CS Paper Radar

Resilient Decentralized Radar-LiDAR-Inertial Odometry in Challenging Subterranean Environments

Moumita Mukherjee, Avijit Banerjee, Anton Koval, George Nikolakopoulos

cs.RO ·submitted 2026-10-23 15:58 UTC · v1

Abstract

Accurate localization in GPS-denied and visually degraded environments affected by smoke, dust, or fog remains a critical challenge for autonomous systems. While LiDAR provides high-resolution spatial perception, its performance deteriorates under particulate occlusion. In contrast, frequency-modulated continuous-wave (FMCW) radar offers robustness under such conditions but suffers from sparse measurements and outliers. This article presents a resilient decentralized LiDAR Radar Inertial Odometry (LRIO) framework that fuses the complementary strengths of LiDAR, radar, and inertial sensing to achieve robust pose estimation in challenging subterranean environments. At the core of the framework is an Adaptive Residual Thresholding (ART) mechanism that autonomously detects temporal sensor degradation and selectively adjusts the fusion process to minimize unreliable measurements. Building on this, a Robust Error-Tolerant Optimal Information Filter (RETOIF) is employed within a decentralized fusion architecture to integrate LiDAR-inertial and multiple radar-inertial odometry estimates in a fault-aware manner, enhancing resilience to environmental disturbances and intermittent sensor failures. The proposed framework is evaluated using real-world sensor data collected in GPS-denied subterranean tunnels under smoke-free and smoke-degraded conditions. In the smoke-free experiment, the proposed RETOIF framework achieves a root mean square localization error (RMSE) of 2.1733, compared with 2.9929 for the conventional centralized LRIO approach, corresponding to a 27.4\% reduction in RMSE. Experimental results further demonstrate the framework's ability to maintain pose estimation under smoke-induced sensor degradation, highlighting its potential for resilient autonomous navigation and mapping in challenging subterranean environments.

Closest papers

Nearest neighbours by meaning across the whole index.

FIRE-LIVWO: Robust LiDAR-Inertial-Visual-Wheel Odometry via Failure-Immune mmWave Radar Enhancement

cs.RO ·2026-09-04 ·Kun Hu, Menggang Li, Kaidi Wu, Zhiwen Jin, Yingjie Zhao +3 more
publishedcode/data similarity 0.78
Abstract · Accepted by IROS 2026.The project website is "https://kj-falloutlast.github.io/FIRE-LIVWO"

Achieving robust SLAM in large-scale underground coal mines with complex structures and severe degeneracies remains highly challenging. Dense smoke and dust cause substantial loss of visual information and degrade LiDAR point-cloud features, while long, self-similar corridors induce geometric degeneration, leading to pronounced odometry drift. To address these issues, we propose FIRE-LIVWO: Failure-Immune mmWave Radar-Enhanced LiDAR-Inertial-Visual-Wheel Odometry, a tightly coupled multi-modal odometry framework based on an iterated error-state Kalman filter (IESKF). The framework fuses 4D mmWave radar, LiDAR, and visual features within a unified VoxelMap and jointly constructs LiDAR-radar point-to-plane residuals and sparse visual photometric residuals. In smoke-filled environments, we exploit the strong penetration of 4D mmWave radar and introduce pointwise Doppler velocity constraints to preserve state observability. In geometrically degenerate corridors, we tightly couple wheel odometry using non-holonomic constraints (NHC) and online lever-arm compensation to reduce drift. Our central contribution is a degeneration detection and adaptive fusion model switching strategy grounded in geometric and visual observability analysis, which quantifies observability online and dynamically adjusts modality weights. Real-world experiments in underground coal mines demonstrate that FIRE-LIVWO accurately identifies failure boundaries, enabling reliable modality switching under extreme conditions. Compared with baselines, it achieves superior accuracy and robustness (average localization error of 5.677m). We open source our code on Github to benefit the robotics community.

0.41

When LiDAR Fades, Radar Takes Over: LiDAR Reliability-Aware Adaptive Localization Under Airborne Obscurants

cs.RO ·2026-10-09 ·Moumita Mukherjee, Avijit Banerjee, Anton Koval, George Nikolakopoulo
similarity 0.74
Abstract

LiDAR-inertial odometry (LIO) is widely used for real-time localization and mapping, but its reliability can degrade substantially in subterranean environments affected by smoke, dust, and other airborne obscurants, whereas radar remains comparatively robust. This article presents a one-class temporal learning framework for LiDAR degradation detection and reliability-aware localization under such conditions. A broad set of degradation-sensitive cues, including spatial, cross-modal, geometric/motion, intensity, and measurement-recency features, is evaluated to characterize changes in LiDAR sensing quality. Their temporal evolution is modelled over sliding windows using an LSTM autoencoder trained exclusively on nominal operation, enabling deviations from healthy sensor behaviour to be detected without requiring labelled degradation data. The resulting LiDAR reliability estimate governs adaptive selection between LIO and radar inertial odometry (RIO), retaining LIO during reliable sensing and transferring localization authority to RIO when degradation is detected. The framework is evaluated using real-world ground robot data collected in GNSS-denied subterranean tunnels under nominal and dense-smoke conditions. Experimental results demonstrate degradation detection, adaptive modality switching, and continued localization output under severe LiDAR degradation. A feature family ablation study further shows that a reduced feature representation can improve degradation-aware localization performance in the evaluated dense-smoke scenarios, highlighting the importance of feature parsimony in one-class sensor degradation detection. The code will be released as open source to support reproducibility and further research.

