CS Paper Radar

Robust State-Parameter Estimation in Second-Order Thévenin Batteries

Wissam Khennoune, G. Q. Bao Tran, Thach Ngoc Dinh, Jérémy Van Gorp, Mathieu Moze

eess.SY math.OC ·submitted 2026-11-09 20:26 UTC · v1

Abstract

We propose a scheme for estimating the full states and parameters of a second-order Thévenin battery model, using distinct features of the measured current. An identification step, run during suitable rest intervals, identifies the resistances and capacitances of the two RC branches from the voltage relaxation by linear least squares, without knowledge of the open-circuit voltage (OCV) map. An online estimator then runs continuously: the polarization voltages are estimated by open-loop observers; the series resistance is updated at current jumps using least squares; the state of charge (SOC) is propagated by Coulomb counting using the current capacity estimate, and both estimates are updated periodically by a sliding-window regression. We show that the identification is exact under a mild rank condition, that the series resistance is recovered at the first current jump, and that the online state and capacity estimates converge exponentially under verifiable excitation conditions. We also establish robustness of the online estimator under bounded process disturbances and measurement noise.

Comment
Under review for European Control Conference (ECC)

Closest papers

Nearest neighbours by meaning across the whole index.

Estimating the Health and State of Charge of Each Cell in a Second-Life Battery System from Field Data

eess.SY ·2026-09-03 ·Martin Cornejo, Julian Meyer-Schwickerath, Juan Victor Sandalinas, Andreas Jossen
benchmark similarity 0.64
Abstract · 35 pages, 9 figures, includes supplementary material (10 pages, 9 supplementary figures, 2 supplementary notes). Code and data: https://doi.…

Effective use of battery storage depends on reliable estimation of its state of health (SOH) and state of charge (SOC). Model-based state estimation requires the open-circuit voltage (OCV) curve, which is typically unknown for second-life batteries. We present a framework that jointly estimates the states and parameters of an equivalent circuit model solely from field operation data, using Gaussian process regression to reconstruct the OCV curve. Applied to a real second-life battery system of 27 modules and 324 cells, it reveals SOH heterogeneity, a systematic SOC imbalance, and two faulty cells, all validated against a reference measurement. We aggregate the cell SOH and SOC to module level and benchmark them against a lumped-module model fitted without the individual cell voltages. The lumped-module model follows the average behavior and cannot capture the limiting cells, overestimating SOH by up to 31% and SOC by up to 23%.

0.27

Relative Discharge Stage (RDS) Classification: A Practical Indicator of Battery Discharge Progress

cs.LG ·2026-09-23 ·Khoa Tran, Tri Le, Hung-Cuong Trinh, Hung Tran-Nam
similarity 0.61
Abstract

Accurate remaining discharge time (RDT) prediction is challenging in real-world battery applications because future load profiles are unknown and highly dynamic. To address the uncertainty of continuous RDT regression, this paper introduces Relative Discharge Stage (RDS), a battery-management indicator that represents the remaining discharge condition using five interpretable classes: Normal, Good, Moderate, Low, and Recharge Required. Unlike state of charge (SOC), which reflects the current charge level, RDS characterizes the remaining discharge process without requiring future-current information during inference. A physics-informed RDS classification framework is proposed, combining SOC estimation with lightweight temporal learning. The SOC-estimation component includes second-order ECM state and terminal-voltage prediction, hysteresis and OCV temperature correction, core-temperature estimation, and AEKF state correction, supported by OCV evaluation, online STC-ECM parameter adaptation, and pretrained neural residual-voltage correction. The measured current, terminal voltage, surface temperature, and estimated SOC are arranged into a sliding observation window and processed by a lightweight temporal convolutional network. Experiments on two public lithium-ion battery datasets demonstrate robust RDS classification, with accuracy exceeding 80% under varying load and thermal conditions.

