CS Paper Radar

A Reusable Four-Port S-Parameter to Link-Level Signal-Integrity Analysis Framework for High-Speed Detector Interconnects

D M S Sultan, D. Bortoletto, R. Plackett, A. E. McDougall, A. S. Rotelli, A. J. A. Knight, J. Vossebeld

eess.SY hep-ex ·submitted 2026-08-10 11:31 UTC · v4

Abstract

A reusable MATLAB signal-integrity (SI) framework is presented that converts compatible four-port S-parameter data, measured by VNA or obtained from electromagnetic simulation, into traceable link-level evidence rather than a single loss metric. Its contribution is the checked, traceable automation of established SI operations while keeping source data, model assumptions, analytical projections, and finite-record observations distinct. The framework is demonstrated on the four 1.25 Gbps differential routes (DP1-DP4) of the PPCB-1347-MuPix11 probe card using PTSL CST Microwave 3D-Solver-derived four-port S-parameters and a virtual time-domain solver. The automated pipeline preflights file structures, performs a power-normalized mixed-mode transformation, applies route-length-aware loss decomposition, constructs a causally loaded channel model, and propagates full PRBS-31 sequences into eye-diagram, conditional-BER, and 8b10b-coded-link analyses. At the 1.25 Gbps data rate (Nyquist 0.625 GHz), DP1-DP4 exhibit differential insertion loss (SDD21) from -0.350 to -0.300 dB, differential-to-common conversion from -31.038 to -28.236 dBc, and modeled FEB-input eye openings from 0.586 to 0.588 V. The comparison shows that path length alone is not an adequate SI ranking variable: DP3 has the lowest Nyquist insertion loss, DP1 the strongest differential-to-common isolation, and DP4 the largest modeled eye. All analytical BER values remain below the reporting floor and therefore do not support a BER ranking. By preserving the distinction between route-dependent waveform behavior, model projections, and finite-record observations, the framework provides an extensible basis for comparative high-speed-interconnect SI analysis from design review through calibrated VNA measurement interpretation.

Closest papers

Nearest neighbours by meaning across the whole index.

Route-Aware EM Surrogate for Automated LC Matching Network Optimization

cs.AR eess.SP ·2026-10-30 ·Subhadip Ghosh, Surya Srikar Peri, Ramesh Harjani, Sachin S. Sapatnekar
code/data similarity 0.49
Abstract · Submitted to the IEEE International Symposium on Circuits and Systems (ISCAS) 2027

This paper proposes an open-source automated LC matching network optimization framework that combines schematic-level design optimization with electromagnetic (EM)-aware post-layout refinement. An ML-based surrogate predicts the frequency-dependent complex admittance of individual routes, enabling reuse across matching network topologies and physical layouts for the same technology node without retraining. These route models guide post-layout passive retuning to recover matching performance while preserving the layout footprint. Evaluated in a commercial 65nm CMOS technology, the surrogate achieves 1.94-4.91% mean absolute percentage error with respect to a full-wave electromagnetic solver, with no detected passivity violations. Across nine LC matching networks operating at 5-95GHz, our framework recovers S_11 from -6.37dB, for schematic-level optimization after post-layout degradation to -22.27dB after EM-aware post-layout refinement. All designs meet matching targets under full-layout EM verification in optimization runtimes below 70s.

0.34

Distributed Fiber Monitoring on a Coherent DSP ASIC: Implementation of Longitudinal Power Monitoring

eess.SP physics.optics ·2026-11-19 ·Takeo Sasai, Yukinobu Nakajima, Minami Takahashi, Runa Kaneko, Masanori Nakamura +3 more
similarity 0.47
Abstract · 11 pages, 19 figures

Coherent DSP ASICs and transceivers to date report a rich set of optical link metrics, yet these remain cumulative over the link and provide no spatial localization. This paper presents the implementation design of fiber-longitudinal power monitoring (LPM), which recovers spatially resolved power profiles from received traffic, on a coherent DSP ASIC chip. We first identify the challenges specific to DSP implementation, and describe the enabling algorithm and architecture. We then present the key design considerations for retaining the estimation fidelity of the on-chip LPM during in-service operation. On this basis, we implement LPM on a coherent DSP, a 3-nm 800G low-power DSP ASIC housed in an OSFP pluggable module, which constitutes, to our knowledge, the first coherent DSP ASIC and transceiver to perform distributed fiber monitoring and data communication simultaneously. The on-chip LPM is experimentally validated over links of up to 1005 km using 400ZR+ and 800ZR+ traffic, with no measurable impact on Q factor or module power consumption. Multi-vendor interoperability is also demonstrated, where the on-chip LPM operates on signals transmitted by third-party transceivers. These results extend coherent DSPs from cumulative to spatially resolved monitoring, allowing pluggable transceivers, deployable from DCI to long-haul, to act not only as cost-efficient transmission elements but also as distributed monitoring points across diverse optical network infrastructure.

