CS Paper Radar

Toward Motion Capture Textiles: A Batteryless IMU Array Powered and Networked Through a Conductive-Fabric Bus

Ryusei Miyakawa, Akihito Noda

eess.SP cs.NI ·submitted 2026-10-14 10:53 UTC · v1
published

Abstract

Motion capture is increasingly important in healthcare, rehabilitation, and sports applications. However, conventional vision-based systems require camera infrastructure and line-of-sight conditions, limiting their use in daily environments. This paper proposes a location-independent platform for motion capture, based on an array of IMU (inertial measurement unit) sensor nodes without individual wiring or onboard batteries, enabled by two-dimensional communication and power delivery over conductive fabric. Pipeline processing in each sensor node, combined with a token-passing protocol, enables collision-free and stable data acquisition at 50 Hz. Real-time three-dimensional reconstruction of flexible objects is further demonstrated by applying Hermite spline interpolation to orientation data from grid-aligned IMUs. Against a cylinder of known radius, the reconstructed surface deviates by 2.60 mm RMS over the 225 mm span of the array. The reconstruction is formulated for the quasi-static regime, and this letter empirically validates it in that regime. The hardware platform and communication protocol implemented in this work enable further investigation toward dynamic motion capture textiles.

Comment
4 pages, 4 figures, 1 table. Accepted for publication in IEEE Sensors Letters
Journal ref
IEEE Sensors Letters, vol. 10, no. 11, Art. no. 7005504, Nov. 2026
DOI
10.1109/LSENS.2026.3744423

Closest papers

Nearest neighbours by meaning across the whole index.

A Wearable Sensor Array on Conductive Textiles for Body Surface Temperature Mapping

eess.SP ·2026-10-27 ·Amiri Onuki, Akihito Noda
published similarity 0.62
Abstract · 6 pages, 6 figures. Accepted manuscript of a paper published in Proceedings of the SICE Festival 2026 with Annual Conference, September 14-1…

Continuous monitoring of body-surface temperature distributions can provide useful information for wearable health and thermal-condition monitoring. However, practical daily-use wearable systems for distributed temperature sensing remain difficult to implement because multiple sensor nodes require power delivery and data collection across a garment. Conventional wiring increases system complexity, reduces placement flexibility, and can compromise the wearability of garment-integrated sensor arrays. To address this issue, we present a conductive-textile-based wearable temperature sensing system in which the textile itself serves as a shared bus for both DC power delivery and data communication. Each sensor node is implemented as a compact, battery-free circular board with a diameter of 21 mm and a weight of 0.9 g, integrating a commercial temperature sensor and custom circuitry for UART/DC superposition. The shared textile bus enables flexible node placement without individual wiring while supplying power to each node. Address-based half-duplex UART with master polling enables collision-free multi-node communication. To demonstrate the system-level capability, we implemented an 18-node sensor array on a garment worn by a mannequin and developed a real-time temperature mapping viewer. In a thermal scanning demonstration using warm air from a heat gun with a set temperature of approximately 50 °C, the 18-node array captured spatiotemporal temperature variations over the garment surface at a refresh rate of 99.2 Hz. These results show that the proposed conductive-textile bus can support real-time, high-refresh-rate distributed temperature mapping, providing a practical basis for garment-integrated body-surface monitoring and future multi-sensor wearable systems.

0.41

IMUdrape: Generating Garment-Mounted Virtual IMU Data from Text through Physics-Based Cloth Simulation

cs.CV cs.HC ·2026-11-02 ·Zikang Leng, Thomas Plötz
code/data similarity 0.61
Abstract · 34 pages, 7 figures, 15 tables. Under review. Project page: https://zikangleng.github.io/imudrape/

Inertial sensors are moving into clothing, from sensorized sportswear to garments instrumented with hundreds of IMUs. Sewn into clothing, a sensor no longer moves rigidly with the body: loose fabric slides, twists and swings, so a garment-mounted sensor records the motion of the fabric as well as that of the body, and this extra motion differs from one garment to the next. Models for such sensors need training data recorded with the deployed garment, yet labeled data are scarce. Virtual IMU data generated from videos or text have eased this scarcity for body-attached sensors, but existing generators attach their virtual sensors rigidly to the body. We present IMUdrape, which generates garment-mounted virtual IMU data from text through physics-based cloth simulation. IMUdrape synthesizes motion from activity descriptions, reconstructs the target garment as a sewing pattern from photographs, places virtual IMUs at the deployment's real sensor positions, and simulates the garment with an intersection-free contact solver, so that every simulation yields paired garment and body signals. On four real datasets with clothing-mounted sensors, IMUdrape improves on existing virtual-data approaches for both activity recognition and full-body pose estimation. With one real subject, its data improve recognition macro-F1 by 7% to 46% over real data alone and by 2% to 11% over body-mounted virtual data from the same motion. When the garment is simulated on recorded motion, the pose error without any real training data falls by 30% to 33% relative to generated motion, and garment data remain 12% more accurate than body data. IMUdrape thus reduces the amount of real data that garment-mounted sensing requires.

