CS Paper Radar

Pressure Drop: Gravity Vector Estimation from a Distributed Barometric Pressure Sensor Array

William Dubois, Nicolas Lauzon, Johann Laconte, François Pomerleau

cs.RO ·submitted 2026-11-17 17:38 UTC · v1

Abstract

While gravity is often used in mobile robotics as a global constraint for Simultaneous Localization and Mapping (SLAM) algorithms, most estimation methods rely on indirect observation of the gravity vector. In this paper, we propose the use of altimeter measurements to directly observe the direction of the gravity vector. We provide a theoretical evaluation of the estimation noise and validate it through extensive experimental data, along with an evaluation of the impact of intersensor distance on our gravity vector estimates. Experimental results demonstrate that a median error of $0.87^\circ$ on the tilt estimation can be achieved with our system in semi-static scenarios. Furthermore, we demonstrate the potential of this approach by comparing it with state-of-the-art methods based on Inertial Measurement Units (IMUs). We highlight that we achieve similar performance to that of IMU-based systems in highly dynamic scenarios and even outperform in specific cases of accelerometer measurement saturation. Finally, an additional experiment shows the potential use within a robotic system through the integration into an Iterative Closest Point (ICP) algorithm.

Comment
8 pages, 6 figures, submitted to IEEE ICRA 2027

Closest papers

Nearest neighbours by meaning across the whole index.

Design and Implementation of a Kalman Filter-Infused Algorithm for Tilt Estimation

cs.CV cs.ROeess.SPeess.SY ·2026-09-01 ·Yuehan Ma, Hongji Dai
similarity 0.65
Abstract · 12 pages, 24 figures, 10 references

Accurate tilt angle estimation is important in many engineering applications, such as robotics, motion tracking, and embedded control systems. However, measurements from low-cost inertial sensors are often degraded by noise and drift. This paper presents a single-axis tilt angle estimation system based on the MPU6050 inertial measurement unit, implemented on an RP2040 microcontroller platform, with sensor fusion achieved through a Kalman filter. The accelerometer provides a direct estimate of tilt angle from gravity but is sensitive to noise and short-term fluctuations. The gyroscope provides smooth angular rate measurements, but integration over time introduces drift. To overcome these limitations, a Kalman filter is used to combine measurements from both sensors, leveraging the long-term stability of the accelerometer and the short-term smoothness of the gyroscope. Both simulation and hardware experiments are performed. In simulation, sensor noise and drift are modeled to evaluate the filter performance under control conditions. In the hardware implementation, real-time MPU6050 data is acquired and processed by the RP2040 platform, and the estimated tilt angle is compared with accelerometer-only and gyroscope-only outputs. The results show that the proposed method effectively reduces noise measurements and suppresses long-term drift while preserving good dynamic response. Overall, the system provides more stable and accurate tilt estimation than either sensor alone, demonstrating a practical and accessible approach for Kalman filter based sensor fusion in embedded application. This manuscript is a preprint version of the work. Keywords: Kalman Filter, Accelerometer, Gyroscope, Noise Reduction, Angle Tracking

0.27

A Tightly Coupled Magnetic-Inertial SLAM System for Field Robots

cs.RO eess.SP ·2026-11-02 ·Chuan Huang, Tongxing Peng
similarity 0.63
Abstract

Field robots operating in mines, tunnels, and disaster areas require reliable localization despite GNSS denial and degraded camera and LiDAR measurements caused by dust, smoke, or poor illumination. Missions involving both ground and aerial robots further motivate complementary sensing modalities that do not depend on visibility, preinstalled infrastructure, or wheel contact. This letter presents MISLAM, a tightly coupled magnetic-inertial simultaneous localization and mapping system using an IMU and a nine-magnetometer array, without relying on external odometry or platform-specific motion assumptions. The system combines the inertial navigation model with local polynomial magnetic-field models for short-term motion estimation and a global Gaussian process model for drift correction using an error-state Kalman filter. Offline evaluation on three indoor datasets collected with a handheld rig shows reductions in total endpoint closure error of 45.7% - 78.0% relative to magnetic-inertial odometry. Under poor illumination, MISLAM maintains tracking after visual-inertial odometry fails, achieving a horizontal closure error of 0.332 m, although vertical drift remains a limitation. These results support magnetic-inertial SLAM as a complementary localization modality for robotic sensor suites operating under degraded visual conditions.

