CS Paper Radar

Cable construction effects on the lateral forces and wakes of helically stranded cables under oblique inflow

Tielin Ma, Junlin Zhang, Jingcheng Fu, Chongwen Jiang, Chuan Ye

cs.CE physics.flu-dyncs.RO ·submitted 2026-11-08 10:13 UTC · v1

Abstract

Helically stranded cables in aerial towing systems experience oblique inflow, but are often modeled as smooth cylinders, neglecting three-dimensional cross-stream coupling and surface texture. We perform large-eddy simulations and spectral proper orthogonal decomposition for a smooth cylinder and four stranded cables at four inclinations from $22.5^\circ$ to $90^\circ$, all stationary, with $Re \approx 1.0 \times 10^4$. Aerodynamic differences are governed mainly by cross-sectional symmetry and strand-scale groove depth. Force-source decomposition shows that surface pressure contributes 94.9%--98.3% of the mean normal force and dominates the mean lateral force. High-symmetry, quasi-circular envelopes maintain balanced circumferential pressure, whereas deep-grooved, low-symmetry tri-lobed geometries produce asymmetric separation and a persistent lateral pressure imbalance. In the wake, high-symmetry cables sustain spanwise-synchronized Karman shedding at moderate-to-high inclinations, concentrating fluctuation energy in a dominant low-rank mode. Deep grooves disrupt shedding coherence, deflect the recirculation zone laterally, and spread energy across broadband scales. Mean lateral force and lateral-force fluctuations are therefore decoupled: the quasi-circular $(1 \times 19)$ cable has minimal mean lateral force but strong periodic fluctuations, while the deep-grooved $(3 \times 7)$ cable has weak fluctuations but appreciable mean lateral force. These results support construction-dependent cable selection and aerodynamic load modeling.

Closest papers

Nearest neighbours by meaning across the whole index.

Passive Stiffness Shaping in Cable-Suspended Aerial Manipulation via Movable Compliant Anchors

cs.RO cs.MAeess.SY ·2026-09-30 ·Antonio Franchi, Amr Afifi
similarity 0.52
Abstract

Cable-suspended aerial manipulation offers a lightweight architecture for cooperative transportation and physical interaction, yet the passive mechanical response perceived at the load remains insufficiently understood and systematically exploited. This work interprets aerial vehicles as movable compliant anchors and develops a gravity-aware quasi-static theory for predicting and shaping the passive Cartesian stiffness of a suspended load. The formulation applies to an arbitrary number of aerial vehicles connected to a point load by taut, straight, inextensible cables. At a selected gravity-loaded equilibrium, aerial-anchor compliance and transverse cable geometric compliance combine in series within each leg, while the leg stiffnesses act in parallel on the load. For isotropic aerial-anchor behavior, each leg is exactly equivalent to a virtual unilateral elastic cable, revealing an axial--transverse stiffness decomposition governed by the equilibrium tension. These results define a nonlinear map from commanded-anchor configuration to passive load stiffness, whose differential enables local constraint-preserving shaping through anchor repositioning. A dynamic rigid-body validation framework with nonlinear vehicle control, elastic-damped tendons, and environmental contact is defined to assess when and to what extent the derived stiffness remains predictive beyond the assumptions of the analytical model.

0.14

Aerial Non-Stop Trajectories Preserving the Equilibrium of Loads Suspended by Variable-Length Cables

eess.SY ·2026-09-11 ·Antonio Franchi, Alberto Landi, Chiara Gabellieri
similarity 0.50
Abstract

This work studies equilibrium-preserving non-stop trajectories of aerial carriers connected to rigid loads by variable-length cables. Internal-force motions vary the cable directions without changing the load wrench, while cable-length actuation shapes the radial realization of the carrier trajectories. We derive an explicit cable-length law for realizing prescribed carrier-position profiles along a fixed direction, with constant altitude as a relevant specialization. Under this constraint, a carrier stops exactly when its cable direction stops changing. This characterization reveals a distinction between unrestricted and level motion: variable cable lengths enable bounded non-stop motion with two carriers, whereas periodic level non-stop motion is obstructed for two carriers and constructively achieved for three or more under explicit geometric and feasibility conditions. Numerical simulations illustrate the constant-altitude construction.

