CS Paper Radar

Improved Closed-Form Identification of the Air-Gap Permeance in Magnetic Equivalent Circuits of Rotor-Eccentric Electric Motors

Philip Desenfans

eess.SY ·submitted 2026-11-13 06:54 UTC · v1
unusual

Abstract

Fast and accurate simulation of electric motors is essential for their design, fault diagnosis and control. Magnetic equivalent circuits (MECs) offer a computationally efficient alternative to the finite element method (FEM), yet their flux tube representation poorly captures the air-gap field. This creates a challenge, as the air gap stores most of the magnetic energy and governs the electromagnetic torque and, in rotor-eccentric motors, the unbalanced magnetic pull (UMP). Existing air-gap permeance expressions vary widely in their results for torque ripple and UMP and account for tooth-normal eccentricity only. This paper proposes the dual-term air-gap permeance (DTAP) model, a closed-form expression for the air-gap permeance between a stator and a rotor tooth that accounts for tooth-normal and tooth-tangential eccentricity, with and without rotor skew. Its parameters are identified from a FEM model of the air gap and the complete set of tooth heads, which includes the shielding by the neighbouring teeth. For three motors, DTAP reproduces the FEM air-gap permeance with a 2.8-4.8 times smaller error than the state of the art, at a comparable computational cost. Implemented in the MEC of an eccentric induction motor, it reproduces the torque ripple within 1.6% and the peak UMP within 1.3% of the reference, i.e., with 2.8 and 27 times smaller deviations than the state of the art. DTAP thereby enables MEC to predict the torque pulsations and bearing loads of eccentric motors more accurately without sacrificing computational speed.

Comment
This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may no longer be accessible

Closest papers

Nearest neighbours by meaning across the whole index.

Electric-Field Induction Motor with Discrete Circuit Elements and Improved Rotor Dynamics

cs.RO eess.SYphysics.app-phphysics.ins-det ·2026-10-27 ·Alex S. Miller, Jeffrey H. Lang
unusual similarity 0.46
Abstract

Electric-field-based actuators and machines lead the design space at the nanoscale and in biological systems, while having the potential to be used in favorable macroscale applications which prioritize minimal mass, performance in a vacuum, or performance in high temperatures. Electric-field induction motors consist of a set of stator electrodes which induce opposite charges onto a movable rotor surface. In earlier work, rotor surfaces for electric-field induction motors have been made of single continuum materials, which are limited in possible resistivity, permittivity and circuitry characteristics. To enhance design freedom, we develop a rotor for electric-field-based machines which may be constructed out of discrete circuit components between a finite number of conductive vanes. Magnetic-field induction motors, which are common in machinery, often utilize ``deep bar'' rotors, consisting of conducting bars which decrease the rotor time constant with increasing frequency using the skin depth effect. We propose, analyze, design and demonstrate a macro-scale electric-field induction motor which uses circuitry on the rotor surface to emulate the ``deep bar'' design, providing improved torque over a wide range of speeds.

0.30

Explainable Machine Learning for Multilayer Planar Winding Inductance Estimation

cs.LG ·2026-09-29 ·Spyros Rigas, Theofilos Papadopoulos, Georgios Alexandridis, Antonios Antonopoulos
code/data similarity 0.45
Abstract · 10 pages

Rapid and accurate self-inductance estimation for multilayer rectangle-shaped planar windings is essential for modern high-frequency power converters, yet traditional workflows rely on complex mathematical equations, rigid monomial formulas or unexplainable black-box machine learning (ML) models that degrade severely outside their training domain. This paper introduces an explainable ML framework unifying post-hoc feature attribution (SHAP and permutation importance) with Kolmogorov-Arnold Network-guided symbolic regression via the SR-KAN framework to discover closed-form analytical equations without prior structural assumptions. Evaluated on a new open-source dataset of over 10,000 Finite Element Analysis (FEA) simulations across seven out-of-distribution (OOD) classes, standard tree-based ensembles exhibit severe extrapolation errors (> 36%), whereas the unconstrained SR-KAN expression achieves a robust OOD relative error of 8.22%. Experimental verification across 55 physical printed circuit board prototypes (up to 8 layers, with inductances from 4.11 μH to 559.27 μH) confirms that the KAN-discovered expression translates effectively to real-world hardware, predicting inductance with a mean absolute relative error of 6.26%. To support reproducible research, the complete FEA simulation dataset and prototype measurements are released open-source.

