CS Paper Radar

Tags Helping Tags: Coordination-Free Power Boosting for Battery-less Backscatter Networks

Mathew Salas, Xin Xiong, Sihua Shao, Atef Elsherbeni, Mostafa Hassanalian, Rafael Fierro

eess.SY eess.SP ·submitted 2026-11-05 23:55 UTC · v1

Abstract

Battery-less backscatter sensor nodes powered by radio-frequency wireless power transfer are attractive for large or hard-to-reach deployments, but their range is typically limited by the forward power-transfer link rather than by communication sensitivity. We present a method for improving power delivery, and thus range, in dense tag deployments by having nearby tags act as helpers: each helper terminates its antenna in purely reactive impedances, reflecting the power beacon's signal toward a target tag so that it combines constructively with the direct line-of-sight path and increases the power the target harvests. On a hardware testbed, helpers using discrete impedance control are shown to increase the target tag's harvested power by over 50% above an all-absorbing baseline, while randomly set helper impedances give no reliable benefit, and are sometimes even detrimental. We further propose and implement a local algorithm that lets each helper tune its own impedance using only measurements of the target's packet rate, without channel estimation or coordination between helpers, and we show that it brings the target's packet rate close to that of an independently tuned configuration. These results suggest that independent, passive sensor nodes can cooperatively extend each other's power-transfer range with minimal added infrastructure.

Closest papers

Nearest neighbours by meaning across the whole index.

WiFi Backscatter for Green Internet of Things: Concepts, Research Trends, and Practical Challenges

cs.NI ·2026-09-28 ·Weiqi Wu, Shuo Wang, Zhaoyuan Xu
survey similarity 0.62
Abstract

WiFi backscatter has emerged as a promising technology for green Internet of Things (IoT) connectivity by enabling battery-free devices to communicate through widely available WiFi signals. Despite substantial progress in recent years, a considerable gap remains between research prototypes and practical deployment. This paper provides an overview of WiFi backscatter from the perspective of practical and green IoT systems. We first introduce the fundamentals and key enabling techniques, together with potential IoT applications. We then outline recent research trends toward higher throughput, concurrent communication, simplified deployment, commercial compatibility, and joint communication and sensing. Furthermore, we identify the key challenges that still hinder practical deployment, such as limited transmitter-to-tag operating range and packet loss in frequency-shifted backscatter. We believe that addressing these challenges will be critical to enabling WiFi backscatter to become a practical communication technology for future green IoT systems.

0.15

Harvesting-Aware Routing for Low-Latency Reliable Transmission in Interference-Powered Networks

cs.NI ·2026-10-09 ·Azadeh Sheikholeslami, Allan Nguyen
similarity 0.59
Abstract

We consider a multi-hop wireless network where energy-harvesting nodes rely solely on ambient radio-frequency interference as their power source. The goal is to deliver a packet from source to destination with minimum latency while guaranteeing a target end-to-end outage probability under Rayleigh fading. This gives rise to a joint routing and power allocation problem in which interference plays a dual role: it provides harvestable energy, but also impairs link reliability. We first transform the intricate, multiplicative end-to-end outage constraint into an additive form. Then, we propose two optimal algorithms. The first, HOPE, minimizes the bottleneck harvesting latency, i.e., the longest energy-accumulation time along the path, by reducing the problem to a least-cost path computation on a graph with interference-aware link weights. The second, THOPE, extends the objective to total end-to-end latency, adding the cumulative transmission delay, and likewise admits a closed-form least-cost path solution. Both algorithms are solved in polynomial time via Dijkstra's algorithm and yield explicit expressions for the optimal transmit powers. Extensive simulations reveal that HOPE and THOPE reduce the average total latency by up to an order of magnitude compared with shortest-path and minimum-energy benchmarks, while exhibiting sharply concentrated delay distributions that are largely insensitive to interferer density.