0.25

Dynamics Modeling of a Multi-UAV Slung Load System Using a Discrete-Link Cable Approach

cs.RO ·2026-10-05 ·Harvey Merton, Ian W. Hunter
top venuecode/data similarity 0.47
Abstract · Presented at ICRA 2026 as an accepted paper

A common assumption to simplify the problem of controlling a multi-UAV slung load system (MUSLS) is that the flexible cables can be modeled as massless rigid rods. In this work, we propose an alternative Euler-Newton derived dynamical model which uses a series of rigid links to model the flexible cables. The model is specifically designed to allow efficient simulation using Featherstone's articulated body algorithm. We perform real-world validation of this model on gentle, aggressive, and tension-engagement maneuvers and run a parameter sweep to determine the number of links, joint damping, and joint friction to achieve the greatest model fidelity. The model closely matches real-world flight data with mean load translation errors below 132 mm (5.5% of the cable length) and orientation errors below 11.4 degrees. We make the real-world flight data publicly available for the development of future cable models.

0.54

Cosserat Modeling of Trimmed Helicoid Soft Arms with a Separated-Section Constitutive Law

cs.RO ·2026-09-21 ·Zhihang Qin, Linxin Hou, Zeyu Zhong, Yuchen Sun, Wenci Xin +8 more
similarity 0.45
Abstract

Cosserat rod models for soft robots usually construct sectional stiffness by summing material properties over a common cross-section. This assumption becomes inaccurate for trimmed helicoid arms, where load-bearing helix domains are separated and connected only through sparse fused crossings. This paper formulates a separated-section constitutive law that evaluates each helix domain in its local frame and pulls its constitutive response back to the backbone, yielding an effective backbone stiffness. Sparse-fusion mechanics captures the additional compliance caused by relative motion between neighboring domains and determines channel-wise reduction profiles $η_c(s/L)$ for bending, torsion, and extension. The resulting effective sectional stiffness is strongly anisotropic: bending and extension are reduced by about one order of magnitude, whereas torsion remains close to the effective backbone stiffness. The resulting sectional law is embedded in a geometrically exact dynamic Cosserat model with GVS discretization and routed-tendon actuation. Across 103 measured configurations, the three datasets give pooled normalized position errors of $7.7 \ \%$, $6.7 \ \%$, and $7.8 \ \%$, while each full-arm solve requires approximately $0.3 \ \mathrm{s}$ on one CPU core (Intel Xeon, Cascade Lake, $2.8 \mathrm{GHz}$), enabling rapid model-based planning, state and load estimation, and morphology--control co-design for architected soft robots.

0.38

Topology optimization of force densities for form finding of cable structures

cs.CE math.OC ·2026-08-25 ·Nicolò Pollini
similarity 0.43
Abstract

This paper presents a topology optimization approach for the form finding of cable networks based on the force density method. The proposed framework combines the force density method with topology optimization based on continuous density variables to identify the equilibrated geometry and effective connectivity of cable structures simultaneously. Design variables are assigned to the cable network members and control their force densities through a SIMP interpolation, complemented by an explicit binary promoting term in the objective function. As a result, cable members vanish or remain active throughout the optimization process. The equilibrium configuration is obtained by enforcing the force density method equations, while the objective drives the optimized network as close as possible to a prescribed reference form. Volume constraints, passive boundary regions, and a minimum connectivity requirement at loaded joints are incorporated to yield physically meaningful and numerically stable designs. Several numerical examples based on cable net ground structures defined by horizontal, vertical, and diagonal members are used to study the proposed approach. A dedicated rounding study shows that the relaxed density variables converge to nearly discrete values at the end of the optimization process, with only a minor correction required after thresholding. A study of the volume fraction constraint further shows that reducing the permitted structural volume can trigger a qualitative transition in the optimized topology, from a redundant, densely braced configuration to a minimal load path. Finally, an assessment of solver performance shows that the proposed formulation scales reasonably well with problem size.