0.37

Parameter-Robust Sensorless Control of IPMSM Drives With Adaptive Flux Observer

eess.SY ·2026-09-30 ·Fobao Zhou, Zhenxiao Yin, Xueyan Wang, Yang Shen, Yuanfeng Qu +1 more
similarity 0.43
Abstract

To address parameter sensitivity commonly in interior permanent magnet synchronous motor (IPMSM) sensorless control, this paper proposes a parameter-robust control framework by extending the adaptive flux observer from surface-mounted PMSM to salient-pole machines. First, parameter mismatches are interpreted as an equivalent flux vector with $d$-axis and $q$-axis components. Permanent magnet flux, $d$-axis inductance, and resistance mismatches are mapped to the $d$-axis flux component, whereas $q$-axis inductance mismatch is mapped to the $q$-axis component. Then, a scalar adaptive flux update is designed to compensate the $d$-axis flux variation by tracking the equivalent flux magnitude. Since the $q$-axis component rotates the observed flux direction and cannot be eliminated by scalar adaptation, a high-frequency $q$-axis voltage injection method is introduced to identify the $q$-axis inductance. Meanwhile, stability analysis proves bounded equivalent flux magnitude tracking and identifies the residual tangential flux responsible for position error. Finally, experimental results show that the proposed method does not require precise resistance, $d$-axis inductance, or flux, while the $q$-axis inductance is provided by online identification.

0.10

Experimental and Signal Processing Techniques for Fault Diagnosis on a Small Horizontal-Axis Wind Turbine Generator

eess.SP ·2026-08-28 ·Francesco Natili, Francesco Castellani, Davide Astolfi, Matteo Becchetti
publishedunusual similarity 0.40
Abstract

Small HAWT is a technology characterized by non-trivial critical points, basically because it is targeted for domestic use and therefore cheap manufacturing and control must conjugate with good efficiency under possibly complex flow conditions (especially in urban environment). Therefore, dynamical control optimization and noise and vibration mitigation are pressing issues for this kind of technology. Despite it is peculiar of small HAWTs that the generator constitutes a non-negligible fraction of the total mass and therefore the electromechanical coupling is relevant, condition monitoring of small HAWT generators is an overlooked topic. The present work is a test case study of damage diagnosis on a permanent magnet generator of a HAWT having 3 kW of maximum power and 2 meters of rotor diameter. The experimental analysis is conducted through wind tunnel tests and on a generator test rig where a damaged and an undamaged generators have been driven at different rotational speeds. Vibration measurements are collected in the wind tunnel through radial accelerometers near the rear bearing of the shaft and in the test rig through uni-axial accelerometers (fixed in radial positions, in order to be aligned with front and rear bearings). The test rig data result being particularly useful for studying the low-frequency tail of the vibration spectrum, where the characteristic frequencies of the bearing are located. The experimental data are analyzed in the time and frequency domain for feature extraction: a fault in the cage of the bearing supporting the generator is diagnosed using in particular the spectral coherence analysis.

0.64

Temporal Regression-Based Model-Free Sensorless Control of Permanent Magnet Synchronous Motor

eess.SY ·2026-09-24 ·Fobao Zhou, Yang Shen, Xueyan Wang, Zhenxiao Yin, Yujia Zhang +2 more
similarity 0.40
Abstract

To address the widespread sensitivity of surface-mounted permanent magnet synchronous motor (SPMSM) sensorless control to motor parameters, this paper proposes a temporal regression-based model-free sensorless control (TFC) method. First, voltage integrals and current increments over consecutive short intervals are stacked to construct a finite window regression, in which the unknown stator inductance appears as a common scalar coefficient. Second, a projection operator constructed from the stacked current increments eliminates the inductance term, and a least-squares formulation is developed to reconstruct the rotor flux vector. Meanwhile, the analysis of the projected regression and current-flux geometry establishes a two-dimensional direction vector whose components share a common amplitude containing the stator resistance and flux linkage. This amplitude cancels during position extraction. By setting the resistance reference to zero, the proposed method estimates the position without specifying the stator resistance, inductance, or flux linkage. Finally, experimental results verify the effectiveness of the proposed TFC method.

