CS Paper Radar

Elastoplastic inherent strain-based topology optimization for residual stress reduction in metal additive manufacturing

Takao Miki, Jike Han, Kazuhiro Izui, Shinji Nishiwaki

cs.CE ·submitted 2026-09-07 11:00 UTC · v2

Abstract

This paper proposes a topology optimization method for reducing the residual stress arising in the building process of metal additive manufacturing. First, a layer-by-layer process analysis model based on an elastoplastic inherent strain method is introduced. In this model, the incremental displacement is solved anew at each layer step, and the stress history is explicitly incorporated into the constitutive equation as the stress accumulated up to the previous step, which guarantees the stress continuity across layer interfaces without introducing activation strains. Next, the design sensitivity of this analysis model is derived based on the adjoint method. Taking the pair of the stress and the equivalent plastic strain as the state variables reduces the dependency between layer steps to a one-step recurrence, and the adjoint fields are constructed as a layer-by-layer reverse sweep that reuses the coefficient tensors obtained in the forward analysis. Consequently, the cost of the sensitivity analysis scales linearly with the number of layers and remains of the same order as that of the forward analysis. An optimization problem is then formulated based on the density method to minimize the P-norm of the residual stress at the completion of the building process under the volume and final-use compliance constraints, and the derived sensitivities are verified by comparison with central finite differences. Finally, the proposed method is demonstrated through two- and three-dimensional examples of residual stress minimization under a compliance constraint. The results clarify that, under the elastoplastic analysis, the maximum residual stress is bounded by the yield surface, and the optimization therefore reduces the extent of the yielded and plastic strain accumulating regions rather than the peak stress value.

Comment
34 pages, 17 figures, 6 tables. v2: Figures 15-17 (three-dimensional results), which were missing in v1, are now included. No other changes

Closest papers

Nearest neighbours by meaning across the whole index.

Sensitivity Hot Spot Penalization: A Robust Topology Optimization Framework against First-Order Worst-Case Perturbations

cs.CE ·2026-08-31 ·Junpeng Wang, Niels Aage, Ole Sigmund
similarity 0.56
Abstract

Deterministic topology optimization can efficiently generate high-performance structural designs, but it does not explicitly control localized fragility induced by manufacturing variations and geometric uncertainties. Such fragility often appears as stress concentrations or hinge-like deformation mechanisms. Conventional robust topology optimization can suppress these features, but typically requires multiple design realizations and substantially increased computational cost. Recent work by Sigmund et al. (2026) introduced sensitivity hot spot penalization (SHoSP), which augments the nominal objective by a smooth maximum of its sensitivities and suppresses localized fragile features at low additional cost while promoting more even stress distributions. This paper establishes a general connection between SHoSP and a first-order worst-case robust approximation under a material-mass perturbation budget using a Taylor expansion and H{"o}lder's duality. The original penalty weight is identified as a dimensionless norm-bounded perturbation budget relative to the area (2D) or volume (3D) of the design domain. This interpretation explains the suppression of sensitivity hot spots, hinge localization, and stress concentrations by limiting the maximum first-order degradation under budgeted perturbations. It is investigated for compliance minimization and compliant mechanism design. Robustness is assessed using a relaxed worst-case density perturbation and by comparing deterministic and SHoSP designs under equivalent perturbation budgets. Stress-related effects observed on structured meshes are cross-validated by stress-oriented topology optimization and body-fitted finite element analyses. Extensions to porous infill optimization, multiple load cases, and large-scale 3D examples further demonstrate the applicability and superior scalability of the SHoSP framework.

0.22

Buildability Assessment of 3D-Printed Concrete Structures Using Smoothed Mohr-Coulomb Plasticity with Isotropic Hardening

cs.CE math.NA ·2026-09-07 ·Saif-Ur-Rehman, Annika Robens-Radermacher, R. J. M. Wolfs, Jörg F. Unger
similarity 0.52
Abstract

Extrusion-based 3D concrete printing builds structural elements layer upon layer without formwork, so freshly deposited material must carry the growing weight of the structure while it is still gaining strength and stiffness. The largest number of layers that can be printed before failure, the buildability, is therefore central to process design. Its prediction rests above all on how accurately the constitutive model represents fresh concrete. Existing finite element frameworks pair gradual pre-failure hardening only with smooth yield surfaces, which leaves the Mohr-Coulomb surface that best describes fresh concrete restricted to perfect plasticity. This work combines a smoothed Mohr-Coulomb yield surface with nonlinear isotropic hardening of the cohesion, formulated in an updated Lagrangian setting with an activation field for layer deposition. Failure is identified from a tangent-stiffness eigenvalue criterion that matches the analytical self-weight buckling load of a slender wall and is insensitive to geometric imperfection. The framework reproduces the measured collapse of a printed straight wall within one layer and predicts the collapse of a hollow cylinder closer to experiment than existing frameworks. A study over six diameters and six hardening rates shows buildability peaking at intermediate diameters and rising with the hardening rate. Recording how much of its strength the material has used at failure, slender cylinders fail with much still in reserve while intermediate ones use nearly all of it. The two failure modes are therefore identified as the limits of one process rather than separate failure mechanisms.