0.19

FMCW-LIO: A Doppler LiDAR-Inertial Odometry

cs.RO cs.CVeess.SY ·2026-09-24 ·Mingle Zhao, Jiahao Wang, Tianxiao Gao, Chengzhong Xu, Hui Kong
top venuecode/datahighly cited similarity 0.72
Abstract · IEEE Robotics and Automation Letters (RA-L), 2024. Project Page: https://github.com/IMRL/FMCW-LIO

Conventional LiDAR-inertial odometry (LIO) or simultaneous localization and mapping (SLAM) methods heavily rely on geometric features of environments, as LiDARs primarily provide range measurements instead of motion measurements. From now on, however, the situation changes thanks to the novel Frequency Modulated Continuous Wave (FMCW) Doppler LiDARs. FMCW Doppler LiDARs not only offer the point range with high resolution but also capture the instant point Doppler velocity through the Doppler effect. In the letter, we propose FMCW-LIO, a novel and robust LIO, leveraging intrinsic Doppler measurements from FMCW Doppler LiDARs. To correctly exploit Doppler velocities, a motion compensation method is designed, and a Doppler-aided observation model is applied for on-manifold state estimation. Then, dynamic points can be effectively removed by the Doppler criteria, deriving more consistent geometric observations. FMCW-LIO eventually achieves accurate state estimation and static mapping, even in structure-degenerated environments. Extensive experiments in diverse scenes are performed and FMCW-LIO outperforms other algorithms on both accuracy and robustness.

0.78

Embedded Bare-Metal Radar-Inertial Odometry

cs.RO ·2026-10-05 ·Nicolai Adil Øyen Aatif, Morten Nissov, Kostas Alexis
code/data similarity 0.71
Abstract

Compact extraplanetary rovers and micro aerial vehicles require robust state estimation frameworks designed to operate under strict computational constraints in unforgiving environments. Typical solutions involving vision- or LiDAR-based sensing are computationally expensive and vulnerable to environments with perceptual degradation, making them poorly suited for resource-constrained platforms and austere conditions. Alternatively, Frequency Modulated Continuous Wave (FMCW) radar offers both robustness and computational efficiency by directly providing velocity measurements coupled with inherent resilience to perceptual degradation. These factors enable robust estimation, thereby reducing reliance on human operators for supervision to ensure platform safety in challenging environments. In this manuscript, we propose an embedded radar-inertial estimator tailored for low-compute platforms. All sensor drivers, data processing, and aided inertial navigation are performed on a single-core microcontroller, demonstrating its computational efficiency. Flight experiments show translational APE of $0.51-0.82\,\mathrm{m}$ and RPE of $<$3\,\% against motion capture, alongside closed-loop flight through an unmodified PX4 stack. The firmware and printed circuit board design are openly available on GitHub at https://github.com/ntnu-arl/embedded_rio and https://github.com/ntnu-arl/embedded_rio-pcb respectively.

0.32

Online Target-less Radar-LiDAR-Camera Extrinsic Calibration via Joint Optimization

cs.RO ·2026-10-03 ·Gunhee Shin, Yunsoo Kim, Chanhyuk Lee, Wanhee Kim, Minwoo Lee +5 more
published similarity 0.70
Abstract · 6 pages, 2 figures, 3 tables. Accepted to the International Conference on Control, Automation and Systems (ICCAS 2026)

Fusing radar, LiDAR, and camera enables robust perception in diverse and adverse conditions, but the fusion performance critically depends on accurate extrinsic calibration among the three sensors. In this paper, we address the problem of online target-less extrinsic calibration for the radar-LiDAR-camera system. Existing target-less methods are mostly designed for a single sensor pair, and composing the pairwise results does not guarantee consistency across the three sensors. Moreover, the sparse and noisy radar measurements make the radar-involving pairs unreliable. To tackle these challenges, we propose a joint calibration framework that constructs residuals for each sensor pair and optimizes the extrinsics of all pairs together to minimize the overall residual. Furthermore, we introduce an adaptive radar noise filter that rejects spurious radar returns using a range-dependent margin, and a correspondence accumulation strategy that aggregates sparse radar correspondences over frames. We validate our method on an in-house radar-LiDAR-camera dataset covering diverse urban environments, where it reduces calibration errors across all sensor pairs over a state-of-the-art camera-LiDAR baseline.