0.23

Mobile Backscatter Communication for the Battery-less Internet of Things

cs.NI ·2026-09-01 ·Weining Song, Thiemo Voigt, Stefanos Kaxiras, Yuan Yao, Luca Mottola
published similarity 0.59
Abstract · 11 pages, 20 figures. Extended version of the paper accepted at MSWiM 2026

We enable backscatter communication in the battery-less mobile Internet of Things (IoT). Backscatter communication is extensively studied in static settings. Existing designs are, however, fundamentally mismatched with mobility and time-varying energy patterns. Channel conditions rapidly fluctuate, impacting the achievable data rates and thus transmission costs. Energy availability varies unpredictably, possibly forcing devices to remain quiescent to recharge energy buffers. The two issues compound each other: while recharging, a battery-less mobile IoT device may miss more favorable channel conditions. We design a lightweight decision system that dynamically determines when to transmit by checking short-term trends in signal strength, while using Non-volatile Memory (NVM) to retain packets in unfavorable channel conditions and across energy failures. Using a prototype we built and real-world mobility and power traces, we compare our design against a rate-adaptive baseline that only considers the instantaneous channel conditions. Experimental results show that our system improves throughput by up to 5.16x while reducing transmission energy consumption by up to 47.3%, with only 0.23% - 7.3% additional energy overhead.

0.40

Beyond Feasibility: Efficient and Robust On-Device Localization with UWB Concurrent Transmissions

eess.SP cs.NIeess.SY ·2026-11-06 ·Enrico Soprana, Michael Stocker, Davide Vecchia, Matteo Trobinger, Carlo Alberto Boano +1 more
similarity 0.58
Abstract · Submitted to the IEEE Transactions on Mobile Computing

Concurrent transmissions (CTX) enable an ultra-wideband (UWB) tag to range to, or self-localize from, multiple nodes with a single frame reception, significantly improving update rate and energy efficiency compared to traditional approaches. Prior work demonstrated the concept feasibility via prototypes whose real-world applicability is however hindered by many limitations, notably including their inability to directly execute on UWB tags and to cope with interfering UWB signals. We address these limitations in two ways. First, we redesign the core CTX techniques to enable a fast and efficient execution on resource-constrained MCUs without sacrificing accuracy. Second, we leverage the new features in the IEEE 802.15.4z standard to achieve robustness to interference from other UWB devices and enable tags to dynamically select which anchors to use, two crucial and unexplored capabilities in CTX-based systems. We quantitatively evaluate our approach experimentally in two real-world testbeds with different characteristics. We first analyze our new techniques individually, offering an in-depth discussion of design choices and performance trade-offs. Then, we embed all our techniques into a CTX-based system enabling a tag to self-localize entirely on-device, unlocking gains up to 44% in runtime and 85% in energy efficiency compared to traditional approaches.

0.37

LoopHIL: Looping Hardware into LLM-assisted Agents for Wireless Embedded Systems

cs.NI cs.AIcs.ARcs.SE ·2026-10-16 ·Dhairya Shah, Spanddhana Sara, Savitha Viswanadh Kandala, Ambuj Varshney
similarity 0.57
Abstract · 8 pages, 8 figures, 4 tables. Under review

LLM agents are widely used for software development and debugging, but their adoption in embedded systems, especially for wireless tasks, remains limited. This is because embedded development requires hardware-in-the-loop testing. Agents cannot directly observe the spectrum, probe pins, or measure power, so they cannot verify wireless link functionality; currently, human engineers perform this verification. We systematically evaluate whether LLM agents can establish wireless links when provided with hardware access. We introduce LoopHIL, a framework that lets agents control a multi-device RF bench, monitor it with a spectrum analyzer, logic analyzer, and energy meter, and validate links against a verification ladder, all within code-enforced safety limits. Across four increasingly complex tasks, from generating a carrier to backscatter decoding by a commercial receiver, and using six models from two vendors, hardware-in-the-loop increases task completion rates from 54% to 79% and from 17% to 83% on the most challenging task. It also halves task time and output tokens. With debugging tools, agents decrease tag power consumption by up to 96%. However, small models often report unverified claims, so independent hardware checks remain necessary.