0.42

Calibration-free IMU-based Relative Orientation Estimation under Dynamic Human Motion

cs.RO eess.SY ·2026-10-22 ·Ruiyuan Li, Hassan Osman, Ajay Seth, Manon Kok
similarity 0.57
Abstract · 8 pages, 7 figures, 1 table. Submitted to IEEE Sensors Journal

Recent magnetometer-free inertial measurement unit (IMU) methods can reduce drift in joint motion estimation using rigid-body constraints, but they typically require pre-calibrated sensor locations, assumptions of specific joint models (e.g., hinge joints) or limited motion types, or an external reference for global orientation. Furthermore, challenges related to high-frequency impacts (e.g. at foot strikes during gait) and numerical differentiation of noisy measurements have not been explicitly addressed. We propose an extended Kalman filter that estimates relative IMU orientation and sensor location simultaneously, requiring neither offline sensor location calibration nor a global orientation anchor. A systematic simulation study shows that the quality of the relative orientation and the sensor location estimates depends on different motion-intensity sources: the joint center acceleration and the relative angular velocity, respectively. A low-pass filter (LPF) is used to mitigate real-signal outliers before applying the rigid-body constraint. When applied to the OpenSense dataset with real IMU measurements across four subjects with three lower-body joint types during walking and complex tasks including various motion types, the proposed method achieves an overall relative orientation error of 2.61°, compared with 10.40° for a baseline using offline-estimated sensor locations and 7.43° for a baseline using marker-derived sensor locations. These results show that the proposed calibration-free estimation framework handles real IMU data effectively and achieves accurate relative orientation without offline sensor location calibration.

0.16

Multi-Sensor Edge Angle Detection for Performance Analysis in Ski Jumping

eess.SP eess.SY ·2026-08-18 ·Ivan Simeonov, Lukas Schulthess, Hanna Mueller, Marc Nölke, Michele Magno +2 more
published similarity 0.55
Abstract

In ski jumping, performance during the gliding phase depends on achieving an aerodynamic posture that maximizes the lift-to-drag ratio. In the V-style technique, the ski edge angle is a key determinant. Reducing the edge angle flattens the skis, increases their effective surface area, and improves aerodynamic lift, ultimately contributing to longer flight distances. Ski edge angles are biomechanically constrained by the limited range of ankle inversion. Current sensing solutions widely quantify these angles using multi-system approaches that combine sensor signals through geometric relations. Such configurations require instrumentation on both the boot and the ski, altering mass distribution, affecting balance during flight, and increasing system complexity. To overcome these limitations, this work presents a wearable sensing system that measures both boot inclination and ski edge angle without modifying the ski surface. Two ultrasonic Time of Flight (ToF) sensors and an in-shoe Inertial Measurement Unit (IMU) are integrated into a single boot-mounted unit. Edge angles are estimated by combining ultrasonic distance measurements with IMU data through geometric reconstruction of the boot-ski configuration. Laboratory experiments demonstrate an angle resolution of 0.4500°, a Mean Absolute Error (MAE) of 0.2640°, and a coefficient of determination exceeding 99\% when compared with reference measurements, indicating strong linear agreement between the two modalities. The system achieves an end-to-end latency of 30.31 ms, enabling real-time feedback suitable for athlete training, while consuming 1.28 mW of power. With a total weight of only 18.6 g the proposed system enables unobtrusive measurement of ski edge angle and boot orientation.

0.35

A Black-Box Positioning Solution for Effortless Integration in Wearable Navigation

cs.RO cs.AR ·2026-10-15 ·Anh-Van Vu, Changmin Sung, Dongsoo Han
published similarity 0.55
Abstract · 8 pages