0.31

The Era of Vibe Tapeout: Dark Age or Golden Age for Analog Circuit Design?

cs.AR ·2026-10-11 ·Kentaro Yoshioka
benchmarkunusual similarity 0.47
Abstract

LLM agents now write their own schematic and layout generators, run EDA tools, read the results, and fix the design. This "vibe tapeout" is becoming practical for analog circuits as well. This paper measures how far it has come in two settings. (A) On an open PDK (SKY130), a cloud LLM agent designed an 11-bit, 5.12-MS/s SAR ADC from its specification. The agents produced DRC- and LVS-clean macros and met the specification after parasitic extraction (PEX). In particular, under the condition in which the agent received a sanitized reference design derived from our 65-nm design (vibe porting), it produced the best layout in the shortest time. Its area was 1/1.6 to 1/2.8 of that of the conditions without a reference. This condition reached signoff without human intervention. The agents also identified the causes of post-PEX degradation (CDAC wiring coupling and common-mode-dependent comparator offset) by their own experiments. On the other hand, agents sometimes reported false passes, and verification independent of the design agent was essential. (B) A commercial PDK is under NDA and cannot be given to a cloud LLM. We therefore evaluated local LLMs running on university servers with a six-task benchmark on a commercial 65-nm CMOS PDK. Kimi K3 passed five of the six tasks, while MiniMax M3 passed two. Neither solved the debugging task, which requires finding the cause from symptoms. Finally, we discuss the prospects for extending vibe tapeout from ADCs to entire SoCs, and ask whether vibe tapeout is a dark age or a golden age for analog design. Our answer is that it is a golden age for designers who know what to verify.

0.50

s-MDM: Generative Virtualization of Multi-Device Hardware Variations for Portable DL-SCA

cs.CR ·2026-09-16 ·Niloufar Sayadi, Marten van Dijk, Chenglu Jin
published similarity 0.46
Abstract

Deep Learning-based Side-Channel Analysis (DL-SCA) frequently suffers from catastrophic performance degradation across unseen hardware due to printed circuit board routing differences, silicon process variations, and measurement noise shifts. This poster presents the Synthetic Multiple Device Model (s-MDM), a zero-target-trace generative framework designed to improve cross-device portability. s-MDM combines a structured cVAE generator, a Walsh-Hadamard leakage anchor, continuous style modulation, and decoupled leakage-style--domain critics to synthesize virtual source-device profiles offline. Benchmarked on 32-bit side-channel traces (AES_PTv2), s-MDM maps a precise operational boundary: while physical MDM remains superior on identical electrical clones (D4), s-MDM achieves consistently low key rank on the layout/acquisition-shifted Pinata target, where physical baselines are unstable or misaligned.

0.39

Timing Skew Estimation of Time-Interleaved ADC based on Inter-Channel Correlations without Computing Derivative of Input Signal

eess.SP eess.SY ·2026-10-19 ·Bibhu Datta Sahoo, Gabriele Manganaro
similarity 0.46
Abstract

Time-interleaved analog-to-digital converters (TI-ADCs) enable multi-gigasample-per-second throughput in high-speed applications, but sub-picosecond timing skews among interleaved channels introduce large spectral artifacts that degrade dynamic performance. To continuously track parametric drifts without interrupting normal operation, background calibration is required. However, extracting timing skews under unknown inputs is challenging, and many existing correlation-based methods rely on resource-heavy derivative filters that restrict input bandwidth. This article proposes a novel background timing-skew estimation technique for two-channel TI-ADCs that overcomes these limitations. Closed-form timing-skew expressions are derived using: (a) adjacent-channel cross-correlation combined with single-channel auto-correlation for sinusoidal inputs, and (b) adjacent-channel cross-correlation for Wide-Sense Stationary (WSS) inputs, specifically bandpass-filtered wideband noise and Orthogonal Frequency Division Multiplexed (OFDM) signals. The derived analytical models are validated through comprehensive simulations, offering an efficient framework for real-time background calibration in high-speed data converters.