0.04

System Identification for Nonlinear Stochastic State-Space Models Using Ensemble Kalman Inversion with Application to Lithium-Ion Batteries

eess.SY ·2026-10-19 ·Farzaneh Barat, Rachel Carter, Sara Wilson, Huijeong Kim, Xinfan Lin +1 more
similarity 0.58
Abstract · 16 pages, 8 figures, 3 tables

Nonlinear state-space system identification has attracted decades of interest, yet remains challenging because of the interplay among unknown parameters, nonlinear dynamics, and latent state variables. Its difficulty increases dramatically when the state and parameter dimensions increase. To address this challenge, we develop an ensemble Kalman inversion (EnKI)-based approach. This approach leverages EnKI to perform maximum a posteriori parameter estimation through successive local Gaussian approximations, enabling an iterative and incremental search for unknown parameters. The search combines Monte Carlo sampling with Kalman-type updates to evolve an ensemble of parameter samples, thereby offering empirical stability and the ability to handle strongly nonlinear models. The EnKI search is coupled with state estimation conditioned on the latest parameter estimates. This enables parameter identification along with latent state recovery. To improve scalability for large datasets, we further develop a cascaded EnKI (CasEnKI) method, which assimilates subdatasets sequentially to accelerate computation. We validate the proposed methods using a lithium-ion battery model with ten state variables and 18 unknown parameters. Simulation results show that the EnKI approach offers high identification accuracy and empirical stability in parameter search. Further, experimental results illustrate the computational efficiency and scalability of the CasEnKI method for large battery datasets.

0.12

When voltage sensors fail: Electrochemically constrained fault-tolerant state estimation for flat-plateau LFP batteries

eess.SY eess.SP ·2026-10-05 ·Feng Guo, Luis D. Couto, Hamid Hamed, Khiem Trad, Dong Zhang +3 more
published similarity 0.57
Abstract · Published in Energy Storage Materials, Volume 91 (2026), Article 105553. This is the authors' accepted manuscript. Please cite the Version o…

The flat voltage plateau of lithium iron phosphate (LFP)/graphite cells makes electrochemical-state errors and voltage-measurement abnormalities produce similar innovations, complicating state-of-charge (SOC) estimation. This work proposes an electrochemically constrained residual-bias compensation dual extended Kalman filter (RBC-DEKF) with uncertain-initialization commissioning. A thermal control-oriented parameter-grouped single-particle model (CPG-SPMT) provides paired-electrode dynamics and terminal-voltage prediction, while a separately configurable voltage-discrepancy state accommodates systematic residuals. When the initial SOC is uncertain, residual adaptation is suspended over a verified-healthy startup window. Buffered data support electrochemically constrained trajectory matching, followed by calibrated state replay and residual-channel reactivation. Frozen cross-cycle healthy-residual calibration supports commissioning and remains in the voltage prediction after handover. Evaluation covers 216 additive-bias and 168 multiplicative-gain profiles over 24 A123 temperature-drive-cycle trajectories. Relative to Single-EKF, the original RBC-DEKF reduces mean SOC RMSE from 7.646 to 0.170 percentage points for additive bias and from 22.646 to 0.356 percentage points for gain faults. Separately, 18 nonzero-initial-error profiles on three representative 50%-SOC-anchored segments give a full-record mean SOC RMSE of 1.747 percentage points, including startup, for the commissioned realization, versus 11.192 and 11.400 for the always-on RBC-DEKF and conventional joint EKF. Representative delayed bias, 10-s ramp, and gain tests show that the corrected SOC trajectory remains stable after fault introduction. The central contribution is electrochemically constrained temporal coordination of uncertain-state recovery and subsequent voltage-discrepancy accommodation.

0.66

Recursive Parameter Identification of Nonlinear Stochastic State-Space Models via Sequentialized Ensemble Kalman Inversion

eess.SY ·2026-09-19 ·Farzaneh Barat, Rachel Carter, Sara Wilson, Huazhen Fang
publishedbenchmark similarity 0.56
Abstract · Accepted for publication in the 2026 65th IEEE Conference on Decision and Control (CDC)

Recursive parameter identification in nonlinear stochastic state-space models is challenging because unknown parameters affect the measurements through latent-state dynamics. This paper develops a sequentialized ensemble Kalman inversion method for recursive parameter identification from streaming measurements. The proposed method represents the parameter posterior by an evolving ensemble and updates it sequentially as new measurements become available. For each parameter ensemble member, implicit particle filtering is used to approximate the predictive observation statistics required for parameter correction. This formulation enables recursive parameter learning. The method is evaluated on a strongly nonlinear benchmark, with comparison to several existing methods, and then on a nonlinear double-capacitor lithium-ion battery model. The numerical results demonstrate accurate recursive parameter identification and latent-state estimation.

