CS Paper Radar

Simultaneous Digital Communication and Deformation Sensing over a Single Stretchable Interconnect

Yuji Isano, Hiroki Ota

cs.ET cs.HCphysics.app-ph ·submitted 2026-08-26 13:50 UTC · v1

Abstract

Stretchable hybrid electronics integrate rigid solid-state electronics with stretchable materials and structures to achieve both high deformability and stable electronic performance. However, most existing systems treat stretchability only as a mechanical attribute without exploiting device deformation to encode its own mechanical state. This problem arises from adapting conventional rigid circuit architectures to stretchable substrates, affording a loss in compatibility with the sensors required for strain measurement. This study addresses this issue by proposing a communication-integrated deformation sensing architecture for stretchable hybrid devices. In the proposed approach, standard universal asynchronous receiver-transmitter digital signals transmitted between rigid nodes are amplitude-modulated by strain-induced resistance changes in stretchable liquid metal interconnects. By reading both amplitude changes and digital patterns, the system enables simultaneous digital communication and self-deformation sensing without requiring additional stretchable sensing elements. The architecture is demonstrated in a multi-node system and applied to wearable sensing and self-deformation mapping devices. By extending the integration of rigid circuits and soft elements from the hardware level to the system level, this study provides a novel design paradigm for stretchable electronic systems that inherently utilize their own deformation as functional information.

Comment
41 pages, 4 figures, 18 supplemental figures, will be submitted to Advanced Functional Materials

Closest papers

Nearest neighbours by meaning across the whole index.

SaddleSense: Saddle-Shaped Modules for 3D Shape Sensing with Single-Axis Off-the-Shelf Bend Sensors

cs.RO ·2026-10-31 ·Dong Heon Han, Runze Zuo, Chankyo Kim, Saima Jamal, Daniel Bruder
similarity 0.57
Abstract

Accurate posture feedback is essential for precise control of continuum robots. Off-the-shelf bend sensors measure curvature about only one axis; without a suitable mounting arrangement, they can restrict robot motion and provide incomplete posture information. SaddleSense introduces a 3D-printed thermoplastic polyurethane (TPU) saddle-shaped lattice that holds one commercial bend sensor along each curved edge. Because each sensor flexes within its own channel rather than spanning the segment axially, the lattice converts multi-axis body deformation into sensor curvature without tying segment length to sensor length. Each four-sensor module accommodates two-axis bending, contraction, and extension while quantifying all three deformation modes across its four readings. A hybrid calibration maps the sensor readings to piecewise constant curvature (PCC) parameters using a learned model paired with a physics-based fallback for out-of-distribution inputs. We demonstrate a six-module prototype with 24 off-the-shelf bend sensors on a 430~mm continuum body. Using only each module's four local readings, the physics-based model alone achieves a tip position root mean square error (RMSE) of 29.9~mm (7.0\% of body length). The data-driven model reduces the tip RMSE to 13.2~mm (3.1\%) on held-out samples of motions similar to the training set and 15.8~mm (3.7\%) on separately recorded trials. Reducing each module from four sensors to one nearly triples the tip error.

0.32

X-Hinges: 3D Printing Self-Sensing Compliant Mechanisms for Continuous and Multi-DOF Motion Sensing

cs.HC ·2026-09-10 ·Xiang Chang, Haiyang Yan, Stefanie Mueller, Jiaji Li
top venue similarity 0.53
Abstract · Accepted at ACM UIST 2026. 15 pages, 24 figures. Author's accepted manuscript

We present X-Hinges, a design and fabrication method for self-sensing compliant mechanisms based on multi-material FDM 3D printing. By co-printing two conductive filaments of different conductivities within a compliant body, we embed resistive sensing elements directly during fabrication without post-assembly, enabling continuous motion sensing across multiple degrees of freedom in a single print. The structure supports three degrees of freedom, each equipped with a dedicated sensing element configuration for multi-DOF motion estimation. We develop a precision data acquisition system and data-driven regression models that enable continuous, real-time motion sensing. We also introduce an interactive design tool for customizing the geometry, mechanical properties, degrees of freedom, and sensing configurations of X-Hinges. The tool also supports augmenting existing 3D models with self-sensing structures, endowing ordinary objects with continuous multi-DOF sensing capabilities. Finally, we present a set of application examples demonstrating the capability of X-Hinges for fabricating personalized interactive interfaces.

