CS Paper Radar

When LiDAR Fades, Radar Takes Over: LiDAR Reliability-Aware Adaptive Localization Under Airborne Obscurants

Moumita Mukherjee, Avijit Banerjee, Anton Koval, George Nikolakopoulo

cs.RO ·submitted 2026-10-09 16:04 UTC · v1

Abstract

LiDAR-inertial odometry (LIO) is widely used for real-time localization and mapping, but its reliability can degrade substantially in subterranean environments affected by smoke, dust, and other airborne obscurants, whereas radar remains comparatively robust. This article presents a one-class temporal learning framework for LiDAR degradation detection and reliability-aware localization under such conditions. A broad set of degradation-sensitive cues, including spatial, cross-modal, geometric/motion, intensity, and measurement-recency features, is evaluated to characterize changes in LiDAR sensing quality. Their temporal evolution is modelled over sliding windows using an LSTM autoencoder trained exclusively on nominal operation, enabling deviations from healthy sensor behaviour to be detected without requiring labelled degradation data. The resulting LiDAR reliability estimate governs adaptive selection between LIO and radar inertial odometry (RIO), retaining LIO during reliable sensing and transferring localization authority to RIO when degradation is detected. The framework is evaluated using real-world ground robot data collected in GNSS-denied subterranean tunnels under nominal and dense-smoke conditions. Experimental results demonstrate degradation detection, adaptive modality switching, and continued localization output under severe LiDAR degradation. A feature family ablation study further shows that a reduced feature representation can improve degradation-aware localization performance in the evaluated dense-smoke scenarios, highlighting the importance of feature parsimony in one-class sensor degradation detection. The code will be released as open source to support reproducibility and further research.

Closest papers

Nearest neighbours by meaning across the whole index.

Resilient Decentralized Radar-LiDAR-Inertial Odometry in Challenging Subterranean Environments

cs.RO ·2026-10-23 ·Moumita Mukherjee, Avijit Banerjee, Anton Koval, George Nikolakopoulos
similarity 0.74
Abstract

Accurate localization in GPS-denied and visually degraded environments affected by smoke, dust, or fog remains a critical challenge for autonomous systems. While LiDAR provides high-resolution spatial perception, its performance deteriorates under particulate occlusion. In contrast, frequency-modulated continuous-wave (FMCW) radar offers robustness under such conditions but suffers from sparse measurements and outliers. This article presents a resilient decentralized LiDAR Radar Inertial Odometry (LRIO) framework that fuses the complementary strengths of LiDAR, radar, and inertial sensing to achieve robust pose estimation in challenging subterranean environments. At the core of the framework is an Adaptive Residual Thresholding (ART) mechanism that autonomously detects temporal sensor degradation and selectively adjusts the fusion process to minimize unreliable measurements. Building on this, a Robust Error-Tolerant Optimal Information Filter (RETOIF) is employed within a decentralized fusion architecture to integrate LiDAR-inertial and multiple radar-inertial odometry estimates in a fault-aware manner, enhancing resilience to environmental disturbances and intermittent sensor failures. The proposed framework is evaluated using real-world sensor data collected in GPS-denied subterranean tunnels under smoke-free and smoke-degraded conditions. In the smoke-free experiment, the proposed RETOIF framework achieves a root mean square localization error (RMSE) of 2.1733, compared with 2.9929 for the conventional centralized LRIO approach, corresponding to a 27.4\% reduction in RMSE. Experimental results further demonstrate the framework's ability to maintain pose estimation under smoke-induced sensor degradation, highlighting its potential for resilient autonomous navigation and mapping in challenging subterranean environments.

0.05

FIRE-LIVWO: Robust LiDAR-Inertial-Visual-Wheel Odometry via Failure-Immune mmWave Radar Enhancement

cs.RO ·2026-09-04 ·Kun Hu, Menggang Li, Kaidi Wu, Zhiwen Jin, Yingjie Zhao +3 more
publishedcode/data similarity 0.70
Abstract · Accepted by IROS 2026.The project website is "https://kj-falloutlast.github.io/FIRE-LIVWO"

Achieving robust SLAM in large-scale underground coal mines with complex structures and severe degeneracies remains highly challenging. Dense smoke and dust cause substantial loss of visual information and degrade LiDAR point-cloud features, while long, self-similar corridors induce geometric degeneration, leading to pronounced odometry drift. To address these issues, we propose FIRE-LIVWO: Failure-Immune mmWave Radar-Enhanced LiDAR-Inertial-Visual-Wheel Odometry, a tightly coupled multi-modal odometry framework based on an iterated error-state Kalman filter (IESKF). The framework fuses 4D mmWave radar, LiDAR, and visual features within a unified VoxelMap and jointly constructs LiDAR-radar point-to-plane residuals and sparse visual photometric residuals. In smoke-filled environments, we exploit the strong penetration of 4D mmWave radar and introduce pointwise Doppler velocity constraints to preserve state observability. In geometrically degenerate corridors, we tightly couple wheel odometry using non-holonomic constraints (NHC) and online lever-arm compensation to reduce drift. Our central contribution is a degeneration detection and adaptive fusion model switching strategy grounded in geometric and visual observability analysis, which quantifies observability online and dynamically adjusts modality weights. Real-world experiments in underground coal mines demonstrate that FIRE-LIVWO accurately identifies failure boundaries, enabling reliable modality switching under extreme conditions. Compared with baselines, it achieves superior accuracy and robustness (average localization error of 5.677m). We open source our code on Github to benefit the robotics community.

