CS Paper Radar

A Wearable Sensor Array on Conductive Textiles for Body Surface Temperature Mapping

Amiri Onuki, Akihito Noda

eess.SP ·submitted 2026-10-27 10:51 UTC · v1
published

Abstract

Continuous monitoring of body-surface temperature distributions can provide useful information for wearable health and thermal-condition monitoring. However, practical daily-use wearable systems for distributed temperature sensing remain difficult to implement because multiple sensor nodes require power delivery and data collection across a garment. Conventional wiring increases system complexity, reduces placement flexibility, and can compromise the wearability of garment-integrated sensor arrays. To address this issue, we present a conductive-textile-based wearable temperature sensing system in which the textile itself serves as a shared bus for both DC power delivery and data communication. Each sensor node is implemented as a compact, battery-free circular board with a diameter of 21 mm and a weight of 0.9 g, integrating a commercial temperature sensor and custom circuitry for UART/DC superposition. The shared textile bus enables flexible node placement without individual wiring while supplying power to each node. Address-based half-duplex UART with master polling enables collision-free multi-node communication. To demonstrate the system-level capability, we implemented an 18-node sensor array on a garment worn by a mannequin and developed a real-time temperature mapping viewer. In a thermal scanning demonstration using warm air from a heat gun with a set temperature of approximately 50 °C, the 18-node array captured spatiotemporal temperature variations over the garment surface at a refresh rate of 99.2 Hz. These results show that the proposed conductive-textile bus can support real-time, high-refresh-rate distributed temperature mapping, providing a practical basis for garment-integrated body-surface monitoring and future multi-sensor wearable systems.

Comment
6 pages, 6 figures. Accepted manuscript of a paper published in Proceedings of the SICE Festival 2026 with Annual Conference, September 14-17, 2026, Yokohama, Japan. (c) 2026 The Society of Instrument and Control Engineers (SICE)
Journal ref
2026 SICE Festival with Annual Conference (SICE FES), Yokohama, Japan, 2026, pp. 586-591
DOI
10.23919/SICEFES71276.2026.11739166

Closest papers

Nearest neighbours by meaning across the whole index.

Protocol-Flexible Custom NFC for Wire-Free Wearable Sensor Networks

cs.NI ·2026-09-20 ·Riku Maeda, Akihito Noda
publishedunusual similarity 0.62
Abstract · 4 pages, 5 figures, 1 table. Accepted manuscript; accepted for publication in IEEE Sensors Letters

This study presents a custom near-field communication (NFC) system with software-defined protocol implementation for wearable sensors distributed across the body. Conventional wired implementations can degrade wearability because of mechanical constraints, whereas radio-based wireless approaches such as Bluetooth are affected by body-induced signal attenuation and limited communication coverage. The proposed system is compatible with previously demonstrated fabric-integrated meander coils, which provides a feasible path toward garment-scale NFC communication areas. The system combines a microcontroller unit with compact modulation and demodulation circuits, allowing medium access control and other communication protocols to be implemented in software. Experimental results demonstrate continuous acquisition of three-axis acceleration data from three sensor tags, achieving a per-tag polling rate of $222\,\mathrm{Hz}$ and an effective throughput of approximately $16\,\mathrm{kbps}$, delivering $156$ valid samples per second per tag at a measured packet error rate of $30\%$.

0.64

Toward Motion Capture Textiles: A Batteryless IMU Array Powered and Networked Through a Conductive-Fabric Bus

eess.SP cs.NI ·2026-10-14 ·Ryusei Miyakawa, Akihito Noda
published similarity 0.62
Abstract · 4 pages, 4 figures, 1 table. Accepted for publication in IEEE Sensors Letters

Motion capture is increasingly important in healthcare, rehabilitation, and sports applications. However, conventional vision-based systems require camera infrastructure and line-of-sight conditions, limiting their use in daily environments. This paper proposes a location-independent platform for motion capture, based on an array of IMU (inertial measurement unit) sensor nodes without individual wiring or onboard batteries, enabled by two-dimensional communication and power delivery over conductive fabric. Pipeline processing in each sensor node, combined with a token-passing protocol, enables collision-free and stable data acquisition at 50 Hz. Real-time three-dimensional reconstruction of flexible objects is further demonstrated by applying Hermite spline interpolation to orientation data from grid-aligned IMUs. Against a cylinder of known radius, the reconstructed surface deviates by 2.60 mm RMS over the 225 mm span of the array. The reconstruction is formulated for the quasi-static regime, and this letter empirically validates it in that regime. The hardware platform and communication protocol implemented in this work enable further investigation toward dynamic motion capture textiles.

