CS Paper Radar

Buildability Assessment of 3D-Printed Concrete Structures Using Smoothed Mohr-Coulomb Plasticity with Isotropic Hardening

Saif-Ur-Rehman, Annika Robens-Radermacher, R. J. M. Wolfs, Jörg F. Unger

cs.CE math.NA ·submitted 2026-09-07 16:03 UTC · v1

Abstract

Extrusion-based 3D concrete printing builds structural elements layer upon layer without formwork, so freshly deposited material must carry the growing weight of the structure while it is still gaining strength and stiffness. The largest number of layers that can be printed before failure, the buildability, is therefore central to process design. Its prediction rests above all on how accurately the constitutive model represents fresh concrete. Existing finite element frameworks pair gradual pre-failure hardening only with smooth yield surfaces, which leaves the Mohr-Coulomb surface that best describes fresh concrete restricted to perfect plasticity. This work combines a smoothed Mohr-Coulomb yield surface with nonlinear isotropic hardening of the cohesion, formulated in an updated Lagrangian setting with an activation field for layer deposition. Failure is identified from a tangent-stiffness eigenvalue criterion that matches the analytical self-weight buckling load of a slender wall and is insensitive to geometric imperfection. The framework reproduces the measured collapse of a printed straight wall within one layer and predicts the collapse of a hollow cylinder closer to experiment than existing frameworks. A study over six diameters and six hardening rates shows buildability peaking at intermediate diameters and rising with the hardening rate. Recording how much of its strength the material has used at failure, slender cylinders fail with much still in reserve while intermediate ones use nearly all of it. The two failure modes are therefore identified as the limits of one process rather than separate failure mechanisms.

Closest papers

Nearest neighbours by meaning across the whole index.

Influence of Extruded Filament Shape on Buildability in 3D Concrete Printing: A Geometry-Informed Deep Learning-FEM Approach

cs.CE cs.AIcs.LGmath.NA ·2026-09-03 ·Giacomo Rizzieri, Saif-Ur-Rehman, Jörg F. Unger, Annika Robens-Radermacher
similarity 0.55
Abstract · Added references

The geometric morphology of deposited filaments can significantly influence the structural performance and stability of 3D concrete-printed (3DCP) structures. However, most finite element (FEM)-based approaches for buildability assessment represent printed layers as simplified rectangles, potentially limiting predictive accuracy. This study proposes a geometry-informed modelling framework that integrates the deep-learning-based filament shape prediction tool ShapeGen3DCP with a layer-activation FEM approach to investigate the effect of realistic filament geometries on buildability. The framework generates geometry-aware numerical models directly from material and process parameters, eliminating the need for experimental filament characterization or computationally intensive fluid-flow simulations. Validation against experimental data and a parametric study of rectilinear walls demonstrate that extrusion parameters and the resulting filament geometry can significantly influence buildability predictions. Realistic filament representations are particularly important for free-flow deposition, whereas layer-pressing strategies are less sensitive to geometric simplifications. Among the investigated representations, an elliptical approximation provides an effective balance between geometric fidelity and modelling simplicity. When rectangular representations are preferred to enable regular computational meshes for faster simulations, defining their dimensions based on volume conservation improves prediction reliability compared with calibrating them using either the maximum filament width or the interlayer contact width. Overall, the proposed methodology demonstrates the importance of incorporating filament geometry into 3DCP simulations and provides practical guidance for selecting efficient and accurate geometric representations for buildability assessment.

0.19

Elastoplastic inherent strain-based topology optimization for residual stress reduction in metal additive manufacturing

cs.CE ·2026-09-07 ·Takao Miki, Jike Han, Kazuhiro Izui, Shinji Nishiwaki
similarity 0.52
Abstract · 34 pages, 17 figures, 6 tables. v2: Figures 15-17 (three-dimensional results), which were missing in v1, are now included. No other changes

This paper proposes a topology optimization method for reducing the residual stress arising in the building process of metal additive manufacturing. First, a layer-by-layer process analysis model based on an elastoplastic inherent strain method is introduced. In this model, the incremental displacement is solved anew at each layer step, and the stress history is explicitly incorporated into the constitutive equation as the stress accumulated up to the previous step, which guarantees the stress continuity across layer interfaces without introducing activation strains. Next, the design sensitivity of this analysis model is derived based on the adjoint method. Taking the pair of the stress and the equivalent plastic strain as the state variables reduces the dependency between layer steps to a one-step recurrence, and the adjoint fields are constructed as a layer-by-layer reverse sweep that reuses the coefficient tensors obtained in the forward analysis. Consequently, the cost of the sensitivity analysis scales linearly with the number of layers and remains of the same order as that of the forward analysis. An optimization problem is then formulated based on the density method to minimize the P-norm of the residual stress at the completion of the building process under the volume and final-use compliance constraints, and the derived sensitivities are verified by comparison with central finite differences. Finally, the proposed method is demonstrated through two- and three-dimensional examples of residual stress minimization under a compliance constraint. The results clarify that, under the elastoplastic analysis, the maximum residual stress is bounded by the yield surface, and the optimization therefore reduces the extent of the yielded and plastic strain accumulating regions rather than the peak stress value.

