CS Paper Radar

Python-based RTL Generator Demonstrated on a Low-IF 2-FSK Wireless Communication System

Brandon P. Hippe, David C. Burnett

eess.SY ·submitted 2026-08-17 18:41 UTC · v1

Abstract

Hardware optimization is critical in the design of efficient wireless communication systems. Wireless communication hardware often consumes a significant fraction of the total system's power budget, with much of this power used in circuits that reduce various types of noise, particularly in the analog front end. The Single-Chip Micro Mote, or SCuM, uses a crystal-free radio architecture and makes design trade-offs that favor power consumption over noise performance while maintaining standards compatibility with popular Internet-of-Things (IoT) protocols such as IEEE 802.15.4 and Bluetooth Low Energy. In the continued development of SCuM, we recognize that the digital baseband hardware developed can be more closely optimized with the architecture of the chip. In this paper, we present an extensible Python-based RTL generator that is closely linked to simulation and testing environments. This approach provides flexibility for use on different hardware platforms, such as tape-outs and FPGA implementations, and has promise in AI-assisted design workflows.

Closest papers

Nearest neighbours by meaning across the whole index.

A LoRa-Compatible Receiver with Programmable Noise-Power Trade-Off and Integrated Wake-Up Mode

cs.AR ·2026-10-14 ·Marco Gonzalez, Pol Maistriaux, Jérôme Louveaux, David Bol
similarity 0.56
Abstract · 13 pages, 19 figures, removed mentions to IEEE

Programmable receivers allow an optimal performance in the variable conditions of the wireless channel. An extensive analysis of their noise-power trade-off enables the development of a main receiver with embedded wake-up circuitry. This makes the seamless integration of wake-up receivers (WuRXs) in RF receivers possible, avoiding power, area, complexity, and cost overheads in the system. In this paper, we propose the first LoRa-compatible receiver with an integrated wake-up mode and a programmable noise-power trade-off. In main-receiver mode, it consumes 4.57 mW for a sensitivity of -138 dBm, but it can save up to 62.6% of power consumption at the cost of an 8.3-dB sensitivity degradation. In wake-up mode, sensitivity down to -126 dBm is achieved for a 32-ms latency and 1.5 mW of power consumption. The power consumption remains relatively high due to a sub-optimal design of the the phase-locked loop (PLL). In the end, the wake-up mode consumes 3X less than the lowest-noise configuration in main-receiver mode.

0.28

LoopHIL: Looping Hardware into LLM-assisted Agents for Wireless Embedded Systems

cs.NI cs.AIcs.ARcs.SE ·2026-10-16 ·Dhairya Shah, Spanddhana Sara, Savitha Viswanadh Kandala, Ambuj Varshney
similarity 0.52
Abstract · 8 pages, 8 figures, 4 tables. Under review

LLM agents are widely used for software development and debugging, but their adoption in embedded systems, especially for wireless tasks, remains limited. This is because embedded development requires hardware-in-the-loop testing. Agents cannot directly observe the spectrum, probe pins, or measure power, so they cannot verify wireless link functionality; currently, human engineers perform this verification. We systematically evaluate whether LLM agents can establish wireless links when provided with hardware access. We introduce LoopHIL, a framework that lets agents control a multi-device RF bench, monitor it with a spectrum analyzer, logic analyzer, and energy meter, and validate links against a verification ladder, all within code-enforced safety limits. Across four increasingly complex tasks, from generating a carrier to backscatter decoding by a commercial receiver, and using six models from two vendors, hardware-in-the-loop increases task completion rates from 54% to 79% and from 17% to 83% on the most challenging task. It also halves task time and output tokens. With debugging tools, agents decrease tag power consumption by up to 96%. However, small models often report unverified claims, so independent hardware checks remain necessary.