0.16

Gravity-aware partially calibrated absolute pose estimation from affine- or rotation-covariant features

cs.CV ·2026-08-20 ·Marcus Valtonen Örnhag, Alberto Jaenal, Stefan Adalbjörnsson
top venue similarity 0.63
Abstract · European Conference on Computer Vision 2026

Inertial measurement units (IMUs) are now standard in most consumer devices, such as smartphones, drones, and extended reality (XR) headsets. By fusing visual and inertial data, localization systems gain significantly in speed and robustness compared to vision-only or IMU-only approaches. However, traditional pose estimation methods fail to utilize the local geometric information embedded in feature descriptors like SIFT. Recent work has proved the advantages of leveraging this information for relative and absolute pose estimation, but its application to partially calibrated absolute pose estimation remains unexplored. In this paper, we derive novel constraints for joint estimation of absolute pose and focal length, making use of a gravity vector obtained from IMU data and the feature-induced local geometry, which we use to construct two efficient solvers: UP1PfAC, that operates given a single affine correspondence and UP2PfORI, which requires two orientation-covariant features. Unlike traditional, semi-calibrated absolute pose methods requiring four point correspondences, our solvers benefit from fewer samples and lower computational cost, simplifying robust estimation in modern RANSAC-like frameworks. We evaluate the proposed solvers against the state-of-the-art on large-scale public datasets and demonstrate that our method achieves fast and accurate localization and focal length estimation.

0.37

Calibration-free IMU-based Relative Orientation Estimation under Dynamic Human Motion

cs.RO eess.SY ·2026-10-22 ·Ruiyuan Li, Hassan Osman, Ajay Seth, Manon Kok
similarity 0.60
Abstract · 8 pages, 7 figures, 1 table. Submitted to IEEE Sensors Journal

Recent magnetometer-free inertial measurement unit (IMU) methods can reduce drift in joint motion estimation using rigid-body constraints, but they typically require pre-calibrated sensor locations, assumptions of specific joint models (e.g., hinge joints) or limited motion types, or an external reference for global orientation. Furthermore, challenges related to high-frequency impacts (e.g. at foot strikes during gait) and numerical differentiation of noisy measurements have not been explicitly addressed. We propose an extended Kalman filter that estimates relative IMU orientation and sensor location simultaneously, requiring neither offline sensor location calibration nor a global orientation anchor. A systematic simulation study shows that the quality of the relative orientation and the sensor location estimates depends on different motion-intensity sources: the joint center acceleration and the relative angular velocity, respectively. A low-pass filter (LPF) is used to mitigate real-signal outliers before applying the rigid-body constraint. When applied to the OpenSense dataset with real IMU measurements across four subjects with three lower-body joint types during walking and complex tasks including various motion types, the proposed method achieves an overall relative orientation error of 2.61°, compared with 10.40° for a baseline using offline-estimated sensor locations and 7.43° for a baseline using marker-derived sensor locations. These results show that the proposed calibration-free estimation framework handles real IMU data effectively and achieves accurate relative orientation without offline sensor location calibration.

0.16

Metric Scale for Insta360 Structure-from-Motion from the Camera's Embedded IMU

cs.CV ·2026-10-26 ·Davide Cuttini, Diego Di Tommaso, Alessio Antoniacomi, Luca Simonetti
benchmarkcode/data similarity 0.60
Abstract · 17 pages, 9 figures, 4 tables. Dataset: https://huggingface.co/datasets/OverTheReality/OverMaps360_50

Structure-from-motion (SfM) from the dual-fisheye video of a consumer 360-degree camera recovers geometry only up to a similarity transform; in the pipeline considered here, metric scale is obtained from smartphone ARKit or ARCore poses captured alongside the camera. This paper evaluates a self-contained alternative: the IMU embedded in the Insta360 X5 and X6, recorded at 1 kHz. The sensor is characterised (noise density, camera-IMU synchronisation, accelerometer scale factor, bias stability), the camera-IMU rotation and frame timing are estimated from the data, and the scale is recovered by a linear visual-inertial alignment over the SfM poses of a whole survey. The standard formulation, with gravity and accelerometer bias shared across the survey, overestimates the scale by 3.4% on average; estimating each contiguous segment independently and averaging removes the bias. On nine surveys with a co-mounted LiDAR scanner the inertial scale deviates from the LiDAR by 0.81% in mean absolute error, against 1.94% for the smartphone scale; on printed fiducial markers both agree within the 1% uncertainty of the target. On the reference trajectories of thirty sequences of a public benchmark, brought to scales of 1/40, 1 and 40, the estimator recovers the metric scale with a mean error of -0.07% and a standard deviation of 1.28%. On fifty production surveys where the smartphone is the only reference, the two scales agree to a standard deviation of 2.3%, the inertial scale being 0.3% lower on average; the difference is uncorrelated with run length, grows with the extent of the smartphone anchor, and cannot be attributed to either reference. An ablation over window construction and a comparison with monocular metric-depth networks complete the study.