0.29

Sensitivity Hot Spot Penalization: A Robust Topology Optimization Framework against First-Order Worst-Case Perturbations

cs.CE ·2026-08-31 ·Junpeng Wang, Niels Aage, Ole Sigmund
similarity 0.46
Abstract

Deterministic topology optimization can efficiently generate high-performance structural designs, but it does not explicitly control localized fragility induced by manufacturing variations and geometric uncertainties. Such fragility often appears as stress concentrations or hinge-like deformation mechanisms. Conventional robust topology optimization can suppress these features, but typically requires multiple design realizations and substantially increased computational cost. Recent work by Sigmund et al. (2026) introduced sensitivity hot spot penalization (SHoSP), which augments the nominal objective by a smooth maximum of its sensitivities and suppresses localized fragile features at low additional cost while promoting more even stress distributions. This paper establishes a general connection between SHoSP and a first-order worst-case robust approximation under a material-mass perturbation budget using a Taylor expansion and H{"o}lder's duality. The original penalty weight is identified as a dimensionless norm-bounded perturbation budget relative to the area (2D) or volume (3D) of the design domain. This interpretation explains the suppression of sensitivity hot spots, hinge localization, and stress concentrations by limiting the maximum first-order degradation under budgeted perturbations. It is investigated for compliance minimization and compliant mechanism design. Robustness is assessed using a relaxed worst-case density perturbation and by comparing deterministic and SHoSP designs under equivalent perturbation budgets. Stress-related effects observed on structured meshes are cross-validated by stress-oriented topology optimization and body-fitted finite element analyses. Extensions to porous infill optimization, multiple load cases, and large-scale 3D examples further demonstrate the applicability and superior scalability of the SHoSP framework.

0.22

Variational r-Adaptive Cloth Simulation

cs.GR ·2026-08-18 ·Jiahao Wen, Zhen Chen, Jernej Barbič, Danny M. Kaufman
similarity 0.43
Abstract · 11 pages

We present the first r-adaptive method for simulating cloth dynamics and statics with frictional contact in modern cloth pipelines. Thin cloth requires high effective spatial resolution to reproduce wrinkles, folds, buckling, and sharp contact features. However, applying existing variational r-adaptivity to piecewise-linear shells reveals two coupled failure modes. Discretized incremental-potential (IP) optimization can become trapped in poor local minima, yielding suboptimal physical configurations. It can also lower IP artificially by collapsing elements, invalidating the finite-element approximation on which the objective relies. We address both problems with degeneracy-activated quality regularization. The regularizer remains inactive for well-shaped elements, preserving anisotropic adaptation and local densification, but becomes strong near degeneracy. It suppresses spurious low-energy basins, improves escape from suboptimal physical minima, and prevents element bunching, a cloth-specific failure in which elements progressively collapse as cloth slides across sharp contact features. For practical performance, we introduce a dynamic nonlinear solver that exploits within-timestep coherence through accelerated derivative evaluation and dynamic IPC tolerance updates for r-adaptive iterative trust-region (ITR) solves. This yields a 3-6x speedup over prior optimal ITR. Experiments on challenging frictional-contact scenarios show that, under equal vertex-count and time-budget constraints, our method achieves higher visual fidelity than fixed meshes.

0.31

Thermodynamically consistent neural constitutive models for elastoplasticity via eigen-representations

cs.CE ·2026-11-09 ·Harikrishnan Vijayakumaran, Shunyu Yin, Martin Abendroth, Miguel A. Bessa, Karl A. Kalina
theory similarity 0.43
Abstract

Neural network material models can represent yield surfaces and hardening laws with far more flexibility than classical closed-form plasticity formulations, but training such a model end-to-end through an implicit return map introduces non-trivial challenges. This work presents a thermodynamically consistent neural constitutive model for rate-independent, isotropic elastoplasticity that jointly learns a flexible yield function together with its evolution laws. For non-associative flow, the yield function extends the convex flow potential by a jointly trained additive term, which renders the model thermodynamically consistent by construction. Isotropy and convexity are enforced simultaneously across all learnable components through a permutation-invariant, spectral (eigenvalue-based) representation. Training proceeds through a backward-Euler return map, with gradients propagated by the implicit function theorem together with an eigenvalue-degeneracy-aware scheme for safe differentiation. The robustness and generality of the approach are demonstrated by reproducing known constitutive models, including non-associative flow, learning material behavior from stress--strain data extracted from a full-field finite element simulation, and capturing unknown non-associative behavior from homogenized representative volume elements of a foam. Finally, the proposed neural plasticity model is evaluated within finite element simulations to solve boundary-value-problem under plane stress.