0.23

TRaIL-Odom: Tightly Coupled Continuous Time Radar-IMU-LiDAR Odometry with Adaptive Doppler Weighting

cs.RO ·2026-09-03 ·Chiyun Noh, Turcan Tuna, William Talbot, Marco Hutter, Laurent Kneip +1 more
top venuecode/data similarity 0.70
Abstract · Accepted for publication at the IEEE Robotics and Automation Letters on 23 August, 2026

Existing radar-LiDAR fusion methods rely on fixed residual weights, even though the informativeness of radar Doppler and LiDAR geometry is scan- and direction-dependent, leading to uniform radar weighting that misallocates Doppler information across translational directions. To address this limitation, we propose two degeneracy-aware Doppler reweighting modules within a tightly coupled Radar-IMU-LiDAR odometry framework: per-point radar reweighting and scan-wise radar gain scheduling. Since geometric degeneracy is directional, we first identify weak translational directions from the LiDAR geometry and reweight individual radar Doppler constraints based on their alignment with the weak subspace. We further adjust the overall radar contribution using LiDAR geometric anisotropy such that radar is emphasized when LiDAR observability is poor and suppressed when LiDAR constraints are already reliable. Across 13 evaluated sequences, TRaIL-Odom achieves state-of-the-art overall performance, with clear advantages in geometrically degenerate scenes. In ablation experiments on three degenerate sequences, combining the two adaptive weighting modules reduces RMSE ATE and RTE by 86.0% and 78.5% relative to the fixed-weight baseline. We make our code and an accompanying dataset publicly available at https://github.com/ChiyunNoh/TRaIL-Odom.

0.42

NM-LIO: Multiple LiDAR-Inertial Odometry Addressing LiDAR Measurement Noise Discrepancy

cs.RO ·2026-10-03 ·Gunhee Shin, Seungjae Lee, Minho Oh, Dongkyu Lee, Jaeyoung Lee +2 more
published similarity 0.69
Abstract · 10 pages, 3 figures, 1 table. Published in the International Conference on Robot Intelligence Technology and Applications (RiTA 2024)

Multiple LiDAR-inertial odometry methods have been widely applied in robotic applications owing to their enhanced accuracy and reliability. However, adopting multiple LiDAR systems can be challenging due to the discrepancies in measurement noise across different LiDARs. Existing methods have typically overlooked the noise discrepancies, which can significantly affect accuracy. In this paper, we propose Noise-aware Multiple LiDAR-Inertial Odometry (NM-LIO) that addresses the noise discrepancies. We integrate a noise model to quantify the measurement noise of each LiDAR. Additionally, we estimate the uncertainty of the residuals based on the measurement noise, allowing the measurement model to capture the noise discrepancies. Our proposed method is evaluated on a public multiple LiDAR dataset and compared with state-of-the-art methods. The experimental results demonstrate that the proposed method can accurately estimate the odometry in various environments by accounting for the noise discrepancies.

0.27

GLIO2: A GPU-Parallelized Tightly-Coupled LiDAR-Inertial-GNSS System for Robust and Real-Time Global Localization and Mapping

cs.RO ·2026-10-08 ·Qi Zhang, Xikun Liu, Qijun Qin, Xiangru Wang, Junzhe Wang +3 more
similarity 0.67
Abstract · 23 pages, 16 figures, 8 tables; includes appendices

Globally consistent, real-time state estimation in large-scale, perceptually degraded environments is essential for autonomous vehicles and aerial robots, and requires fusing LiDAR, inertial, and GNSS measurements. Existing fusion methods, however, share a scan-to-map front-end with two failure modes. First, each scan is aligned to an incrementally built map that drifts under degeneracy, and once the estimate diverges the error is irrecoverable. Second, even without divergence, a registration biased by dynamic objects or wrong correspondences is propagated as a single pose constraint with an over-confident covariance, leaving its correspondences unavailable for GNSS to re-weight or relinearize. We propose GLIO2, a tightly-coupled LiDAR-Inertial-GNSS system whose GPU-parallel front-end jointly optimizes scan-to-multiscan LiDAR, IMU pre-integration, and raw GNSS measurements in a single sliding-window factor graph, sustaining real-time operation on edge hardware. A complementary offline back-end reuses the same cached factors to refine the entire trajectory in batch, completing the 30-min, 4.51-km UrbanNav Whampoa sequence in about 24 s. Across three public benchmarks (UrbanNav, MARS-LVIG, M3DGR) and self-collected UAV and vehicle data, GLIO2 attains the best overall accuracy among evaluated systems. On a 5.66-km bridge traversed at up to 96 km/h, where every competing baseline diverges under LiDAR degeneracy, it maintains 1.6 m horizontal accuracy. On an NVIDIA Jetson Orin NX, the full pipeline runs at about 25 Hz (39.60 ms per scan). The source code and datasets will be released.

0.21