0.56

Towards Energy-Neutral IoT Sensors: Low-Cost Chirp-Based Backscattering Node Using a COTS Microcontroller and Multi-Load Front-End

eess.SP ·2026-09-23 ·Tijl Schepens, Liesbet Van der Perre, Gilles Callebaut
similarity 0.56
Abstract

Backscatter communication has proven to be a key enabler for energy-neutral sensor nodes in the IoT. It allows ultra-low-power nodes to transmit sensor data by reflecting incident RF signals. Practical large-scale deployment requires hardware solutions that are both cost-efficient and widely available. This paper investigates the practical limits of implementing backscatter transmitters exclusively using COTS components. We compare a two-load and multi-load architecture in terms of hardware requirements, complexity and spectral efficiency highlighting the most important trade-offs. A multi-load backscatter architecture is developed using a resource constrained low-power microcontroller, levering DMA to achieve high switching speeds while minimizing processing overhead. Furthermore, we present a layout agnostic load design methodology based on scattering parameters, allowing precise control of the reflection coefficients. A prototype implementation demonstrates a successful backscatter transmission of a single-sideband chirp with reduced harmonic distortion. Measurement results show suppression of the backscattered carrier and the second sideband by 10 dBm. This demonstrates that low-cost sensor nodes can be built using COTS components enabling remote monitoring at extended lifetimes.

0.23

Secure Polarization-Shift Backscatter Identification Applied to Battery-Free BLE Sensors Powered by Wireless Power Transfer

cs.NI ·2026-09-24 ·Taki Eddine Djidjekh, Quentin Bernyer, Alexandru Takacs
published similarity 0.56
Abstract

This paper presents a lightweight and protocolindependent security mechanism for battery-free Bluetooth Low Energy (BLE) sensor nodes operating in Simultaneous Wireless Information and Power Transfer (SWIPT) architecture. The proposed approach exploits polarization-shift backscattering of the wireless power wave to transmit an encrypted device identification prior to data communication. A fail-safe RF switch and orthogonally polarized antennas are integrated as an external add-on module, enabling controlled backscatter without modifying the original energy-harvesting rectifier. The identification payload is encrypted using AES-128 and transmitted with minimal energy overhead. Experimental validation on a battery-free BLE sensor node demonstrates reliable extraction of the backscattered identification signal, seamless coexistence with BLE advertising, and improved RF-to-DC harvesting efficiency compared to rectifier-based backscatter solutions. The results confirm that polarization-shift backscatter identification provides an effective and practical security for battery-free BLE sensing systems.

0.26

Joint Target-Tag Estimation in Ambient Backscatter-Based ISAC

eess.SP ·2026-10-04 ·Awadhesh Gupta, Kumar Vijay Mishra, Naveen K. D. Venkategowda, Aditya K. Jagannatham
top venuetheory similarity 0.56
Abstract

Integrated sensing and communication (ISAC) has emerged as a key paradigm for unifying radar sensing and wireless communications within a shared hardware and spectral framework. In parallel, ambient backscatter communication (AmBC) has gained attention as a low-power solution for enabling passive connectivity by modulating and reflecting existing radio-frequency signals. Motivated by these developments, this paper investigates an integrated sensing and ambient backscatter communication (ISABC) framework in which a dual-functional radar-communication (DFRC) transceiver jointly performs high-resolution target sensing and low-power tag detection in cluttered environments. Within this ISAC and AmBC setting, we develop a comprehensive system model that jointly captures the estimation of target and clutter parameters, including delay, Doppler shift, and complex reflectivity, together with the recovery of embedded AmBC tag symbols. The resulting DFRC signal model reveals strong coupling among direct-path reflections, clutter echoes, and passive backscatter signals, leading to a highly entangled estimation problem. To address this challenge, we propose a robust three-stage signal processing framework that sequentially estimates target and clutter parameters before detecting the AmBC tag message. This structured approach effectively disentangles the superimposed components, improving both sensing accuracy and communication reliability in ISAC systems. Extensive simulations, benchmarked against the Cramer-Rao lower bound (CRLB), demonstrate the superior estimation performance of the proposed DFRC-based solution. The results further highlight the fundamental trade-offs between sensing accuracy and backscatter communication efficiency in ISABC systems.

0.42