CS Paper Radar

Direct-Ink-Writing of Soft Thin Film Force-Sensitive Resistors with Velostat and Printed-Carbon Sensing Elements

Mostafa Mo. Massoud, Paulo H. T. F Alves, Timothy Kennedy, Jacqueline Libby

cs.RO ·submitted 2026-11-12 03:50 UTC · v1
publishedunusual

Abstract

Flexible resistive force sensors are useful for wearable, rehabilitation, and human--machine interfaces, but their performance depends on sensing-material architecture and fabrication. This work presents a parameterized Voltera NOVA-based direct-ink-writing workflow using printed silver electrodes with multilayer Velostat sensing elements on PET and TPU substrates, together with an exploratory fully printed carbon architecture. Velostat sensors containing 1, 2, 4, and 6 sensing layers exhibited strongly nonlinear force--voltage responses, with the greatest sensitivity at low forces. Best-fit straight-line $R^2$ values ranged from 0.475 to 0.641, area-based hysteresis from 3.90\% to 7.47\%, and 5-min voltage drift from 1.9\% to 7.3\%, with no consistent monotonic relationship between layer count and these metrics. Selected PET6 and TPU6 devices showed less than 0.05~V change in peak output between the first and final 100 cycles of a 10,000-cycle test. Printed-carbon devices demonstrated the feasibility of a more fully printed architecture, but configurations with six or fewer layers saturated below approximately 0.5~N or were nonfunctional, while the eight-layer device responded primarily below approximately 2~N. These results establish the feasibility of the printed-electrode Velostat workflow while identifying printed sensing materials as a key area for further development.

Comment
12 pages, 18 figures, to be published in: IEEE Sensors

Closest papers

Nearest neighbours by meaning across the whole index.

VecTile: A Low-Cost Flexible Tactile Array for 3-DoF Force Sensing

cs.RO ·2026-10-22 ·Jian Hou, Xin Zhou, Adam J. Spiers
similarity 0.52
Abstract · 8 pages, 8 figures. Submitted to IEEE International Conference on Robotics and Automation (ICRA) 2027

Tactile sensing provides robots with contact information difficult to obtain from vision alone. Shear force is particularly important for understanding tangential contact, guiding corrective motions, and maintaining grasp stability, yet flexible and low-cost tactile arrays often measure only normal force. We introduce VecTile, a low-cost, 6 mm thin, flexible tactile array capable of three-axis force sensing. VecTile combines a piezoresistive layer with passive silicone nubs that convert normal and shear forces into distinguishable pressure patterns. The sensor can be fabricated in-house without specialized equipment. The complete system costs less than 35 USD for a 4x4 array. We validate the sensing mechanism through finite element analysis and hardware experiments. In controlled single-taxel tests over 1-5 N normal force and up to 1.5 N shear force, VecTile achieves root-mean-square errors of 0.39 N and 0.16 N for normal and shear forces. A VecTile calibrated while flat retains accuracy when curved, while a five-minute manual calibration is sufficient for practical use. Two applications demonstrate its utility. First, shear readings are sensitive enough to stop a sharp scalpel from puncturing a balloon after contact. Second, the sensor substantially improves Diffusion Policy-guided power-plug insertion. All designs and code will be released upon paper acceptance. Project website: https://jiannnh.github.io/VecTile/.

0.20

Toward 3D Printable Non-Planar Electroadhesive Structures for Active Anchoring

cs.RO ·2026-09-16 ·Mostafa A. Atalla, Carol R. Derla, Pep Canyelles Pericàs, Gijs Krijnen
publishedbenchmark similarity 0.51
Abstract · Accepted for publication in the proceedings of the IEEE SENSORS 2026

This paper investigates multi-material 3D printing as a method to fabricate non-planar structures with 3D-printed electrode patterns for electroadhesion. We printed flat electroadhesion pads as a planar benchmark and cylindrical pads as a non-planar demonstration, with conductive interdigitated electrodes 3D printed as part of the structure. Normal-force measurements showed voltage-controlled modulation in both geometries. At 3 kV, the flat pads generated approximately 0.11-0.13 N, while the cylindrical pads reached approximately 0.16 N at 5 N preload. These results demonstrate a step toward printed parts with built-in, electrically controlled adhesion and friction, beyond conventional planar electroadhesion pads.