0.34

GLIO2: A GPU-Parallelized Tightly-Coupled LiDAR-Inertial-GNSS System for Robust and Real-Time Global Localization and Mapping

cs.RO ·2026-10-08 ·Qi Zhang, Xikun Liu, Qijun Qin, Xiangru Wang, Junzhe Wang +3 more
similarity 0.60
Abstract · 23 pages, 16 figures, 8 tables; includes appendices

Globally consistent, real-time state estimation in large-scale, perceptually degraded environments is essential for autonomous vehicles and aerial robots, and requires fusing LiDAR, inertial, and GNSS measurements. Existing fusion methods, however, share a scan-to-map front-end with two failure modes. First, each scan is aligned to an incrementally built map that drifts under degeneracy, and once the estimate diverges the error is irrecoverable. Second, even without divergence, a registration biased by dynamic objects or wrong correspondences is propagated as a single pose constraint with an over-confident covariance, leaving its correspondences unavailable for GNSS to re-weight or relinearize. We propose GLIO2, a tightly-coupled LiDAR-Inertial-GNSS system whose GPU-parallel front-end jointly optimizes scan-to-multiscan LiDAR, IMU pre-integration, and raw GNSS measurements in a single sliding-window factor graph, sustaining real-time operation on edge hardware. A complementary offline back-end reuses the same cached factors to refine the entire trajectory in batch, completing the 30-min, 4.51-km UrbanNav Whampoa sequence in about 24 s. Across three public benchmarks (UrbanNav, MARS-LVIG, M3DGR) and self-collected UAV and vehicle data, GLIO2 attains the best overall accuracy among evaluated systems. On a 5.66-km bridge traversed at up to 96 km/h, where every competing baseline diverges under LiDAR degeneracy, it maintains 1.6 m horizontal accuracy. On an NVIDIA Jetson Orin NX, the full pipeline runs at about 25 Hz (39.60 ms per scan). The source code and datasets will be released.

0.21

The Setting of IMU Parameters in Kalman Filtering-based Information Fusion

cs.RO eess.SY ·2026-08-17 ·Qiang Hu, Yanhua Zou, Shuaiyi Huo, Haibo Ge, Wei Ouyang
similarity 0.59
Abstract · 2026 International Conference on Guidance, Navigation and Control

The setting or tuning of specifications for the inertial measurement unit (IMU) is tricky in sensor fusion. The underneath conundrum is caused by the fact that the working condition of IMU is more complex than the stationary calibration scenario. Since the noises and biases instabilities calibrated under static condition cannot accommodate other cases, the effective tuning of IMU parameters largely hinges on the experience or profound understanding of the system. In the current work, the setting method of IMU parameters based on Allan variance calibration is delved into within the Kalman filtering framework. Specifically, the relationship between the power sepctral density and Allan variance is leveraged in formulating the process uncertainty in continuous-time filtering. Three typical IMU-based sensor fusion systems, including INS/GNSS integration, LiDAR-inertial odometry, and visual-inertial odometry are considered to show the feasibility and effectiveness of this parameter setting process.

0.23

Visual-Inertial Odometry for Ground Robots with Dynamic Camera-IMU Extrinsic Calibration

cs.RO ·2026-10-18 ·Bo Dong
similarity 0.59
Abstract

Visual-inertial odometry systems are often constrained by the assumption that sensors are rigidly mounted, which limits their adaptability in practical scenarios involving structural motion. To address this limitation, this paper investigates time-varying camera-IMU extrinsic calibration. First, a dynamic camera-IMU extrinsic calibration method based on the Denavit-Hartenberg convention is proposed by incorporating the robot kinematic model. Second, a two-step initialization strategy is developed to efficiently estimate the initial joint angles, providing a reliable starting point for subsequent extrinsic parameter optimization and enabling online estimation of timevarying camera-IMU extrinsic parameters. Simulation experiments demonstrate that the proposed framework can effectively accommodate variations in camera-IMU extrinsic parameters while maintaining competitive localization accuracy.

0.14