0.47

History-Aware Force Sensing and Tunable Stiffness in a Pneumatic Kresling Origami Cell

cs.RO ·2026-11-01 ·Hengyi Zhou, Jiaqi Wang, Yilin Ma, Dezhong Tong, Xiaonan Huang
similarity 0.52
Abstract

Mechanical hysteresis and pneumatic loading complicate contact force estimation from deformation measurements in soft robots. This work presents a 3D-printed polyether block amide (PEBA) Kresling cell with magnetic angular sensing that supports three operating modes: force sensing at zero gauge pressure, force sensing with tunable stiffness under gauge positive pressure, and self-sensing actuation under negative gauge pressure. A multiscale gated recurrent unit (GRU) network estimates contact force from angular histories to account for the the combined effects of geometric deformation and material response. At zero gauge pressure, the model achieves a test RMSE of 0.76~N. Positive gauge pressure approximately doubles the average axial loading stiffness at +20~kPa over the first 3~mm of compression, while pressure-specific models maintain RMSEs below 0.93~N. Under negative gauge pressure, an energy-based compensation model enables contact force estimation using the the model trained at zero gauge pressure, achieving RMSEs of 1.66--2.10~N under quasi-static conditions. These results demonstrate a compact approach to combining force feedback, tunable axial stiffness, and self-sensing actuation in soft origami systems.

0.36

A Reconfigurable Fabric Based Pneumatic Actuator with Button Fastened Constraint Modules for Multi Mode Actuation

cs.RO ·2026-10-08 ·Kentaro Kimura, Hiroki Ishizuka, Yusuke Sakaue, Sei Ikeda, Osamu Oshiro
similarity 0.51
Abstract · IEEE Access in Revision

Soft pneumatic actuators are widely used in soft robotics. However, their actuation modes are typically fixed by internal chamber designs or reinforcements, making post fabrication reconfiguration difficult. This paper presents a reconfigurable fabric-based pneumatic actuator that enables rapid, tool free, and reusable switching among multiple actuation modes by attaching constraint fabric modules to a buttoned textile sleeve. By rearranging low-stretch constraint parts on a single actuator body, the proposed system realizes four actuation modes isotropic expansion, contraction, bending, and twisting without redesigning or disassembling the actuator.We further introduce an attachable capacitive fabric-based tactile sensor module that can be mounted at arbitrary locations on the actuator surface for task dependent contact sensing. Experiments demonstrated an elongation ratio of 1.2, a maximum bending angle of approximately 60 degrees, and a twisting angle of approximately 90 degrees at 24 kPa, while achieving blocking forces exceeding 10 N across all modes. The tactile sensor exhibited a monotonic, force-dependent increase in capacitance with low hysteresis (approximately 12%) and stable cyclic responses under preload. Finally, we constructed soft robotic arms composed of multiple actuators and demonstrated in situ motion reconfiguration for grasping by changing the attached constraint patterns. These results indicate that the proposed modular constraint and sensing framework improves the functional adaptability of fabric-based soft robots while preserving a simple, robust actuator structure.

0.23

A Wearable Pneumatic Device for Continuous, Closed-Loop, Bidirectional Tactile Interaction

cs.RO ·2026-09-01 ·Cosima du Pasquier, Aliyah Smith, Serin Huber, Joshua Phelps, Ilana A. Cohen +3 more
similarity 0.50
Abstract

We present a system of two wearable pneumatic haptic devices that supports continuous, closed-loop, bidirectional tactile interaction at perceptually relevant force and temporal scales. A single device can contain up to twelve pressure sensing channels connected to textile-based pneumatic pouches. Each channel in a device can be used as a sensor, an actuator, or both. As an actuator with integrated sensing, the channel generates stable skin indentation through local closed-loop control. As a sensor, a channel can be mounted (or worn) on any surface, including on a robot gripper or on the human body, and used to measure touch interactions with the environment or a human user. A distributed architecture supports sustained pressure output, rapid dynamic response, and wireless pairing of identical devices in a system to transmit and reproduce tactile pressure signals in real time. Device-level characterization demonstrates force bandwidth exceeding 30 Hz, rapid and well-damped step responses, and extended pressure retention compared to prior compact pneumatic platforms. Human studies show that pressure-based fingertip feedback enables discrimination of force and stiffness, improves teleoperated manipulation by reducing applied pressures by up to 23.1% and task duration by up to 27.4%, and lowers subjective mental workload by 18.8%, particularly under visually constrained conditions. By unifying tactile sensing and haptic feedback within a single pneumatic modality, the device provides a practical foundation for bidirectional touch interaction in teleoperation.