0.27

Geometry-Based Metrics for Early-Stage Hull-Form Producibility Screening

cs.CE cs.CG ·2026-09-23 ·Andrea Serani, Kevin Maki
code/data similarity 0.42
Abstract

This paper presents a representation-aware framework for geometry-based screening of hull-form producibility at early design stages. The proposed signature combines dimensionless total and signed developability deviation with curvature-class area fractions, distributed fields, metric-specific validity, and representation provenance. These descriptors characterize surface features relevant to plate forming and developability, but are not calibrated predictors of fabrication cost, forming effort, or process feasibility. Native IGES/STEP boundary representations (BReps) are evaluated through direct differential geometry and trimmed-domain quadrature, whereas triangulated surfaces use discrete curvature recovery and area-weighted aggregation. Analytical and semi-analytical controls verify the formulation, while matched-face BRep-to-mesh tests assess discrete curvature recovery. Application to DTMB 5415, KCS, JBC, and KVLCC2M shows that curvature intensity and areal extent provide complementary information and that derivative-based outcomes can be representation sensitive. KCS, for example, exhibits approximately 24% greater developability deviation than DTMB 5415, while double-curved regions occupy 72.9% of its valid surface versus nearly the entire DTMB valid surface. The resulting quantities provide an early geometric screening layer for subsequent use as objectives, constraints, surrogate responses, or design-space features. HullProd, the companion open-source software, implements the signature, distributed fields, validity, and provenance.

0.26

Reliability Assessment of FRP-RC Columns Using AK-MCS with a Piecewise Two-Branch Approach

cs.CE stat.APstat.CO ·2026-10-25 ·Arndt Goldack, Richard Koehler, Ahmed Usama Syed
similarity 0.42
Abstract · 22 pages, 5 figures

Slender concrete columns reinforced with fiber-reinforced polymer (FRP) bars fail at medium to high axial load levels either by concrete crushing or by loss of stability, while the tensile strains in the reinforcement remain far below the rupture strain. Each non-linear finite element (FE) analysis yields only the capacity of the governing failure mode, and the governing mode changes over a broad zone in which both capacities are nearly equal. Both characteristics conflict with active-learning Kriging-assisted Monte Carlo simulation (AK-MCS), which assumes a single, smooth limit-state function. This paper proposes a piecewise, two-branch AK-MCS framework in which each failure mode is represented by its own Kriging model, trained only on the FE analyses in which that mode governs, and the governing prediction is the minimum of both. Safeguards against data starvation keep rarely governing branches usable. After convergence, additional FE analyses are placed based on a leave-one-out calibration check and on the width of the confidence interval on the reliability index. A design-point search on the surrogate and importance sampling at the design points provide the reliability index even where direct Monte Carlo simulation finds no failure. For an FRP-reinforced concrete column example with mixed failure, 79% and 62% of the training points lie near the mode boundary. The reliability index from the design-point search agrees with the Monte Carlo estimate to within 0.05, and an FE analysis at the design point confirms the surrogate to within 0.6%.

0.29

Towards end-to-end co-design for one-shot printable task-specific soft robots

cs.RO ·2026-11-02 ·James Wood, André Farinha, Will Browne, Josh Pinskier, Krishna Manaswi Digumarti
similarity 0.42
Abstract

Soft robot co-design methods can jointly optimise morphology and control, but the resulting designs are often difficult to manufacture, while manufacturable approaches typically restrict actuator placement or require manual assembly. We present a simulation-based co-design framework that jointly optimises material distribution, pneumatic actuator placement and orientation, and control, while producing designs that can be fabricated monolithically using fused deposition modelling. The framework uses a differentiable 2D plane-stress Material Point Method simulator, incorporating an experimentally validated material model and an empirically derived surrogate model of a 3D-printed inflatable actuator. We demonstrate gradient-based optimisation soft robotic arms for prescribed tip trajectories. Optimised designs are transferred directly from simulation to one-shot monolithic FDM fabrication, with integrated actuators and no post-assembly. Physical experiments demonstrate that the resulting arms reproduce the behaviour predicted in simulation. This framework provides a path from task-level objectives to physically realisable soft robots while retaining substantial freedom over both morphology and actuation.

0.14