CS Paper Radar

Toward 3D Printable Non-Planar Electroadhesive Structures for Active Anchoring

Mostafa A. Atalla, Carol R. Derla, Pep Canyelles Pericàs, Gijs Krijnen

cs.RO ·submitted 2026-09-16 14:10 UTC · v1
publishedbenchmark

Abstract

This paper investigates multi-material 3D printing as a method to fabricate non-planar structures with 3D-printed electrode patterns for electroadhesion. We printed flat electroadhesion pads as a planar benchmark and cylindrical pads as a non-planar demonstration, with conductive interdigitated electrodes 3D printed as part of the structure. Normal-force measurements showed voltage-controlled modulation in both geometries. At 3 kV, the flat pads generated approximately 0.11-0.13 N, while the cylindrical pads reached approximately 0.16 N at 5 N preload. These results demonstrate a step toward printed parts with built-in, electrically controlled adhesion and friction, beyond conventional planar electroadhesion pads.

Comment
Accepted for publication in the proceedings of the IEEE SENSORS 2026

Closest papers

Nearest neighbours by meaning across the whole index.

Print-Aware Synthesis and Physical Design Methodologies for 3D-Printed Microfluidic Biochips

cs.ET ·2026-08-17 ·Yushen Zhang, Tsun-Ming Tseng, Ulf Schlichtmann
published similarity 0.55
Abstract · Accepted for publication in the 2026 IEEE Computer Society Annual Symposium on VLSI (ISVLSI)

Microfluidic devices are widely used in diagnostics, chemical synthesis, and biological analysis, but their development often depends on complex fabrication and design processes. Resin-based three-dimensional (3D) printing has emerged as a promising alternative to conventional microfabrication because it enables low-cost, rapid prototyping of complex multi-layer structures. However, the practical realization of 3D-printed microfluidic biochips remains challenging due to manual and expertise-intensive design workflows, the rigid nature of commonly used printing materials, and fabrication inaccuracies such as over-curing that distort internal features and may block narrow channels. In this paper, we present a cohesive design automation framework for 3D-printed microfluidics that addresses these challenges across both device design and fabrication. The framework combines interactive design tools, automated synthesis methods for functional 3D microfluidic devices, techniques for developing low-cost 3D-printed mixers, and design-for-manufacturing strategies to improve print fidelity on low-cost resin printers.

0.32

AI-guided robotic in situ fabrication of curvature- and tissue-adaptive wireless bioelectronics

cs.RO ·2026-11-13 ·Hiroyuki Tetsuka, Jiaju Ma, Naomi Kumano, Minoru Hirano
similarity 0.54
Abstract

Personalized bioelectronic devices for wound therapy require not only conformal fabrication on complex body surfaces but also functional adaptation of their electrical characteristics to individual wound geometries. Here, we present an AI-guided robotic in situ printing platform for fabricating wireless wound electrotherapy devices directly on transparent wound dressings. The system integrates a 3D vision camera, a six-degree-of-freedom robotic arm, direct-ink-writing, and geometry-aware RF design optimization. AI-based wound segmentation is used to determine wound dimensions and local surface curvature, while the reconstructed three-dimensional geometry is incorporated into the electromagnetic design of the receiving coil and interdigitated electrodes. In contrast to conventional approaches that use surface geometry only for trajectory generation, the proposed method accounts for both anatomical curvature and tissue dielectric loading to compensate for geometry-induced shifts in resonant behavior. A printable silver ink was characterized in terms of rheology, dimensional reproducibility, electrical resistance, and electromechanical stability, and was used to fabricate multilayer wireless devices directly on curved polyurethane dressings. Wireless power transfer, impedance characteristics, and electric-field delivery were evaluated experimentally and numerically. Finally, robotic in situ fabrication was demonstrated on an anthropomorphic tissue-equivalent forearm phantom, where the measured dielectric properties of the phantom were incorporated into the RF optimization, enabling resonant operation near the target frequency of 25 MHz. This work establishes a perception-to-design-to-fabrication framework for geometry-adaptive wireless bioelectronics and provides a technological foundation for future physical-AI-enabled manufacturing of personalized on-body electrotherapy devices.