0.37

A Monolithic Force-Proprioception Soft Acutuator Enabled by Single-Material 3D printing

cs.RO ·2026-09-21 ·Nan Huang, Lele Liu, Junfeng Lu, Yipan Zhu, Jiansheng Dai +1 more
similarity 0.50
Abstract

Pneumatic proprioceptive actuators integrate actuation and sensing for soft robots that attract interest due to functional potential. Existing approaches often suffer from assembly errors or stress concentrations caused by heterogeneous materials. In this work, we propose the Monolithic Force-Proprioception Soft (MFPS) design and fabrication method that integrates an Asymmetric Origami Bending (AOB) chamber and a Force-Proprioception Soft (FPS) sensor with single material through one-step Fused Deposition Modeling (FDM) fabrication. Based on the resistance response to strain of conductive thermoplastic polyurethane (TPU), we design and analyze the structure of the FPS sensor, and conduct parametric analysis on the sensing characteristics. The FDM fabrication parameters of the MFPS actuator are analyzed, followed by actuator fabrication and characterization of the actuation and proprioception performance. Experimental results show that the MFPS actuator achieves a bending angle of 40°, an output force of 12.5 N, and a resistance change of 26.9% as the applied external force increased from 0 to 45 N. A two-finger force-proprioception gripper is developed based on the MFPS actuator. The grasping and force-proprioception capabilities are experimentally validated, proving that the MFPS design method provides a new approach for the development of self-sensing actuators.

0.20

X-Hinges: 3D Printing Self-Sensing Compliant Mechanisms for Continuous and Multi-DOF Motion Sensing

cs.HC ·2026-09-10 ·Xiang Chang, Haiyang Yan, Stefanie Mueller, Jiaji Li
top venue similarity 0.50
Abstract · Accepted at ACM UIST 2026. 15 pages, 24 figures. Author's accepted manuscript

We present X-Hinges, a design and fabrication method for self-sensing compliant mechanisms based on multi-material FDM 3D printing. By co-printing two conductive filaments of different conductivities within a compliant body, we embed resistive sensing elements directly during fabrication without post-assembly, enabling continuous motion sensing across multiple degrees of freedom in a single print. The structure supports three degrees of freedom, each equipped with a dedicated sensing element configuration for multi-DOF motion estimation. We develop a precision data acquisition system and data-driven regression models that enable continuous, real-time motion sensing. We also introduce an interactive design tool for customizing the geometry, mechanical properties, degrees of freedom, and sensing configurations of X-Hinges. The tool also supports augmenting existing 3D models with self-sensing structures, endowing ordinary objects with continuous multi-DOF sensing capabilities. Finally, we present a set of application examples demonstrating the capability of X-Hinges for fabricating personalized interactive interfaces.

0.47

Effect of Twisted-Yarn Architecture on Pressure and Proximity Sensing Characteristics of Textile Capacitive Sensors for Robotic Skin

cs.RO physics.ins-det ·2026-08-14 ·Ishtia Zahir, Eslam Saleh, Maryam Rezayati, Güunter Grabher, Gaffar Hossain
similarity 0.50
Abstract · 10 pages. Submitted to IEEE Transactions on Instrumentation and Measurement

Textile-integrated capacitive sensors offer flexible and conformable tactile sensing for wearable electronics and human-robot interaction; however, the influence of yarn-level architecture on capacitive transduction characteristics remains insufficiently quantified. This work presents a textile capacitive sensing platform based on silver-coated yarns coated with polydimethylsiloxane and assembled into one-, two-, and four-layer twisted configurations. The influence of effective electrode overlap area and inter-fiber separation on the capacitive response is systematically investigated, enabling architecture-dependent tuning of pressure and proximity sensing characteristics. Pressure was calculated using the localized single-fiber contact area, corresponding to stresses of 0.4-3.9 MPa. Increasing the layer number improved mechanical strength and sensing performance: elongation at break increased from 37.5% to 62.5% and 85.0%, while the maximum load increased from 23.3 to 42.7 and 89.7 N. Sensitivity increased with layer number and frequency, reaching 0.1331 MPa$^{-1}$ for the four-layer sensor at 100 kHz. The four-layer configuration also exhibited low hysteresis, minimal thermal drift from 25 to 90 $^\circ$C, and stable operation over 15,000 cycles. Proximity detection ranges of 60, 50, and 40 mm were obtained for the one-, two-, and four-layer sensors, respectively, revealing an architecture-dependent sensitivity-range trade-off. A 4$\times$4 textile sensing array enabled spatial contact mapping, while robotic-arm integration demonstrated real-time touch and proximity detection with an end-to-end robotic system latency (from detection to robot reaction) of 403 ms. The results establish yarn architecture as a tunable design parameter governing the measurement characteristics of textile-integrated capacitive sensing systems.

