CS Paper Radar

Retrofitting centralized air compressor stations with end-use-aware predictive set-pressure control using a physics-constrained pressure-drop model

Taito Watanabe, Yohei Kono, Akira Iyozumi, Takashi Nakajima

eess.SY ·submitted 2026-10-27 05:47 UTC · v1

Abstract

Compressed air systems usually run at a constant set pressure well above the end-use requirement; the excess margin is wasted energy. A lightweight hierarchical nonlinear model predictive control (NMPC) scheme, retrofitted to the sequencing controller of a centralized compressor station typical of small and medium-sized plants, lowers the set pressure as far as the end-use requirement allows. It uses only two pressure gauges (receiver and one critical end-use point) and compressor data, without flow meters or piping surveys. The end-use pressure is predicted by a low-order pressure-drop model identified by least squares under stability, damping and steady-state equilibrium constraints, which serve use rather than accuracy: they let the measured pressure drop be held over the horizon with unit gain. Validated in three stages (plant data, a pipe-network simulator checked against measurements, and the actual controller, at most 1.41 s per update), the NMPC meets the required pressure under real demand and reduces the estimated annual energy consumption by 2.8 % relative to the current constant operation (9.3 % relative to 0.70 MPa). A PID cascade with the same gauge saves about as much only when tuned by a standard rule at its recommended setting from a constant-load step test, difficult in an operating plant; the NMPC needs no such test and keeps its performance with its initial model and default weights after plant expansion and network split. The margin becomes a design parameter instead of a fixed excess, and the controller's signals show where the supply system lacks headroom.

Comment
31 pages, 17 figures

Closest papers

Nearest neighbours by meaning across the whole index.

Model-Free Control for Residential Heating: Deployment and Simulation of Nonlinear Data-Enabled Predictive Control

eess.SY math.OC ·2026-09-18 ·Sebastian Zieglmeier, Chris Verhoek, Jaap Eising, Mathias Hudoba de Badyn
similarity 0.56
Abstract · 19 pages, 8 figures, 7 tables

Residential heating accounts for a large share of building energy use, and predictive control strategies can reduce it by anticipating rather than reacting to the room temperature alone. The usual manner of implementing predictive control, model predictive control (MPC), requires an accurate model of each individual residential unit for heating control. Obtaining this model is time-consuming to obtain manually or even impossible, and such models do not transfer across a heterogeneous building stock. Data-enabled predictive control (DeePC) removes this modeling step by designing the controller directly using measured trajectories of the system. The foundations of DeePC, however, are built on the class of deterministic linear time-invariant systems, which is an unrealistic assumption for residential heating. This work applies three recently proposed nonlinear extensions of DeePC, collectively referred to as data-driven predictive control (DPC): Select-DPC, gain-scheduling DPC, and linear parameter-varying DPC. These are compared against standard DeePC and the hysteresis controller, the industry standard in residential heating. The comparison runs over a full heating season on a calibrated digital twin of an occupied research unit, the NEST research building in Switzerland, assessed by heating energy and comfort-band violation. Moreover, gain-scheduling DPC was deployed on the real residential apartment and validated the conclusions from the simulations. Each of the DPC controllers consumes significantly less energy than the hysteresis controller, amounting to roughly $11\%$ over the season, validating the use of DPC. The nonlinear methods further outperform linear DeePC in all assessed scenarios, and we analyze the relative costs and benefits of each nonlinear method.

0.41

Time-series Foundation Models for Predictive Control: The Role of Excitation

cs.LG eess.SY ·2026-10-05 ·Mazen Amria, Jasper Hoffmann, Philipp Bordne, Anna Rothenhäusler, Lilli Frison +3 more
published similarity 0.53
Abstract · Accepted at the TS-LIMITS Workshop at NeurIPS 2026

Deploying model predictive control (MPC) requires constructing or identifying a predictive model for each target system. Time-series foundation models (TSFMs) offer an attractive option thanks to strong zero-shot forecasting capabilities across systems. However, low forecast error does not guarantee that a TSFM captures the system's response to the alternative actions considered by the controller. We study this gap using residential heat-pump control as a test bed, measuring the agreement between predicted and ground-truth effects of control interventions. Importantly, we find that TSFMs can recover the system's input-response relationship when the context contains sufficient independent control excitation. Common fine-tuning pipelines and feature smoothing reduce, but do not eliminate, the need for in-context excitation. Our results indicate that current TSFMs used for predictive control require sufficiently informative control variation in the inference context. Initial closed-loop results show promise for shorter context windows.