0.30

Regularised Iterative Generalised Least Squares with Optimal Selection of the Hyper-Parameter for Identifying Nonlinear Phenomenological Models

cs.LG stat.MEeess.SY ·2026-08-19 ·Mark Cary, Charles Bokor
similarity 0.54
Abstract · 18 pages, 5 figures, 2 tables

In some fields currently dominated by empirical approaches, such as state of health (SoH) prediction for lithium-ion batteries, phenomenological models motivated by quasi-physical thinking contain parameters to be estimated from experimental data. Often the structure of such models yields fully or partially confounded parameters, which are difficult or even impossible to estimate reliably. To preserve the desired model formulation and simultaneously improve the numerical conditioning for the problem we introduce a ridge regression scheme. An automated method is provided, based on information theoretic measures of model performance, which optimises the ridge regression hyper-parameter at each iteration. The formulae presented require fixed point iteration to solve for the hyper-parameter. Given a suitable starting value, analysis demonstrates convergence is very rapid. The optimal hyper-parameter selection mechanism is incorporated within an efficient regularised iterative generalised least squares mechanism, capable of fitting both heteroscedastic and serially correlated data as required. Simulation confirms the efficacy of the overall method.

0.35

A Hybrid State Space-Attention Architecture for Forecasting the Trajectories of Battery Degradation

cs.AI physics.chem-ph ·2026-11-14 ·Shrey Patel, Bhargav Srinivas Rao, Samet Ayhan
benchmark similarity 0.54
Abstract

Early-life battery degradation trajectory forecasting aims to predict a battery cell's full state-of-health (SOH) trajectory from its initial charge-discharge cycles, potentially reducing cell qualification and evaluation time from months to days. Despite recent advances, accurate forecasting remains challenging for emerging battery chemistries, data-scarce domains, and cells exhibiting degradation behaviors beyond those observed during training. Existing state-of-the-art approaches increasingly rely on model scaling, large language model-derived aging-condition embeddings, and extensive fold-specific hyperparameter tuning, raising concerns about computational efficiency, reproducibility, and generalization. This work introduces DecayFormer, a compact hybrid state-space and attention architecture designed for early-life degradation trajectory forecasting. DecayFormer combines cycle-level selective recurrence, using a single scalar state per channel, with an attention mechanism queried by the recurrent state. It further incorporates state-of-charge (SOC) interval statistics and a master curve head that jointly estimates a scalar lifetime and a monotonically non-increasing SOH profile parameterized by normalized lifetime. We evaluate DecayFormer on the BatteryLife benchmark using all 22 aging-condition-exclusive folds, with a single run per fold and one fixed configuration across all folds, without fold-specific tuning. DecayFormer achieves mean test MAPE values of 2.25% on Li-ion, 2.76% on CALB, 0.95% on Na-ion, and 7.19% on Zn-ion. These results demonstrate the potential of compact sequence models to deliver accurate early-life degradation forecasts across diverse battery chemistries and aging conditions, without relying on extensive model scaling or per-fold optimization.

0.08

Koopman Spectral Reduced-Order Modeling of Spherical Diffusion in Lithium-Ion Batteries

eess.SY ·2026-09-09 ·Jihoon Moon
similarity 0.54
Abstract

Physics-based battery models provide internal electrochemical states for estimation and control, but solving the partial differential equations governing solid diffusion can be computationally expensive. This paper therefore develops an analytical Koopman spectral reduced-order model for the single particle model. The Koopman eigenfunctionals and eigenvalues are derived directly from the eigenfunctions of the self-adjoint zero-flux diffusion operator. The zero mode represents the volume average concentration, the nonzero modes describe decaying radial gradients, and projection of the current dependent surface flux yields a linear state-space model that reconstructs the average, surface, and full radial concentrations. Unlike data-driven Koopman models, the proposed formulation requires neither training data nor empirical lifting functions. Compared with a 400 control volume finite volume model (FVM) during a constant 1C discharge, the 80 Koopman mode model achieves negative and positive surface concentration RMSE values of $1.26\times10^{-5}\,\mathrm{mol/m^{3}}$ and $4.10\times10^{-6}\,\mathrm{mol/m^{3}}$, a terminal voltage RMSE of $8.42\times10^{-4}\,\mathrm{V}$. The models with 5 and 80 Koopman modes were approximately 225 and 31 times faster than the FVM model, respectively. These results demonstrate a physically interpretable and computationally efficient representation of battery diffusion dynamics.

0.30