0.41

NM-LIO: Multiple LiDAR-Inertial Odometry Addressing LiDAR Measurement Noise Discrepancy

cs.RO ·2026-10-03 ·Gunhee Shin, Seungjae Lee, Minho Oh, Dongkyu Lee, Jaeyoung Lee +2 more
published similarity 0.68
Abstract · 10 pages, 3 figures, 1 table. Published in the International Conference on Robot Intelligence Technology and Applications (RiTA 2024)

Multiple LiDAR-inertial odometry methods have been widely applied in robotic applications owing to their enhanced accuracy and reliability. However, adopting multiple LiDAR systems can be challenging due to the discrepancies in measurement noise across different LiDARs. Existing methods have typically overlooked the noise discrepancies, which can significantly affect accuracy. In this paper, we propose Noise-aware Multiple LiDAR-Inertial Odometry (NM-LIO) that addresses the noise discrepancies. We integrate a noise model to quantify the measurement noise of each LiDAR. Additionally, we estimate the uncertainty of the residuals based on the measurement noise, allowing the measurement model to capture the noise discrepancies. Our proposed method is evaluated on a public multiple LiDAR dataset and compared with state-of-the-art methods. The experimental results demonstrate that the proposed method can accurately estimate the odometry in various environments by accounting for the noise discrepancies.

0.27

SUPER ODOMETRY 2.0: Resilient Odometry via Hierarchical Adaptation

cs.RO ·2026-08-26 ·Shibo Zhao, Sifan Zhou, Yuchen Zhang, Ji Zhang, Chen Wang +2 more
publishedhighly cited similarity 0.68
Abstract

Resilient and robust odometry is crucial for autonomous systems operating in complex and dynamic environments. Existing odometry systems often struggle with severe sensory degradations and extreme conditions such as smoke, sandstorms, snow, or low-light conditions, threatening both the safety and functionality of robots. To address these challenges, we present Super Odometry, a sensor fusion framework that dynamically adapts to varying levels of environmental degradation. Super Odometry employs a hierarchical structure to integrate four core modules from lower-level to higher-level adaptability including adaptive feature selection, adaptive state direction selection, adaptive engine selection, and a novel learning- based inertial odometry. The inertial odometry, trained on over 100 hours of heterogeneous robotic platforms, captures comprehensive motion dynamics. Super Odometry elevates the inertial measurement unit (IMU) to equal importance with camera and LiDAR within the sensor fusion framework, providing a reliable fallback when exteroceptive sensors fail. Super Odometry has been validated across 200 kilometers and 800 operational hours on a fleet of aerial, wheeled, and legged robots, under diverse sensor configurations, environmental degradation, and aggressive motion profiles. It marks an important step towards safe and long-term robotic autonomy in all-degraded environments.

0.69

Dynamic-LIVO: A Dynamic-Aware LiDAR-Inertial-Visual Odometry System Using Spatio-Temporal Normals

cs.RO ·2026-09-16 ·Zhixin Zhang, Samuel Ahiwe, Matthew Hale, Liang Zhao, Pawel Ladosz
similarity 0.67
Abstract · 8 pages conference

This paper proposes Dynamic-LIVO, a dynamic-aware LiDAR-Inertial-Visual Odometry (LIVO) system for robust state estimation and static colored mapping in dynamic environments. Dynamic-LIVO employs Spatio-Temporal (S-T) normal analysis to identify dynamic LiDAR points and propagates the resulting classification to both LiDAR-inertial and visual-inertial updates, preventing dynamic LiDAR measurements and their associated visual observations from affecting state estimation and mapping. However, S-T normal estimation can be unreliable in newly observed and spatially sparse regions due to insufficient spatio-temporal observations. To address this issue, we introduce a time-delayed S-T normal estimation strategy that defers the classification of insufficiently constrained points and re-evaluates them as additional observations become available. This strategy improves dynamic classification reliability while preserving valid static points for map construction. Extensive experiments on public and self-collected datasets with diverse sensor configurations demonstrate that Dynamic-LIVO improves localization accuracy and produces cleaner static colored maps in challenging dynamic environments. The source code and self-collected dataset will be publicly released upon acceptance.