0.56

uhd-rfsoc: Bringing Off-the-Shelf RFSoC Boards to Unmodified UHD Applications

cs.NI cs.AReess.SP ·2026-11-13 ·Wei Cheng, Yiming Li, Junyao Zheng, Cheng-Bin Chen, Tingjun Chen
code/data similarity 0.52
Abstract

Next-generation wireless research relies on software-defined radios (SDRs) with more channels and larger bandwidth. The USRP family is one of the most widely used SDR platforms, and much of the wireless software ecosystem is built on top of the USRP hardware driver (UHD). However, each USRP model comes with a fixed channel count, bandwidth, and streaming capability. Off-the-shelf radio frequency system-on-chip (RFSoC) boards, on the other hand, integrate up to 16 analog-to-digital converters (ADCs) and 16 digital-to-analog converters (DACs) operating at several gigasamples per second (GS/s), but existing UHD applications cannot directly use them. We present uhd-rfsoc, an open-source FPGA design and host software stack that turns these boards, including the 16-channel ZCU216 and the RFSoC 4x2, into standard UHD devices without modifying UHD. Through standard UHD calls, applications can configure the carrier frequency, channel count, the per-channel I/Q sample rate, and the wire format. uhd-rfsoc combines timestamped, flow-controlled sample transport in the FPGA with data plane development kit (DPDK) packet processing and vectorized sample conversion on x86 and Arm hosts. The built bitstreams for a number of RFSoC board configurations with varying RF data converter rates, channel counts, I/Q sample rates, and wire formats all successfully pass UHD's built-in streaming benchmarks. We further demonstrate compatibility with unmodified GNU Radio flowgraphs, a custom GPU-accelerated transceiver digital signal processing pipeline, as well as the OCUDU and Duranta 5G radio access network stacks using both software and commodity user equipment.

0.35

Virtualized 5G Tesbed using OpenAirInterface: Tutorial and Benchmarking Tests

cs.NI ·2026-09-11 ·M. Dória, V. Sousa, A. Campos, N. Oliveira, P. Eduardo +7 more
publishedbenchmarkhighly cited similarity 0.52
Abstract

The development of 5G and its evolutionary path to 6G brings virtualization as close as possible to the antennas. Native 3GPP systems are now software running at servers boosted by accelerator cards to cope with computationally intense signal processing. Meanwhile, the Radio Frequency (RF) front-end is still proprietary hardware, sheltering specific PHY-layer procedures like passband amplification/modulation. This approach takes advantage of the software's flexibility while keeping the complex microsecond signal processing performance from modern telecommunication systems. This paper provides tutorial material on the Core Network and Radio Access Network of OpenAirInterface (OAI) 5G stack on top of Universal Software Radio Peripheral (USRP) platforms. A set of blueprints showcases OAI's ability to provide a virtualized 5G network with different transmission capabilities and the possibility to use it with commercial mobile phones. Configuration discussions and throughput benchmark analyses follow installation and deployment instructions. Our results show that 5G prototyping using OAI and USRP frontends can lead to good reproducibility and consistent throughput.

0.49

Evaluating Wi-Fi HaLow for Next-Generation Capsule Endoscopy

eess.SY ·2026-10-25 ·Ziyao Zhou, Chen Shen, Tiancheng Cao, Hen-Wei Huang
similarity 0.51
Abstract

Capsule endoscopy is limited by its wireless link: insufficient throughput restricts image resolution and frame rate, whereas high-rate radios typically use higher carrier frequencies that experience greater attenuation through tissue. This work evaluates Wi-Fi HaLow (IEEE 802.11ah), a sub-GHz Wi-Fi standard, as an image link for capsule endoscopy. Across all tested combinations of modulation and coding scheme and bandwidth, the saturation TCP throughput reached 15.55 Mbps, and the fastest configuration also achieved the lowest energy per bit. Through power optimization strategies, the combined power consumption of the HaLow module and microcontroller at 1 frame per second (FPS) was reduced from 101.70 to 14.00 mW, which is comparable to that of Bluetooth Low Energy systems. In a simulated in vivo setting, the default rate control selected the highest tested MCS and bandwidth, indicating sufficient link quality; this configuration also had the lowest measured power in both the 1 FPS mode (13.59 mW) and the 30 FPS mode (174.21 mW). The capsule-to-receiver latency was 20.68 ms for a 24 KB frame, while the receiver-to-capsule latency was 4.77 ms for a command; this low-latency bidirectional communication supports real-time detection and manipulation for next-generation capsule endoscopy.