0.14

A Monolithic Force-Proprioception Soft Acutuator Enabled by Single-Material 3D printing

cs.RO ·2026-09-21 ·Nan Huang, Lele Liu, Junfeng Lu, Yipan Zhu, Jiansheng Dai +1 more
similarity 0.50
Abstract

Pneumatic proprioceptive actuators integrate actuation and sensing for soft robots that attract interest due to functional potential. Existing approaches often suffer from assembly errors or stress concentrations caused by heterogeneous materials. In this work, we propose the Monolithic Force-Proprioception Soft (MFPS) design and fabrication method that integrates an Asymmetric Origami Bending (AOB) chamber and a Force-Proprioception Soft (FPS) sensor with single material through one-step Fused Deposition Modeling (FDM) fabrication. Based on the resistance response to strain of conductive thermoplastic polyurethane (TPU), we design and analyze the structure of the FPS sensor, and conduct parametric analysis on the sensing characteristics. The FDM fabrication parameters of the MFPS actuator are analyzed, followed by actuator fabrication and characterization of the actuation and proprioception performance. Experimental results show that the MFPS actuator achieves a bending angle of 40°, an output force of 12.5 N, and a resistance change of 26.9% as the applied external force increased from 0 to 45 N. A two-finger force-proprioception gripper is developed based on the MFPS actuator. The grasping and force-proprioception capabilities are experimentally validated, proving that the MFPS design method provides a new approach for the development of self-sensing actuators.

0.20

Reliable Piezoresistive Strain Sensing Through Physical Limits and Uncertainty Monitoring

cs.RO ·2026-08-16 ·Carmen Ballester, Víctor Muñoz, Dorin Copaci, Dolores Blanco
similarity 0.50
Abstract

Soft piezoresistive strain sensors are one of the most common sensing solutions for wearable and soft robotic applications due to their flexibility and compliance. However, their resistance response is nonlinear and hysteretic, and a sensor can be pushed past its calibrated workspace or misbehave inside it, carrying that error into a decision or control loop. Probabilistic regressors track confidence but ignore those limits. A predictive mean can look unremarkable even when the reading comes from a sensor outside its admissible range or already failing internally, so a confident-looking estimate is not the same as a trustworthy one. This paper proposes a reliability framework pairing a physics-informed probabilistic inverse model, built on physics-guided input features, with a risk factor fusing uncertainty with strain and strain-rate limits into a three-state monitor. Tests on a Nitinol wire and a silver-coated polyamide thread with a Gaussian Process raised fit scores to 0.90-0.95 (RMSE 0.26%-0.15%) and a 96% empirical coverage against the 95% target. The monitor caught 95% of out-of-range and 100% of abnormal conditions while staying reliable under nominal operation. A sensor that reports confidence alongside its estimate lets a system withhold action instead, since it needs no labeled failure examples, which are hard to collect for soft materials.

0.04

Topology optimisation and simulated state reconstruction for self-sensing piezoresistive grippers

cs.CE ·2026-09-13 ·Connor N Mallon, Zachary J Wegert, Anthony P Roberts, Joshua Pinskier, Harry Bowman +1 more
similarity 0.50
Abstract

We consider the computational design of a self-sensing robotic gripper that has the potential to reduce reliance on traditional external sensors. We computationally investigate the potential of a novel sensing method that exploits the coupled electromechanical properties of piezoresistive materials to enable mechanical perception using sparse electrical measurements. In this theoretical proof-of-concept, we show that under the idealised assumptions of linear constitutive relationships and quasi-static gripper operation, it is possible to reconstruct simple contact shapes and gripper displacement fields using a small number of simulated electrical measurements, suggesting the potential of the proposed sensing technique. We use topology optimisation to promote the quality of displacement state recovery by adding an electrical performance objective to the mechanical compliance requirement of the gripper. Using the proposed reconstruction technique, we showcase the improved reconstruction ability of an electrically optimised gripper design through an increased robustness to noisy synthetic measurements compared to a gripper designed with only a mechanical objective in the topology optimisation problem. In the future, detailed inclusion of non-linear effects and experimental realisation of this theoretical proof-of-concept may help remove the constraints of traditional sensors for robotic handling, potentially facilitating sensing in settings where current sensing systems are impractical.

0.29