0.28

SHAFT: A Slack-Compensating, Helical-Buckling-Attenuating Flexible-Shaft Transmission for Lightweight Multi-DoF Manipulation

cs.RO ·2026-09-19 ·Tomoya Takahashi, Moses Gladson Selvamuthu, Richiro Tadakuma, Kazutoshi Tanaka
published similarity 0.42
Abstract · 9 pages, 14 figures, submitted as proceedings of IROS2026

Lightweight and slim manipulators enable safe operation in human living environments. Proximal actuation using remote transmission mechanisms, such as wire-driven or Bowden cables, effectively reduces inertia and arm size by relocating motors near the base and transmitting torque to distal joints. Existing approaches either increase mass through additional components, such as pulleys for direction changes, or suffer from reduced transmission efficiency due to friction losses. Flexible shaft transmission avoids both mass increase and excessive friction losses, but faces increasing angular transmission error due to helical buckling caused by slack generated at joint bending. To address this problem, we propose SHAFT: a Slack-compensating, Helical-buckling-Attenuating Flexible- shaft Transmission mechanism. This mechanism compensates for slack through a proximal tensioner, improving the angular transmission error and efficiency of flexible shaft transmission without increasing the moving mass of the arm section. In a transmission path containing four 90-degree bends, the proposed mechanism demonstrated approximately 30% higher efficiency and approximately 65% lower angular transmission error compared to a flexible shaft transmission without a tensioner. Using this mechanism, we fabricated a 6-Degree-of-Freedom (DoF) arm with a 1-DoF gripper manipulator consisting of a rotary module housing motors with a tensioner, and a 280 g weight for the arm module. The proposed manipulator represents a novel remote actuation system for achieving lightweight construction with high efficiency, contributing to the acceleration of safe robot deployment in human environments.

0.42

MuJoCable: Reduced-Order Surface-Routed Cable Transmission for Tendon-Driven Robots

cs.RO cs.CE ·2026-09-09 ·Yi Zhang, Qi Shao, Yicong Lin, Muyuan Ma, Tao Sun +1 more
similarity 0.42
Abstract · 14 pages, 6 figures, 3 tables

Tendon transmissions reduce distal inertia and add compliance, yet routing, slack, and friction govern motion and force transfer. Mainstream rigid-body robotics simulators such as MuJoCo do not jointly resolve moving noncircular contact, unilateral tension, and segment friction. We present MuJoCable, which adds a reduced-order, configuration-dependent cable transmission to MuJoCo. Its routing algorithm jointly optimizes an ordered path across moving analytic and mesh surfaces. A unilateral axial law, directional Capstan propagation, and nodal virtual work map this path to segment tensions and body forces. The warm-started engine plugin applies these forces during simulation and exposes route and load states for design. Pulley benchmarks recover analytical transmission relations with a Capstan-ratio error below 0.5%. On the underactuated 18-joint SpiRobs, MuJoCable reveals friction-driven load growth and proximal redistribution of joint rotation that the native tendon does not represent. Hardware tests on SpiRobs and a tendon-route-coupled finger reproduce observed motion sequences. By making physical threading executable, MuJoCable brings transmission sources of the simulation-to-reality gap into route, cable, and actuator design before fabrication.

0.26

AFD-CAMLs: Agile Force-Distribution-Aware Planning and Control for Cable-Suspended Aerial Multi-Lifting Systems

cs.RO ·2026-10-01 ·Antreas Kourris, Sihao Sun
similarity 0.42
Abstract · 9 pages, 11 figures

Multiple UAVs can cooperatively transport heavy payloads while controlling their position and orientation. Trajectory-based methods offer high agility while satisfying system constraints, but can produce uneven force distributions when the tension-to-wrench allocation is redundant or ill-conditioned, particularly under geometric mismatch and low-level tracking errors. We propose a hybrid planning-and-control framework to address this problem. A global planner generates payload trajectories and cable-force references by exploring the allocation null space under a prescribed internal-force setting. These references augment the cost of a centralized local planner, promoting feasible force distributions while generating trajectories for all UAVs. An admittance filter then compares the planned forces with onboard cable-tension estimates and adjusts the kinematic references to improve force tracking in degenerate or near-degenerate configurations. Simulations and experiments involving four to ten UAVs demonstrate more balanced tension distributions during both hovering and demanding agile maneuvers, without compromising agility or payload-tracking performance.

0.27