0.08

Open-source emulation-based test environment to settle O-RAN-compliant trials

cs.NI ·2026-09-16 ·Ramon Fontes, Allan Martins, Vicente Sousa, Kaio Dantas, Lucas Medeiros +9 more
published similarity 0.51
Abstract

Experimental tools are a key factor in both academic and industrial research communities to create design evaluations of new networking technologies that involve troubleshooting or changing the planning of deployed networks. Physical Software-Defined Radio (SDR) experimental platforms enable a design solution for the quick prototyping of wireless communication systems. However, SDR-based experimental platforms incur high costs, which leads to scalability limitations in the experimental settings. Having said this, network simulators, emulators, and new testbeds have attracted increasing attention. Emulation-based research prototyping can be distinguished from real communication networks and SDR-based platforms by allowing a tradeoff between cost and flexibility. This paper examines the Mininet-RAN emulation tool, which, as well as Radio Access Network (RAN) modeling, provides a way to test Open RAN Intelligent Controller (RIC) services without the need to deploy an entire RAN infrastructure. The Mininet-RAN creates virtual network elements, such as hosts, L2/L3 devices, controllers, and links, by combining some of the best emulator features, hardware testbeds, and simulators. By running the current code of standard practice Unix/Linux network applications and network stack, the Mininet-RAN enables real-world network data traffic patterns to be delivered to the RIC, regarding the most significant aspect of the dynamic generation of wireless system's KPIs. We provide the basic code of Mininet-RAN for the first two O-RAN Alliance-defined use cases involving V2X and UAV. The xApps are being implemented in O-RAN SC near-RT RIC, with Mininet-RAN which provides a closed-loop validation environment.

0.49

An FPGA-in-the-Loop Testbed for MU-MIMO OFDM Beamforming over Ray-Traced Wireless Channels

cs.NI ·2026-09-06 ·Drew Schlesener, Tolunay Seyfi, Fatemeh Afghah
similarity 0.51
Abstract

Wireless networks face ever expanding throughput demands from heterogeneous, high-density user populations, requiring beamforming algorithms that adapt to channel conditions with low latency. Validating such algorithms requires either costly over-the-air testbeds or simulation environments that lack the timing and resource constraints of real hardware, leaving a gap between algorithm design and hardware-realizable deployment. This work presents a frame-based hardware-in-the-loop (HIL) testbed that closes that gap by coupling an FPGA-based implementation of OFDM Waveforms with MU-MIMO beamforming to NVIDIA Sionna's ray-tracing channel simulator, enabling a physical base-station architecture to transmit and receive against a Sionna-rendered digital-twin propagation environment. Unlike prior work that validates beamforming algorithms either purely in simulation or on full RF testbeds, this architecture allows beamforming logic running on actual FPGA fabric to be evaluated under realistic, controllable, and repeatable channel conditions, including UE mobility and site-specific multi-path, without requiring an anechoic chamber or live RF front end. We detail the FPGA OFDM transmit/receive pipeline, the synchronization and data interface between the FPGA and the Sionna environment, and validation of signal quality under AWGN and ray-traced channel conditions, establishing this testbed as a platform for hardware-validated beamforming research.

0.26

Channel Modeling for Phase-Based Ranging

eess.SP ·2026-08-18 ·Till Droemmer, Markus Gardill
similarity 0.51
Abstract · 4 pages, 4 figures. Submitted to IEEE Radio and Wireless Week (RWW) 2027

This paper presents a Python-based simulation framework for the physical layer of Bluetooth Channel Sounding in accordance with Bluetooth Core Specification v6.2. The simulator implements Mode 3 phase-based ranging across 72 active tones in the 2.4 GHz ISM band and supports multiple propagation conditions, including free-space, static multipath, and IEEE 802.15.4a stochastic multipath channels. In addition, it models relevant hardware and interference effects such as phase noise, phase ramp, carrier frequency offset, IQ imbalance, ADC quantization, and narrowband interference from co-located Wi-Fi systems, with parameters derived from commercial SoC datasheets and field measurements. The framework enables controlled and repeatable analysis of physical layer effects that are difficult to isolate in over-the-air experiments and are not sufficiently represented in existing higher-level simulation tools. This work focuses exclusively on physical layer signal generation, channel modeling, and impairment injection, providing a foundation for future studies on Bluetooth Channel Sounding ranging and localization algorithms.

0.28