0.17

TLF: Rapid Characterization of RF Transceiver Parameters in Embedded Systems via Bus-Level Interception

cs.CR ·2026-08-13 ·Larry Hernandez, Sergey Bratus
published similarity 0.46
Abstract · Accepted for publication in the Proceedings of the 2026 IEEE Military Communications Conference (MILCOM 2026). This is the authors' accepted…

We present TLF (Transceiver Lifter Framework), a tool for recovering RF transceiver configuration and runtime behavior from bus-level traces captured between a microcontroller and its transceiver IC. A stateful protocol decoder, built against the transceiver's register and data interface, reconstructs operating RF parameters and behavior from intercepted register writes and FIFO transfers. For bus-attached transceivers whose hardware-cryptography keys are loaded through the intercepted host interface, key material is also recoverable. Where the firmware drives frequency hopping -- either through a hardware-assisted engine or a custom schedule -- the decoder extracts the channel table, hop sequence, and timing. We evaluate the approach on two targets from different Semtech families: an SX1233-based UAV C2 modem employing firmware-level FHSS with per-packet sync word rotation, and an SX1276-based Meshtastic node exercising the LoRa register overlay. From a single bus capture, processed in seconds, TLF recovers the complete register-exposed RF configuration (modulation, band plan, phase behavior) without prior knowledge of the target firmware -- sufficient to configure a matched receiver or develop targeted countermeasures. Above the chip layer, a pluggable protocol decoder interprets recovered FIFO payloads as application PDUs, demonstrated end-to-end on Meshtastic. Firmware-level cryptographic state remains, as expected, opaque. The approach requires physical access or emulation of the target hardware, and its recovery depth is bounded by the transceiver's register interface: parameters implemented entirely in firmware (custom FEC, whitening, encryption) are observable only as opaque FIFO payloads.

0.25

Signal Design Impacts on GNSS and LEO-PNT L1 Band Acquisition Complexity: A Case Study with Xona Pulsar

eess.SP ·2026-10-19 ·Jérôme Leclère, Rajnesh Joshi, Thyagaraja Marathe, Tyler G. R. Reid
published similarity 0.46
Abstract

GNSS signal acquisition is the process of detecting and estimating signal parameters by exploiting correlation operations that provide processing gain and enable the detection of signals below the noise floor. The design of an acquisition engine requires balancing achievable sensitivity, computational complexity, memory requirements, power consumption, and implementation complexity. In particular, increasing coherent and non-coherent integration times improves sensitivity but can significantly increase receiver processing requirements, limiting its applicability in low-power and resource-constrained receivers. This paper presents a comparative analysis of L1-band signal acquisition complexity by evaluating the required integration time and corresponding implementation requirements for different signal designs under equivalent acquisition performance targets. The analysis considers the impact of signal characteristics, including spreading codes, secondary codes, modulation, and signal bandwidth, on coherent and non-coherent acquisition performance. For a given attenuation level and target probability of false alarm and detection, the required integration times are derived and translated into acquisition complexity metrics, including arithmetic operations, processing time, and memory requirements. The analysis is applied to Pulsar X1, a LEO-enabled PNT signal, and representative GNSS L1 signals to determine under which attenuation, assistance, and integration conditions the higher received power of LEO-PNT translates into reduced receiver acquisition workload. By relating the required integration to arithmetic operations, processing time, and memory requirements, the study provides a receiver-level comparison relevant to both conventional and snapshot-based receivers, where reducing acquisition processing can directly contribute to lower energy consumption.

0.35

xCHEM: SDR-Based Multi-Link Channel Emulator for Real-Time Hardware-in-the-Loop Digital-Twin

eess.SP ·2026-10-28 ·Ali Saeizadeh, Gabriele Gemmi, Tamerlan Aghayev, Michele Polese, Pedram Johari +1 more
similarity 0.46
Abstract · 13 pages, 16 figures, 4 tables

This paper presents xCHEM, a radio-frequency channel emulator that inserts programmable channels between physical radios using a single NI USRP X4xx software-defined radio. External channel models stream impulse responses to its field-programmable gate array without firmware changes or interruption of signal processing. A streaming datapath implements six independently configurable directional channels across four radio interfaces. Each channel uses a sparse finite impulse response filter whose memory-backed delays decouple delay span from multiplier resources. The real and complex variants support 32 and 16 nonzero taps, respectively, with a maximum delay of 16666.62 ns and 4.069 ns resolution. Coefficient scaling and arithmetic right shifts control attenuation. Hardware measurements show root-mean-square errors of 9.5 ps in delay over the full span and 0.11 dB in attenuation. Multipath delays are recovered within one sample. An FPGA coefficient engine produces tested Doppler shifts from +/-1 Hz to +/-1 MHz with mean frequency errors below 0.032 Hz relative to quantized commands after carrier-offset calibration; at 200 Hz, it reduces the measured near-carrier spur by 53.3 dB compared with 1 kHz host updates.

0.39