter configurations, and is complemented by per-recording metadata enabling time-aligned ground truth. Methodologically, we benchmark 17 machine learning (ML) architectures for interference-modulation recognition and multi-task characterization (type, occupied bandwidth, and signal strength), and we quantify navigation-relevant degradation via a receiver-aware spectral separation coefficient (SSC) that maps measured spectra to effective (C_s/N_0)_{eff} loss. To enable multi-source analysis, we transfer a YOLOv8s and RF-DETR detector pretrained on a labeled spectrogram dataset to localize multiple simultaneous interferers in GNSS spectrograms and subsequently characterize each detected component. Results show near-99% within-area classification accuracy but substantial cross-area performance drops, highlighting the need for robustness to real-world domain shifts.

0.58

Analytical Modeling of Latency and Energy Trade-offs in FiRa-Like BLE-UWB Ranging and Localization Systems

cs.NI ·2026-10-24 ·Adelina Giurea, Jorg Wieme, Ben Van Herbruggen, Jeroen Hoebeke, Eli De Poorter
similarity 0.57
Abstract · submitted to IEEE Transactions on Mobile Computing

Accurate position and distance information provided by Ultra-Wideband (UWB) can enhance a wide range of applications. However, its receive-mode power consumption makes continuous channel monitoring impractical for energy-constrained devices. Consequently, UWB systems often rely on Bluetooth Low Energy (BLE) to discover peers and establish sessions before ranging begins. Although both technologies have been studied in isolation, an framework capturing the latency and energy consumption of the complete workflow is still lacking. To address this gap, we develop a unified analytical model for BLE-assisted UWB systems, from device-to-device ranging to infrastructure-based localization. The model includes closed-form expressions for discovery, parameter exchange, and ranging, and evaluates the resulting latency and energy consumption. Evaluation of three representative BLE configurations shows that the scanner consumes 28-57x more energy per discovery than the advertiser. In addition, the 99th-percentile discovery latency is 2-3.4x higher than the mean and reaches up to 110 s in the lowest-power configuration. The one-time BLE setup overhead is amortized after 24-562 ranging rounds, depending on the discovery configuration. Overall, the analysis demonstrates that the BLE discovery phase can dominate both the latency and the energy budget during short UWB interactions, making discovery configuration as important as the ranging scheme.

0.25

IMU-Aided Correction of Orientation-Induced Ranging Error in Bluetooth Channel Sounding on Commercial Hardware

eess.SY ·2026-09-01 ·Mihir Bapat, Santosh Nagaraj
similarity 0.56
Abstract

Bluetooth Low Energy Channel Sounding (BLE CS), standardized in Bluetooth Core Specification 6.0 (September 2024), enables distance estimation via phase-based ranging (PBR) and round-trip time (RTT). Although prior work has studied CS accuracy in configurations with a fixed orientation, no published work has studied how device orientation affects ranging error on commercial hardware. We present the first study of orientation-induced CS ranging error and a Machine Learning correction using IMU features. This study used the EFR32xG24 Channel Sounding Development Kit, the only commercial CS platform with an integrated six-axis Inertial Measurement Unit (IMU). Our results show that device orientation has a substantial effect on CS ranging accuracy; we found that a Random Forest model trained on the IMU derived orientation achieved a 74.6\% Mean Absolute Error (MAE) reduction under a Leave One Orientation Out Evaluation, demonstrating that IMU readings have potential to improve ranging accuracy.

0.18

From Least Squares to Deep Learning: Benchmarking Indoor Positioning on the HYMN Multi-Technology Dataset

eess.SP ·2026-09-22 ·Paul Schwarzbach, Muhammad Ammad
publishedcode/data similarity 0.56
Abstract

Indoor positioning benchmarks rarely co-locate multiple technologies with high-accuracy ground truth, limiting cross-method and cross-technology comparison. We evaluate four range-based positioning methods on fused Ultra-wideband, Bluetooth Low Energy, and WiFi ranges recorded at 48 reference points in an industrial facility with available ground truth. The evaluated methods range from least-squares positioning, with and without robust weighting, through a Bayesian grid filter to a ResNet regressor that we report under two protocols, interpolation and spatial generalisation. Per-technology ranging quality spans roughly two orders of magnitude, which caps any geometry-based solver that weighs anchors equivalently. On fused input the grid filter is competitive with deep learning on median error, while the ResNet's advantage concentrates on the upper tail. Holding reference points out of training increases the learned regressor's median error several-fold, exposing a spatial-generalisation penalty invisible under random splits. The dataset and evaluation code are publicly available.

0.28

Ray-Traced Augmentation for Signal Strength Based Localization

cs.NI ·2026-08-24 ·Jihoon Og, Ningze Sun, Ioanis Nikolaidis, Omid Ardakanian
similarity 0.55
Abstract · 28 pages

Indoor localization based on Wi-Fi typically relies on extensive collection of real-world received signal strength (RSS) fingerprints, making deployment costly and time-consuming. We present a ray-tracing-based framework that reduces this reliance by generating synthetic RSS fingerprints from a building model. We first calibrate the building model using a small amount of real RSS fingerprints through Bayesian optimization, followed by per-access-point calibration to account for residual errors in simulated RSS values. The calibrated model is then used to generate a large augmented dataset of synthetic RSS fingerprints at arbitrary locations. To effectively exploit these data for localization, we introduce novel binary and multivalued representations of RSS values and a ResNet-based localization architecture that supports cross-band fusion of 2.4 and 5 GHz measurements. We evaluate our localization method on a real campus building against a diverse set of four baselines. When trained exclusively on synthetic data, the proposed method with multivalued representation and upstream cross-band fusion achieves a mean localization error of 3.05m on a real-data test set, outperforming the best baseline by 33.6%. The results demonstrate that calibrated ray-tracing-based simulation can substantially reduce the need for real RSS fingerprints while enabling accurate deep-learning-based indoor localization.

0.13