0.23

Direct-Ink-Writing of Soft Thin Film Force-Sensitive Resistors with Velostat and Printed-Carbon Sensing Elements

cs.RO ·2026-11-12 ·Mostafa Mo. Massoud, Paulo H. T. F Alves, Timothy Kennedy, Jacqueline Libby
publishedunusual similarity 0.51
Abstract · 12 pages, 18 figures, to be published in: IEEE Sensors

Flexible resistive force sensors are useful for wearable, rehabilitation, and human--machine interfaces, but their performance depends on sensing-material architecture and fabrication. This work presents a parameterized Voltera NOVA-based direct-ink-writing workflow using printed silver electrodes with multilayer Velostat sensing elements on PET and TPU substrates, together with an exploratory fully printed carbon architecture. Velostat sensors containing 1, 2, 4, and 6 sensing layers exhibited strongly nonlinear force--voltage responses, with the greatest sensitivity at low forces. Best-fit straight-line $R^2$ values ranged from 0.475 to 0.641, area-based hysteresis from 3.90\% to 7.47\%, and 5-min voltage drift from 1.9\% to 7.3\%, with no consistent monotonic relationship between layer count and these metrics. Selected PET6 and TPU6 devices showed less than 0.05~V change in peak output between the first and final 100 cycles of a 10,000-cycle test. Printed-carbon devices demonstrated the feasibility of a more fully printed architecture, but configurations with six or fewer layers saturated below approximately 0.5~N or were nonfunctional, while the eight-layer device responded primarily below approximately 2~N. These results establish the feasibility of the printed-electrode Velostat workflow while identifying printed sensing materials as a key area for further development.

0.37

X-Hinges: 3D Printing Self-Sensing Compliant Mechanisms for Continuous and Multi-DOF Motion Sensing

cs.HC ·2026-09-10 ·Xiang Chang, Haiyang Yan, Stefanie Mueller, Jiaji Li
top venue similarity 0.51
Abstract · Accepted at ACM UIST 2026. 15 pages, 24 figures. Author's accepted manuscript

We present X-Hinges, a design and fabrication method for self-sensing compliant mechanisms based on multi-material FDM 3D printing. By co-printing two conductive filaments of different conductivities within a compliant body, we embed resistive sensing elements directly during fabrication without post-assembly, enabling continuous motion sensing across multiple degrees of freedom in a single print. The structure supports three degrees of freedom, each equipped with a dedicated sensing element configuration for multi-DOF motion estimation. We develop a precision data acquisition system and data-driven regression models that enable continuous, real-time motion sensing. We also introduce an interactive design tool for customizing the geometry, mechanical properties, degrees of freedom, and sensing configurations of X-Hinges. The tool also supports augmenting existing 3D models with self-sensing structures, endowing ordinary objects with continuous multi-DOF sensing capabilities. Finally, we present a set of application examples demonstrating the capability of X-Hinges for fabricating personalized interactive interfaces.

0.47

Low Clearance Hinge Joint Mechanism Based on 3D Printing on Sheet Fabrication Methodology

cs.RO ·2026-09-14 ·Jaehyung Jang, Euibin Shin, Allison M. Okamura, Jee-Hwan Ryu
similarity 0.48
Abstract · 5 pages, 8 figures

This paper presents a low-clearance hinge joint mechanism based on the 3D printing on sheet fabrication method. This approach simplifies the fabrication of hinge mechanisms and overcomes limitations of conventional origami manufacturing by eliminating the need for adhesives commonly used during assembly, making it suitable for robots at the tens-of-centimeters scale. The advantages and disadvantages of three types of hinge joint mechanisms are compared, and a hinge joint that can be designed with low clearance for various facet thicknesses is selected. Based on the selected hinge joint, the twisting angle and bending force are analyzed, leading to the implementation of a clearance of 0.1 mm. Torsional resistance is experimentally evaluated to measure the torque required for twisting caused by plastic deformation and clearance. The results show that the torque associated with plastic deformation is sufficient to constrain the undesired degrees of freedom of the hinge joint, while the torque required for twisting due to clearance is minimal. Based on the analyzed data, the proposed hinge joint mechanism is applied to a 3-degree-of-freedom delta robot manipulator, demonstrating precise motion with low clearance.