0.32

CAHR-Net: Condition-Adaptive Hysteresis Reconstruction for Compact and Interpretable Magnetic Core Loss Modeling

cs.LG ·2026-09-02 ·Chunye Gong, Cong Yao
publishedunusual similarity 0.40
Abstract · 10 pages, 6 figures, 5 tables

Magnetic core loss originates in the hysteresis loop: the energy dissipated per excitation cycle equals the loop area, and frequency, temperature, and waveform shape set the loss by reshaping the loop geometry. Most existing models let these conditions act only on a terminal scalar - empirical equations fold them into fitted exponents, and data-driven predictors append them to encoded features - so no intermediate hysteresis representation remains for the conditions to reshape. This paper proposes CAHR-Net, a condition-adaptive hysteresis reconstruction network that injects the operating conditions where they physically act. It preserves the interpretable chain from flux density waveform to magnetic field reconstruction, loop-area integration, and power loss estimation, and uses feature-wise linear modulation to inject frequency, temperature, and waveform statistics into the intermediate reconstruction representation. A matched large-batch training protocol based on AdamW, cosine scheduling, and a staged reconstruction-to-power-loss objective is also reported, because the modulation pathway takes effect only within it. On the MagNet final A-E material protocol, CAHR-Net attains an average p95 relative error of 6.89% with only 1874 parameters, the lowest among all compared methods, together with a lower worst-material p95 than the strongest black-box solution at about 48x fewer parameters; it reduces the average p95 of the physical reconstruction backbone from 7.47% to 6.89% and the p95 of material D, the most difficult material, from 16.40% to 14.87%. Ablation and condition-slice analyses attribute the improvement to the coupling of physical loop reconstruction, structured condition modulation, and the matched optimization trajectory.

0.62

Physics-Guided Inferencer-in-the-Loop Digital-Twin for Real-Time Adaptive Emulation of Nonlinear PMSMs

eess.SY ·2026-10-28 ·Songyang Zhang, Yuzhong Zhang, Venkata Dinavahi
similarity 0.39
Abstract

A real-time digital-twin (RTDT) of a permanent magnet synchronous machine (PMSM) allows drive controllers to be tested in hardware-in-the-loop (HIL) before they meet the real machine. Its machine model rests on identified parameters or flux look-up tables (LUTs) from finite-element analysis (FEA) or characterization tests; the maps are regenerated offline when the machine changes, and online estimators track a few parameters such as resistance and PM flux. This article makes the executed model learnable from reference data. A physics-guided machine learning (PGML) network advances the currents and predicts torque in one step, trained with analytical one-step labels. In the proposed Inferencer-in-the-Loop (IIL) architecture, a GPU retrains the network while a field-programmable gate array (FPGA) executes the last accepted weights. For damper circuits, shifted parameters, and an FEA-calibrated saturated machine, one kernel form reaches average normalized mean absolute errors (NMAEs) of 0.19%-0.67% at measured FPGA kernel latencies of 0.30-0.34 $μ$s, and retraining for a shifted machine nears its final loss within 94 s. On a magnetically linear 200-W drive, a residual form corrects the analytical step and learns its physical parameters from operating data; each step takes under 2.5 $μ$s, 20 times faster than real time and ahead of the physical drive's measurements even at 20-kHz sampling. On six held-out runs (1193 s), its $i_q$ error is 5.9%-9.4% of measured RMS, against 10.4%-13.2% for an independently fitted grey-box model, and over 30 min of loaded heating its online-updated heads track a 4.1% winding-resistance rise with an RMS error of 0.44 m$Ω$.

0.29

Stray Losses in Power Transformers: A Comparative Study of Modeling Frameworks for Mild Steel

eess.SY ·2026-11-03 ·Micha Swaanen, Timo Overboom, Siamak Pourkeivannour, Tom Huiskamp, Guus Pemen
benchmarkunusual similarity 0.39
Abstract · 13 pages, 18 figures. Submitted to IEEE Transactions on Magnetics

Accurately predicting eddy-current and hysteresis losses in mild steel components such as the structural parts and tank of power transformers remains a challenge in transformer design. Conventional numerical approaches for eddy-current loss analysis require discretization at a fraction of the skin depth. While accurate, such fine volumetric mesh becomes computationally prohibitive for large power transformers. Moreover, hysteresis loss is not always included in this analysis. To investigate the trade-off between computational cost and accuracy, this work presents a comparative analysis of eight distinct modeling frameworks for predicting both eddy-current and hysteresis losses in mild steel. These include efficient methods avoiding meshing, such as standard impedance boundary conditions, and more accurate approaches retaining full volumetric meshing, namely complex permeability, nonlinear single-valued B-H curve, and Jiles-Atherton hysteresis modeling. To accurately represent the material's electromagnetic behavior, the properties of the mild steel used are measured directly from samples. Finally, loss measurements are conducted to benchmark all eight frameworks, demonstrating mean absolute percentage errors between predictions and measurements generally below 20%.

0.33