0.29

GLIO2: A GPU-Parallelized Tightly-Coupled LiDAR-Inertial-GNSS System for Robust and Real-Time Global Localization and Mapping

cs.RO ·2026-10-08 ·Qi Zhang, Xikun Liu, Qijun Qin, Xiangru Wang, Junzhe Wang +3 more
similarity 0.67
Abstract · 23 pages, 16 figures, 8 tables; includes appendices

Globally consistent, real-time state estimation in large-scale, perceptually degraded environments is essential for autonomous vehicles and aerial robots, and requires fusing LiDAR, inertial, and GNSS measurements. Existing fusion methods, however, share a scan-to-map front-end with two failure modes. First, each scan is aligned to an incrementally built map that drifts under degeneracy, and once the estimate diverges the error is irrecoverable. Second, even without divergence, a registration biased by dynamic objects or wrong correspondences is propagated as a single pose constraint with an over-confident covariance, leaving its correspondences unavailable for GNSS to re-weight or relinearize. We propose GLIO2, a tightly-coupled LiDAR-Inertial-GNSS system whose GPU-parallel front-end jointly optimizes scan-to-multiscan LiDAR, IMU pre-integration, and raw GNSS measurements in a single sliding-window factor graph, sustaining real-time operation on edge hardware. A complementary offline back-end reuses the same cached factors to refine the entire trajectory in batch, completing the 30-min, 4.51-km UrbanNav Whampoa sequence in about 24 s. Across three public benchmarks (UrbanNav, MARS-LVIG, M3DGR) and self-collected UAV and vehicle data, GLIO2 attains the best overall accuracy among evaluated systems. On a 5.66-km bridge traversed at up to 96 km/h, where every competing baseline diverges under LiDAR degeneracy, it maintains 1.6 m horizontal accuracy. On an NVIDIA Jetson Orin NX, the full pipeline runs at about 25 Hz (39.60 ms per scan). The source code and datasets will be released.

0.21

DGV-DLIVO: Degeneracy-Guided Visual Fusion for Direct LiDAR-Inertial-Visual Odometry in Degenerate Tunnel Environments

cs.RO ·2026-11-17 ·Junrui Zhang
code/data similarity 0.65
Abstract

Reliable localization in long underground infrastructures remains a major challenge for autonomous inspection robots. In hydropower spillway tunnels and drainage galleries, repetitive geometric structures provide insufficient constraints along the tunnel axis, while weak texture and illumination variations further degrade visual estimation. Under this coupled degradation, existing LiDAR-inertial and visual-inertial odometry systems may lose the ability to recover continuous longitudinal motion. This paper presents DGV-DLIVO, a degeneracy-guided visual fusion for direct LiDAR-inertial-visual odometry for extreme tunnel environments. Instead of treating vision as a general complementary sensor, the proposed method exploits the LiDAR-degenerate direction as an active guidance signal to determine informative visual regions, establish LiDAR-anchored visual associations, and perform subspace-selective fusion. The visual constraints are introduced only into the deficient motion subspace, while unreliable LiDAR information in the same direction is adaptively suppressed and reliable geometric constraints are preserved. Real-world experiments in hydropower tunnels demonstrate that representative state-of-the-art LIO, LIVO, and VIO methods suffer from stagnation, oscillation, severe under-travel, curved drift, or divergence, whereas DGV-DLIVO maintains continuous and directionally consistent tunnel-axis motion estimation under both cart-mounted and handheld acquisition. It achieves a 91.4% progress ratio over the 40m tunnel sequence and significantly improves longitudinal recovery and trajectory stability. These results demonstrate the effectiveness of degeneracy-guided adaptive fusion for robotic inspection in severely degraded underground environments. The source code and a supplementary video are publicly available at https://github.com/0RayZhang0/DGV-DLIVO.

0.54

Real-Time Ground Normal Vector Estimation for Spherical Mobile 3D Mapping using LiDAR-Inertial Odometry

cs.RO ·2026-10-20 ·Tim Schubert, Fabian Arzberger, Andreas Nüchter
top venue similarity 0.65
Abstract · Proceedings of the International Symposium on Artificial Intelligence, Robotics and Automation in Space (i-SAIRAS 26)

Accurate ground plane normal estimation is essential for odometry in spherical mobile mapping systems (SMMS), which face challenges from rapid rotations and limited ground coverage. We propose two RANSAC-based approaches: single-scan estimation with normal vector scoring and multi-step validation, and LiDAR-inertial odometry (LIO)-based estimation using a global 3D map. Evaluated across diverse real-world datasets against terrestrial laser scanner ground truth, results show that LIO-based estimation significantly outperforms single-scan methods in accuracy and robustness. Integrating ground normal estimates into the motion model improves pose estimation, supporting autonomous navigation in challenging and hazardous environments.

0.25