0.35

Cyber-Secure Wearable, Ultra-Low-Power Networked Sensors for Soldier Health Monitoring: Insights from the CAPSARII project

cs.ET cs.AIcs.ARcs.CR+2 ·2026-11-15 ·Luciano Bozzi, Christian Celidonio, Umberto Nuzzi, Massimo Biagini, Stefano Cherubin +17 more
publishedbenchmark similarity 0.54
Abstract · Pre-print version

The CAPSARII project advances a cyber-secure, ultra-low-power wearable platform and Internet of Battlefield Things (IoBT) framework to support real-time monitoring of military personnel and data-driven decision support. The architecture integrates smart-textile sensing, a body/squad area mesh, edge-deployed AI on secure RISC-V microcontrollers, and cloud/federated analytics for cross-mission learning and comparative studies. Two representative use cases--pilot fatigue and warfighters operating in harsh environments--guide requirements, validation, and interface design (including HUD and haptic feedback). As an initial step toward embedded models, we benchmark stress classification on a public wearable dataset: tree-ensemble baselines achieve state-of-the-art performance for accuracy and F1 (e.g., XGBoost: $\mathrm{Accuracy}=0.901\!\pm\!0.023$, $\mathrm{F1}=0.920\!\pm\!0.019$), while a feature-based Transformer attains the highest AUC ($0.963\!\pm\!0.025$), informing feature-engineering and compression choices for edge deployment. Building on these results, CAPSARII employs HW/SW co-design, model compression (pruning, quantization, distillation), and precision tuning to meet stringent energy and memory budgets; it further investigates Processing-in-Memory accelerators for future efficiency gains. A structured gap analysis highlights the remaining challenges: establishing validation standards for physiological signal quality and textile durability; achieving low-latency, scalable BAN/SAN communications under mobility and interference; and deploying hybrid lightweight/post-quantum cryptography with robust device identity and side-channel resilience on constrained endpoints. By consolidating these elements into a coherent, secure IoBT stack, CAPSARII delineates a practical roadmap from laboratory baselines to mission-ready soldier monitoring in both training and operational scenarios.

0.34

Location-Based Safety Management with Wearable Seamless Indoor-Outdoor Positioning

cs.RO ·2026-10-15 ·Anh-Van Vu, Seungwoo Chae, Changmin Sung, Van-Tuan Nguyen, Dongsoo Han
published similarity 0.53
Abstract · 6 pages

Reliable worker localization is essential for real-time industrial safety management, but seamless outdoor-indoor positioning remains challenging. GNSS performs well outdoors yet degrades near buildings and fails indoors, while many indoor systems require costly infrastructure or extensive calibration. This paper presents a practical safety-oriented positioning system that uses resource-constrained wearable tags and a device-cloud split architecture for continuous outdoor-indoor worker tracking. The tag integrates GNSS, IMU, barometric sensing, LTE Cat-M communication, and performs lightweight sensor fusion, while the cloud server executes map-aware fusion for continuous tracking. Developed as an operational platform, the system also includes a database, a map tool, and a dashboard that provide real-time monitoring, geofencing-based access alerts, and safety and productivity analysis. Experiments with multiple participants, each walking an approximately 1400 m outdoor-indoor route, using LTE Cat-M communication, achieve mean errors of 1.32 m indoors and 3.30 m outdoors, while maintaining low positioning latency and efficient power consumption. These results demonstrate the feasibility of wearable-based seamless positioning for scalable real-time safety management.

0.40

IMUdrape: Generating Garment-Mounted Virtual IMU Data from Text through Physics-Based Cloth Simulation

cs.CV cs.HC ·2026-11-02 ·Zikang Leng, Thomas Plötz
code/data similarity 0.51
Abstract · 34 pages, 7 figures, 15 tables. Under review. Project page: https://zikangleng.github.io/imudrape/