0.36

User-specified Kelvin-hour budgets within model predictive control for energy-efficient buildings: Simulation and field demonstration

eess.SY ·2026-09-06 ·Jicheng Shi, Colin N. Jones
similarity 0.53
Abstract

For energy-efficient building control, model predictive control (MPC) has been widely proposed to reduce energy use while maintaining prescribed indoor temperature bounds. In practice, MPC implementations may still produce temperature-bound violations because of model mismatch, weather-forecast errors, and softened constraints introduced to preserve feasibility. Existing soft- constrained MPC usually handles this trade-off through slack-weight tuning, so users cannot prescribe a violation-severity budget before operation. This paper develops a Kelvin-hour (Kh)-budget MPC that allows users to specify a running-average budget for temperature-bound violation severity. During operation, the controller uses the realized Kh budget surplus or overspend to update the temperature bounds, providing step-by-step budget feedback. We evaluate the method in two high-fidelity BOPTEST simulation cases and in an occupied residential deployment. In the first one-zone case, prescribed budgets produce clear running-average Kh violation responses across predictors and disturbance settings. At a prescribed budget of 0.005 Kh/step, the controller reduces energy use by 31.9% and Kh violation by 36.2% relative to the built-in default controller. In the second coupled two-zone case, separate zone budgets produce zone-level responses, with 18.9%-20.5% energy reduction and 9.4%-64.3% zone-level Kh violation reduction. In the occupied residential deployment, the running-average Kh violations remain close to or below their prescribed budgets under real sensing, actuation, weather, and occupancy conditions.

0.27

An end-to-end differentiable transient vapor-compression framework for automated machine sizing and unified optimal control

eess.SY cs.CEphysics.app-ph ·2026-08-20 ·Sam Yang
code/data similarity 0.52
Abstract · the paper is not novel enough; need further investigation

Accelerating the electrification of thermal energy requires vapor-compression heat pumps capable of dynamic, grid-responsive operation. However, equipment engineering remains fragmented across static rating-point selection, stiff multi-phase transient simulation, and gradient-based optimal control. Here, we present an end-to-end differentiable, finite-volume vapor-compression framework implemented natively in JAX that automates machine sizing directly from stated thermal duties and unifies dynamic simulation with predictive control under a single compiled residual $\dot{y}={f}(t,{y},{u})$. Thermodynamic evaluations bypass runtime root-finding via bilinear $(p,h)$ manifolds pre-flashed from Helmholtz equations of state, enabling analytical forward-mode automatic differentiation. Mass conservation across multi-phase coils is strictly preserved by incorporating both $(\partialρ/\partial p)_h$ and $(\partialρ/\partial h)_p$ partial derivatives into the dynamic pressure differential equation. The sizer directly inverts compressor displacement, electronic expansion valve area, and heat-exchanger tube counts via four-point cycle synthesis and $\varepsilon$-NTU matching using the identical polytropic compressor map. Crucially, the compiled physics kernel is shared symmetrically between $L$-stable TR-BDF2 stiff integration and implicit-Euler Model Predictive Control (MPC), eliminating plant-controller surrogate mismatch. Validated against open-access experimental benchmarks without parameter fitting, the framework predicts cooling capacity with $7.37\%$ MAPE across 16 mini-split operational runs and bounds on-period cooling error within $1.19\%$--$1.62\%$ on utility-scale Hardware-in-the-Loop traces. This work provides an open-source, differentiable foundation for automated machine synthesis, dynamic grid orchestration, and gradient-based hardware-control co-design.

0.36

Model Predictive Control of Wind Turbines: A Model-Oriented Review of Prediction Models, Control Objectives, and Nonlinear Aerodynamic Formulations

eess.SY math.DSmath.OC ·2026-10-22 ·Roya Khalili-Amirabadi, Mohsen Jalaeian-Farimani, Mahdi Ghane
published similarity 0.52
Abstract · Khalili-Amirabadi, R., Jalaeian-Farimani, M., & Ghane, M. (2026). Model Predictive Control of Wind Turbines: A Model-Oriented Review of Pred…