0.48

Multi-Objective Optimization Under Uncertainty of Part Quality in Fused Filament Fabrication

cs.CE cs.LGmath.NAmath.OC ·2026-08-19 ·Berkcan Kapusuzoglu, Paromita Nath, Matthew Sato, Sankaran Mahadevan, Paul Witherell
publishedhighly cited similarity 0.52
Abstract · ASCE-ASME Journal of Risk and Uncertainty in Engineering Systems, Part B: Mechanical Engineering

This work presents a data-driven methodology for multi-objective optimization under uncertainty of process parameters in the fused filament fabrication (FFF) process. The proposed approach optimizes the process parameters with the objectives of minimizing the geometric inaccuracy and maximizing the filament bond quality of the manufactured part. First, experiments are conducted to collect data pertaining to the part quality. Then, Bayesian neural network (BNN) models are constructed to predict the geometric inaccuracy and bond quality as functions of the process parameters. The BNN model captures the model uncertainty caused by the lack of knowledge about model parameters (neuron weights) and the input variability due to the intrinsic randomness in the input parameters. Using the stochastic predictions from these models, different robustness-based design optimization formulations are investigated, wherein process parameters such as nozzle temperature, nozzle speed, and layer thickness are optimized under uncertainty for different multi-objective scenarios. Epistemic uncertainty in the prediction model and the aleatory uncertainty in the input is considered in the optimization. Finally, Pareto surfaces are constructed to estimate the tradeoffs between the objectives. Both the BNN models and the effectiveness of the proposed optimization methodology are validated using the actual manufacturing of the parts.

0.64

Lattice Structure Optimization for Additive Manufacturing: Manufacturability-Driven Design and Pareto Front Construction

cs.GR ·2026-09-27 ·Yu Xing, Yang Liu, Lin Lu
published similarity 0.52
Abstract · This manuscript is an English translation of a Chinese article accepted for publication in the Journal of Computer-Aided Design & Computer G…

Lattice metamaterials support lightweight, multifunctional structures, while additive manufacturing (AM) enables complex geometries. Yet multiphysics lattice design faces two challenges: efficiently constructing well-covered multi-objective Pareto fronts under limited budgets, and satisfying manufacturing constraints such as overhangs, enclosed cavities, and restricted powder-removal channels. We propose a manufacturing-constraint-driven method for lattice optimization and Pareto-front construction. Differentiable manufacturing constraints are embedded in inverse-homogenization topology optimization, enabling joint optimization of physical performance and manufacturability. A progressive Pareto-front mechanism uses a density-generation network to learn latent representations of high-quality lattices, interpolates neighboring nondominated representations, and decodes them into initial density fields for subsequent optimization. Newly found nondominated solutions update the network and sample set, progressively expanding the manufacturable set. On 3D periodic unit cells, with 1000 optimization runs, network initialization achieves a 92.60% success rate and 916 manufacturable samples, versus 78.30% and 776 for random initialization. Its Pareto front reaches a hypervolume of 0.0787, compared with 0.0675 for random initialization. The results show that the method efficiently constructs broadly covered manufacturable Pareto fronts for multiple physical properties.

0.38

Allen--Cahn Residual-Constrained Topology Optimization via an Augmented Lagrangian Method

cs.CE math.OC ·2026-11-02 ·Run Du, Xuan Xiao, Wenming Cheng, Zeqiang Zhang
benchmark similarity 0.50
Abstract · 43 pages, 14 figures

This paper presents a residual-constrained topology optimization framework that controls interface transition bandwidth without requiring external density filters. The steady conserved Allen--Cahn (AC) equation is formulated as an equality residual constraint and solved via a mass-weighted Augmented Lagrangian Method (ALM) coupled with the Method of Moving Asymptotes (MMA). A closed-form chemical potential projection eliminates the constant residual mode, ensuring algebraic compatibility with external volume targets. Variational sensitivity analysis reveals a symmetric-plus-rank-one Jacobian that yields matrix-free sensitivities without additional adjoint PDE solves, reducing residual sensitivity overhead to only 0.11% of the state elasticity solve time in 3D. Systematic 2D benchmarks confirm that interface bandwidth is governed intrinsically by reaction--diffusion parameters across mesh refinements. While diffuse interfaces incur a continuous compliance elevation (1.4%--12.3%), a volume-preserving 0/1 post-processing audit across 48 benchmark cases demonstrates that this gap stems primarily from intermediate-density penalization: binarized AC-ALM designs achieve equal or superior stiffness in 45 configurations (averaging 1.2% stiffer than SIMP). Simultaneously, single-node hinges and strut fragmentation are substantially suppressed compared to unregularized baselines. Three-dimensional benchmarks further demonstrate practical spatial viability for complex structures.