Accurate localization is critical for a wide range of applications, including navigation, augmented reality, safety management, and healthcare. However, achieving accurate positioning remains challenging, especially in GPS-degraded environments. Pedestrian Dead Reckoning (PDR), which estimates position based on inertial sensor data, offers a promising alternative but typically demands substantial effort in algorithm design and system integration. This complexity often leads to prolonged development timelines and elevated costs. To address these challenges, we present the PDR Sensor (PDRS), a plug-and-play, black-box PDR module optimized for seamless integration into wearable and IoT platforms. PDRS integrates a microprocessor and an inertial measurement unit (IMU) within a compact, low-power module. It executes real-time sensor fusion onboard, providing position updates via standard interfaces (I2C, SPI, UART). Experimental evaluations demonstrate its high robustness, achieving a step detection error of just 0.16% over 1250 steps and a traveled distance error of 1.87% under diverse conditions. The system further exhibits low latency (2.5 ms) and modest power consumption (52.35 mA). Unlike conventional studies, the PDRS leverages a holistic co-design of hardware and software to enhance performance and integration aspects, simplifying adoption without requiring deep expertise. By lowering technical barriers, PDRS enables developers and researchers to prioritize innovation in IoT and wearable technologies, accelerating prototyping, reducing development time, and advancing industry progress. Future work aims to enhance accuracy, reduce power usage and module size, and integrate AI-driven techniques to better mitigate drift.

0.65

Protocol-Flexible Custom NFC for Wire-Free Wearable Sensor Networks

cs.NI ·2026-09-20 ·Riku Maeda, Akihito Noda
publishedunusual similarity 0.54
Abstract · 4 pages, 5 figures, 1 table. Accepted manuscript; accepted for publication in IEEE Sensors Letters

This study presents a custom near-field communication (NFC) system with software-defined protocol implementation for wearable sensors distributed across the body. Conventional wired implementations can degrade wearability because of mechanical constraints, whereas radio-based wireless approaches such as Bluetooth are affected by body-induced signal attenuation and limited communication coverage. The proposed system is compatible with previously demonstrated fabric-integrated meander coils, which provides a feasible path toward garment-scale NFC communication areas. The system combines a microcontroller unit with compact modulation and demodulation circuits, allowing medium access control and other communication protocols to be implemented in software. Experimental results demonstrate continuous acquisition of three-axis acceleration data from three sensor tags, achieving a per-tag polling rate of $222\,\mathrm{Hz}$ and an effective throughput of approximately $16\,\mathrm{kbps}$, delivering $156$ valid samples per second per tag at a measured packet error rate of $30\%$.

0.64

Location-Based Safety Management with Wearable Seamless Indoor-Outdoor Positioning

cs.RO ·2026-10-15 ·Anh-Van Vu, Seungwoo Chae, Changmin Sung, Van-Tuan Nguyen, Dongsoo Han
published similarity 0.54
Abstract · 6 pages

Reliable worker localization is essential for real-time industrial safety management, but seamless outdoor-indoor positioning remains challenging. GNSS performs well outdoors yet degrades near buildings and fails indoors, while many indoor systems require costly infrastructure or extensive calibration. This paper presents a practical safety-oriented positioning system that uses resource-constrained wearable tags and a device-cloud split architecture for continuous outdoor-indoor worker tracking. The tag integrates GNSS, IMU, barometric sensing, LTE Cat-M communication, and performs lightweight sensor fusion, while the cloud server executes map-aware fusion for continuous tracking. Developed as an operational platform, the system also includes a database, a map tool, and a dashboard that provide real-time monitoring, geofencing-based access alerts, and safety and productivity analysis. Experiments with multiple participants, each walking an approximately 1400 m outdoor-indoor route, using LTE Cat-M communication, achieve mean errors of 1.32 m indoors and 3.30 m outdoors, while maintaining low positioning latency and efficient power consumption. These results demonstrate the feasibility of wearable-based seamless positioning for scalable real-time safety management.

0.40

X-Hinges: 3D Printing Self-Sensing Compliant Mechanisms for Continuous and Multi-DOF Motion Sensing

cs.HC ·2026-09-10 ·Xiang Chang, Haiyang Yan, Stefanie Mueller, Jiaji Li
top venue similarity 0.53
Abstract · Accepted at ACM UIST 2026. 15 pages, 24 figures. Author's accepted manuscript

We present X-Hinges, a design and fabrication method for self-sensing compliant mechanisms based on multi-material FDM 3D printing. By co-printing two conductive filaments of different conductivities within a compliant body, we embed resistive sensing elements directly during fabrication without post-assembly, enabling continuous motion sensing across multiple degrees of freedom in a single print. The structure supports three degrees of freedom, each equipped with a dedicated sensing element configuration for multi-DOF motion estimation. We develop a precision data acquisition system and data-driven regression models that enable continuous, real-time motion sensing. We also introduce an interactive design tool for customizing the geometry, mechanical properties, degrees of freedom, and sensing configurations of X-Hinges. The tool also supports augmenting existing 3D models with self-sensing structures, endowing ordinary objects with continuous multi-DOF sensing capabilities. Finally, we present a set of application examples demonstrating the capability of X-Hinges for fabricating personalized interactive interfaces.

0.47