Model predictive control (MPC) has been applied to wind-turbine regulation with markedly different internal prediction models, ranging from linearized low-order turbine models to nonlinear, aeroelastic, floating, and data-driven predictors. This review organizes the literature primarily by the model propagated by the controller and treats model order, predictor representation, MPC formulation, control objective, and validation plant as separate descriptors. Primary studies show that low-order linear or piecewise-affine predictors are attractive for constrained power and speed regulation, whereas flexible drivetrain, structural, and floating models are needed when drivetrain twist, tower motion, blade loads, or platform dynamics are explicit control quantities. Nonlinear and economic MPC studies further demonstrate coordinated pitch/torque control across broad operating regions, while preview, repetitive, and data-driven formulations address wind prediction, periodic loads, and model mismatch. Particular attention is given to aerodynamic pitch dependence: variable-pitch turbine dynamics can be non-affine with respect to applied pitch, and the term NMPC alone does not prove that the original nonlinear pitch map is retained inside the optimizer. The review therefore adopts a conservative, equation-based classification for direct nonlinear applied-pitch propagation. Here, direct nonlinear applied-pitch propagation means that the applied pitch at each prediction step is evaluated inside the original nonlinear aerodynamic map, rather than replacing that dependence by a linearized, scheduled, piecewise-affine, or learned surrogate. The literature supports a remaining integration challenge at the intersection of flexible drivetrain prediction, nonlinear aerodynamic pitch treatment, explicit constraints and load objectives, and validated adaptive or learned model correction.

0.35

Mitigating Forced Oscillations in Power Systems via Data-Enabled Predictive Control

eess.SY ·2026-08-27 ·Soraya Daabak, Verena Häberle, Gabriela Hug, Gustavo Valverde
similarity 0.51
Abstract

Sustained forced oscillations in power systems, driven by large cyclic loads such as data centers, pose a challenge to conventional power system stabilizers (PSSs), which rely on fixed tuned parameters and limited adaptability. This paper investigates the use of Data-Enabled Predictive Control (DeePC) as a data-driven alternative for damping such oscillations. DeePC constructs control actions directly from measured trajectories without requiring an explicit system model, enabling adaptation to changing operating conditions. We evaluate the performance of DeePC on a multi-machine two-area system subject to forced oscillations and compare it against a conventional PSS. The study examines the impact of different input-output configurations and the role of representative historical data in the Hankel matrix construction. Results show that DeePC can achieve superior damping. However, its effectiveness depends critically on the quality and representativeness of the underlying dataset. These findings highlight the potential of data-driven predictive control to complement or outperform conventional stabilizers in modern power systems with evolving and uncertain dynamics.

0.24

Headroom-Aware Stochastic Adaptive Model Predictive Control for Load Frequency Control in Microgrids

eess.SY ·2026-09-04 ·Erfan Mehdipour Abadi, Shuo Yuan, Le Yi Wang, Caisheng Wang, Feng Lin
similarity 0.49
Abstract

As the penetration of inverter-based resources (IBRs) increases in microgrids, they are increasingly expected to play a greater role in load frequency control (LFC). Model predictive control (MPC) is attractive for LFC because it incorporates system dynamics and operational constraints. However, most MPC-based LFC formulations rely on fixed reserve headroom based on forecasted renewable availability or storage systems. Under short-term renewable intermittency, IBR headroom is stochastic and time-varying, causing optimal control commands to exceed the physically deliverable regulation capability and cause stochastic saturation. This control-actuator mismatch degrades LFC performance. Accordingly, this study develops two headroom-aware strategies for PV-dominated microgrids. First, stochastic headroom constrained MPC (SHCMPC) incorporates headroom predictions through time-varying input constraints to enforce control feasibility. Second, stochastic adaptive MPC (SAMPC) embeds headroom awareness into the MPC objective function by adaptively penalizing control actions based on predicted headroom, reducing reliance on units with limited headroom without hard time-varying constraints. Simulation results show that stochastic saturation degrades conventional MPC-based LFC, particularly under tight reserve margins. Both strategies improve regulation performance. SHCMPC eliminates saturation events, while SAMPC achieves substantial saturation mitigation with lower computational effort, offering a computationally efficient alternative for real-time LFC under stochastic renewable availability.

0.22

Economic Model Predictive Control with Policy-Guided Terminal Ingredients

eess.SY ·2026-09-02 ·Salim Msaad, Robert D. McAllister
similarity 0.49
Abstract

Conventional designs for model predictive control typically rely on terminal costs and constraints derived from a steady state to guarantee closed-loop stability and performance. However, this dependence on a steady-state assumption limits the applicability of this control method to systems in which such a fixed operating point is either not available or not desirable. This work introduces a novel framework, termed policy-guided MPC, to address this limitation. Our approach constructs terminal costs and constraints using a known sub-optimal control policy. Specifically, the terminal region is defined around a center determined by a rollout of the policy, and a penalty on deviation from this center is used to define the terminal cost. This method obviates the need for a steady state or reference trajectory. Closed-loop performance guarantees are established relative to the guiding policy, for both finite and infinite horizon problems. The effectiveness of the proposed framework is demonstrated through numerical simulations on an energy management example.

0.22