Inertial sensors are moving into clothing, from sensorized sportswear to garments instrumented with hundreds of IMUs. Sewn into clothing, a sensor no longer moves rigidly with the body: loose fabric slides, twists and swings, so a garment-mounted sensor records the motion of the fabric as well as that of the body, and this extra motion differs from one garment to the next. Models for such sensors need training data recorded with the deployed garment, yet labeled data are scarce. Virtual IMU data generated from videos or text have eased this scarcity for body-attached sensors, but existing generators attach their virtual sensors rigidly to the body. We present IMUdrape, which generates garment-mounted virtual IMU data from text through physics-based cloth simulation. IMUdrape synthesizes motion from activity descriptions, reconstructs the target garment as a sewing pattern from photographs, places virtual IMUs at the deployment's real sensor positions, and simulates the garment with an intersection-free contact solver, so that every simulation yields paired garment and body signals. On four real datasets with clothing-mounted sensors, IMUdrape improves on existing virtual-data approaches for both activity recognition and full-body pose estimation. With one real subject, its data improve recognition macro-F1 by 7% to 46% over real data alone and by 2% to 11% over body-mounted virtual data from the same motion. When the garment is simulated on recorded motion, the pose error without any real training data falls by 30% to 33% relative to generated motion, and garment data remain 12% more accurate than body data. IMUdrape thus reduces the amount of real data that garment-mounted sensing requires.

0.42

An Energy Efficient Wearable for Monitoring Elderly People Health

eess.SP cs.CY ·2026-08-26 ·M. Much, A Moraes Filho, J. Sieg, F. Hessel, A. Cataldo Neto +1 more
similarity 0.51
Abstract · 8 pages, 11 figures

The aged population is exposed to risk situations, like falls, sudden changes in vital signs, and faints. These situations become common at this life stage due to a decrease in body capacity and illnesses increase. This scenario imposes attention on families and the national health system. Some studies propose to overcome this problem through elderly health monitoring systems based on smartphones, smartwatches, and other equipment that usually cover low-efficient communication systems and low battery life. This paper proposes an efficient health monitoring system based on Sigfox IoT service and a watch-type wearable device for sensing elderly motion, location, and vital signs to predict risk situations designed to achieve at least 30-days of battery life. Our experimental results show that this architecture is a low-cost, low-power, efficient, and feasible elderly health monitoring solution.

0.36

Mobility Enhancement of Patients Body Monitoring based on WBAN with Multipath Routing

cs.NI ·2026-10-02 ·Yasna Ghanbari Birgani, Nastooh Taheri Javan, Mohsen Tourani
publishedunusualhighly cited similarity 0.50
Abstract

One of the promising applications of wireless sensor networks (WSNs) is monitoring of the human body for health concerns. For this purpose, a large number of small sensors are implanted in the human body. These sensors altogether provide a network of wireless sensors (WBANs) and monitor the vital signs and signals of the human body; these sensors will then send this information to the doctor. The most important application of the WBAN is the implementation of the monitoring network for patient safety in the hospital environment. In this case, supporting patients' mobility is one of the basic needs, which has been underestimated in recent studies. The problem that involves providing the required energy for the units used in this type of network is challenging; for this reason, sent/received units with very low power consumption and with a very small radius are used in order to save energy. The resulting small sending range leads to the lack of support for patients' mobility. In this paper, the ad hoc mode is suggested for use to establish a network and a multipath routing algorithm for the purpose of supporting patients' mobility in a hospital setting. The results of the simulation show that, in addition to supporting patients' mobility, the use of the proposed idea instead of previously presented protocols reduces delays in data transmission and energy consumption; it also increases the delivery rate depending on the destination and the lifetime of the network, while increasing routing overhead.

0.62

TherMosaic: Accelerating Perceived Thermal Transitions Through Spatiotemporal Thermal Feedback

cs.HC ·2026-09-04 ·Zining Zhang, Jiasheng Li, Myungin Lee, Zeyu Yan, Jin Ryong Kim +1 more
top venue similarity 0.49
Abstract

Thermal feedback can enrich immersive interaction, but thermoelectric devices often change temperature too slowly to match interactive timing. We present TherMosaic, a spatiotemporal thermal feedback approach that accelerates perceived temperature transitions by leveraging two perceptual mechanisms: spatial summation and thermal adaptation. Focusing on the fingertip, we first investigate this approach using a custom 2*2 array of independently controlled Peltier modules. Across three controlled perceptual studies, we show that distributed thermal stimulation can preserve stable hot and cold percepts despite local deviations, that adaptation helps maintain these percepts during changing stimulation, and that combining these effects reduces perceived transition time by about 30%-40% for transitions originating from hot or cold states. We then translate the same design principles into a standalone wearable implementation of TherMosaic and evaluate it in virtual reality. Our results show that this approach reduces perceived thermal lag and improves temporal alignment between thermal and visual events in interactive use.

0.44