0.25

PHD-Hand: A Printable Humanoid Dexterous Hand with Linkage-Driven 3-DOA Digits

cs.RO cs.AI ·2026-10-21 ·Neel Adwani, Muhaiminul Islam Akash, Saffia Ouali, Ethan Liu, Cong Wang
published similarity 0.43
Abstract · Submitted and Accepted at IEEE-RAS International Conference on Humanoid Robots (Humanoids 2026). 8 pages. Supplementary video: https://lnkd.…

Currently, dexterous humanoid robot hands are widely considered the final hardware bottleneck that hampers generalist robots from physically assisting people at home and work. As conventional tendon-driven designs suffer from high cost, demanding maintenance, poor reliability, and short durability, alternative linkage-driven designs have increasingly gained attention. Despite their potential to avoid the weaknesses of tendon-driven hands, integrating multiple degrees of actuation (DOA) in a single digit with linkage drivetrains is a challenge for design and fabrication. Only a few studies have managed to present functional humanoid hands that are completely linkage-driven and have at least three DOAs per digit without compromising actuator placement and other design preferences. Our work introduces a new linkage-driven hand featuring a unique flexure hinge. Together with elastic drive rods made of spring steel, the linkage drivetrains are significantly simplified. Unlike other linkage-driven designs of similar dexterity, our design does not require many miniature moving parts. As a result, the hand can be fabricated easily with a budget 3D printer. This not only significantly lowers the barrier to entry for using and developing dexterous humanoid robot hand functions, but also allows the hands to be sized much closer to regular human hands. The design offers desirable kinematic advantages as well. A prototype is evaluated for grasping and object manipulation. In addition, this paper presents our latest findings on kinematics and control of the hand.

0.25

One Print, Many Moves: Monolithic Origami-inspired Folding Actuator for Composable Soft Multi-DoF Systems

cs.RO ·2026-09-01 ·Jaehyung Jang, Zhenish Zhakypov, Jasmin Elena Palmer, Melissa Klein, Jee-Hwan Ryu +1 more
similarity 0.43
Abstract · 26 pages, 7 figures

Conventional soft robot actuators excel in compliance, but their uncontrolled deformations compromise accuracy and hinder scaling to multi-degree-of-freedom (DoF) systems. We introduce a MONOlithic ORIGAMI-inspired soft folding actuator design (MONORIGAMI) that establishes a design strategy based on spatially programmed stiffness anisotropy to preserve material compliance along desired folding directions while selectively restricting deformation in unwanted directions. The actuator leverages stiffness tiers based on material thickness, patterned in an origami-inspired geometry with facets and creases, converting unconstrained soft deformation into accurate, repeatable, and composable folding motions without additional reinforcements. The design is fully 3D-printable through a single-material, single-print process that requires no assembly. Each actuator serves as a scalable motion primitive, and linking and orienting multiple actuators mechanically programs multi-DoF trajectories. Using the same fundamental module, we demonstrate three 3D-printed soft multi-DoF robotic systems spanning distinct application domains: (1) a compact 4-DoF wearable haptic device for high-fidelity cutaneous feedback in virtual reality (VR), (2) a 3-DoF joystick for kinesthetic feedback in teleoperation, and (3) a modular robotic gripper capable of underwater operation with geometry-encoded grasp trajectories. These systems demonstrate the module's capabilities for compact multi-axis integration, controlled physical interaction, and geometry-programmed operation across different environments. Together, these results show that MONORIGAMI provides a general, composable, accessible, reliable, and scalable platform for high-precision soft multi-DoF robotics, addressing long-standing limitations in both soft actuator design and fabrication.

0.14

Tactile Sensing Array for Multi-Phalanx Sensing in Humanoid Hands

cs.RO cs.ET ·2026-09-24 ·Neel Adwani, Muhaiminul Islam Akash, Rituja Bhattacharya, Cong Wang
publishedhot direction similarity 0.43
Abstract · Accepted to be presented at IROS Workshop Touch2Action

Humanoid hands require tactile feedback across the whole finger, not just the fingertip, to grasp and manipulate objects properly. Vision and proprioception alone cannot reliably provide this information, particularly when the hand's own fingers occlude the camera's view of the grasp. We present a low-cost tactile array for a humanoid finger, made from Velostat and conductive tape. The fingertip carries seven contact points including a 2x3 matrix wrapped across its front, left, and right faces, and a separate contact point at the tip. The proximal and middle phalanges each carry a single front-facing contact line. We measure the sensor's hysteresis and recovery time after release, through repeated loading and press-release tests. We also test a compliant, 3D-printed contact structure with a gap and a bump, inspired by similar designs in prior work, and show it cuts recovery time by 74% compared to a flush-contact baseline. We then show the sensor can produce distinct activation patterns for different contact geometries (flat, edge, corner) at the fingertip, and that it registers contact across all three phalanges during a grip. Finally, we discuss the limits of our fabrication changes and point to software-based compensation as a promising way to more directly fix the remaining hysteresis in the future.

0.40