0.30

Constrained neural softening functions for the Mullins effect in parameter-dependent materials

cs.CE ·2026-10-25 ·Dominik K. Klein, Jonas Fey, Maximilian Kannapinn, Oliver Weeger
similarity 0.50
Abstract

Accurately capturing the Mullins effect across varying material compositions remains challenging, as constitutive models must unify flexible representations of stress softening with physical consistency and robust parameter calibration. In this work, we investigate parameter-dependent physics-augmented neural network constitutive models within the pseudo-elastic modeling framework, focusing on structural constraints that ensure physically admissible neural softening functions. This paper has three key contributions: (1) We formulate different neural softening functions within the pseudo-elastic framework, including a multiplicative decomposition of the softening function that enables parameter-dependent ansatz functions satisfying common mechanical constitutive conditions by construction. (2) We derive a sufficient condition for ellipticity of pseudo-elastic constitutive models, which can be enforced in the constitutive models by construction. (3) We systematically investigate how flexibility and structural constraints influence the performance of neural softening functions in terms of prediction accuracy and calibration robustness. For this, we consider multiaxial experimental data of carbon black-filled EPDM rubber synthesized with varying amounts of curatives. The findings of our work suggest that neural softening functions are a promising extension of the classical pseudo-elastic framework and, when subject to suitable constraints, can improve predictive accuracy for highly nonlinear, parameter-dependent materials.

0.28

Generative AI-Driven Parametric Design Optimization Framework for Vehicle Closure Systems

cs.LG ·2026-11-16 ·Dongeon Lee, Yurim Lee, Jiyong Kim, Sanghyeon Kim, Sanghyun Lee +3 more
similarity 0.50
Abstract · 26 pages, 15 figures

This study presents a generative AI-driven parametric design optimization framework integrating performance-oriented generation with editable computer-aided design (CAD) and downstream computer-aided engineering (CAE) analysis for industrial vehicle closure systems. The framework is demonstrated on an automotive tailgate assembly with complex geometry, coupled components, and competing performance and feasibility requirements. A production-oriented CATIA model is restructured into a reference-based parametric template with a 13-dimensional design representation. An automated CAD/CAE workflow generates parametric models, performs structural analysis, and constructs a database of mass, maximum displacement, and maximum von Mises stress. Gaussian process regression surrogates predict performance, while diffusion and flow matching models generate design candidates. The design problem minimizes mass and maximum displacement, with stress assessed as an engineering feasibility constraint. Performance-guided generation using surrogate guidance and performance-aware training using a performance-aware loss incorporate engineering objectives, with sensitivity to guidance scale and loss weight evaluated. Generative search is compared with NSGA-II under matched evaluation budgets using a common surrogate model. Selected Pareto-region candidates are reconstructed in CATIA and re-evaluated through native CAE; all verified candidates are successfully regenerated and analyzed. Relative to the baseline, the knee-point design reduces mass by 7.1% and maximum displacement by 29.4%, while extreme verified solutions achieve maximum reductions of 10.3% and 37.3%, respectively. The results demonstrate performance-oriented multi-objective design exploration compatible with editable industrial CAD and native engineering verification.

0.30

HGTO: A Unified Graph-Based Physics-Informed Formulation for Structural Topology Optimization

cs.LG ·2026-09-14 ·Kangzheng Liu, Uday Kumar Punna, Leixin Ma
similarity 0.50
Abstract

Density-based topology optimization is typically structured as a nested sequence of material updates, structural analyses, and sensitivity assessments. While neural density parameterization and dual-field physics-informed approaches provide data-free alternatives, most existing methods represent density and displacement as coordinate fields and make limited use of the discrete relationships inherent in the finite element mesh. The present study introduces HGTO, a unified graph-based formulation that extends complete neural topology optimization from coordinate space to finite-element graph space. Element densities are parameterized on the element graph derived from the mesh, and the structural state is determined on the corresponding node--element hypergraph. Finite element kinematics, numerical quadrature, constitutive response, and force assembly remain explicitly defined operations within the differentiable computation. The material field and equilibrium state are therefore coupled through a common finite-element incidence structure. Numerical studies show compliance comparable to conventional density-based optimization at substantially lower computational cost than a representative coordinate-based dual-field neural method. The same coupled formulation accommodates high-resolution and irregular meshes, three-dimensional structures, finite deformation, and elastoplastic response.

0.46