0.12

Layered e-skin for Shear Sensing

cs.RO ·2026-09-18 ·Qingzheng Cong, Alexis W. M. Devillard, Abu Bakar Dawood, Xinxin Zhang, Wen Fan +5 more
similarity 0.46
Abstract · 8 pages, 5 figures. Submitted to IEEE Sensors Journal

This paper presents a stacked two-layer force-sensing resistor (FSR) array designed for robotic fingertips that combines high-resolution pressure mapping with shear-force estimation. A compliant lattice elastomer spacer converts shear loading into a measurable inter-layer displacement, producing relative center-of-pressure (CoP) shifts between layers. A physics-based moment balance links inter-layer CoP displacement to shear force, while an end-to-end CNN--GRU model captures nonlinear effects from load-dependent compression and contact redistribution. This model, with both layers as input, achieves coefficients of determination $R^2 = 0.914$ for $F_x$ and $R^2 = 0.944$ for $F_y$, consistently outperforming single-layer baselines for shear-force estimation. Robotic manipulation experiments show that, for contact-motion tracking, the deep layer tracks the translation and rotation imposed by the robot arm, whereas the superficial layer tracks the slip at the contact surface. Transient changes in the difference between the total pressure responses of the two layers provide the best slip-event detection performance among the tested cues. These results demonstrate that two-layer FSR arrays can provide three-axis force estimation, contact-motion tracking, and slip-event detection beyond conventional normal-force sensing.

0.32

A Durable Vision-Based Tactile Fingertip for Robotic Manipulation

cs.RO ·2026-08-25 ·F. Richard Cottrell, Megha H. Tippur, Edward H. Adelson
similarity 0.45
Abstract · 22 pages, 20 figures

Currently available commercial vision-based tactile sensors provide rich contact information but remain vulnerable to abrasion and repeated concentrated loading, limiting their use in demanding robotic applications. This work presents a durable tactile fingertip comprising a soft silicone gel with a nonpigmented, textured, thin thermoplastic-polyurethane protective film and a replaceable sensing cartridge. Durability was evaluated using two accelerated laboratory procedures: a rotating-drum sanding test and a repetitive probe test applying 39.2 N (4.0 kgf) at 45 cycles per minute. Under the defined sanding conditions, the developed sensor reached the protective-film rupture endpoint after approximately 2-3 hours. During repetitive probe testing, all nine developed sensors remained functionally usable when testing was discontinued: seven after 5 days, one after 6 days, and one after 8 days. Commercial GelSight Mini and DIGIT specimens exhibited initial surface-film rupture after approximately 24-30 seconds of sanding and 25-35 minutes of repetitive loading. Damage to the developed sensor progressed gradually and produced little interference with tactile imaging at the test endpoints. These observations establish durability improvements of more than two orders of magnitude under the defined accelerated conditions. Combining increased durability, gradual degradation, and rapid cartridge replacement offers a practical approach to maintainable vision-based tactile sensing for demanding robotic applications.

0.27

Simultaneous Digital Communication and Deformation Sensing over a Single Stretchable Interconnect

cs.ET cs.HCphysics.app-ph ·2026-08-26 ·Yuji Isano, Hiroki Ota
similarity 0.45
Abstract · 41 pages, 4 figures, 18 supplemental figures, will be submitted to Advanced Functional Materials

Stretchable hybrid electronics integrate rigid solid-state electronics with stretchable materials and structures to achieve both high deformability and stable electronic performance. However, most existing systems treat stretchability only as a mechanical attribute without exploiting device deformation to encode its own mechanical state. This problem arises from adapting conventional rigid circuit architectures to stretchable substrates, affording a loss in compatibility with the sensors required for strain measurement. This study addresses this issue by proposing a communication-integrated deformation sensing architecture for stretchable hybrid devices. In the proposed approach, standard universal asynchronous receiver-transmitter digital signals transmitted between rigid nodes are amplitude-modulated by strain-induced resistance changes in stretchable liquid metal interconnects. By reading both amplitude changes and digital patterns, the system enables simultaneous digital communication and self-deformation sensing without requiring additional stretchable sensing elements. The architecture is demonstrated in a multi-node system and applied to wearable sensing and self-deformation mapping devices. By extending the integration of rigid circuits and soft elements from the hardware level to the system level, this study provides a novel design paradigm for stretchable electronic systems that inherently utilize their own deformation as functional information.

0.32