CS Paper Radar

A LoRa-Compatible Receiver with Programmable Noise-Power Trade-Off and Integrated Wake-Up Mode

Marco Gonzalez, Pol Maistriaux, Jérôme Louveaux, David Bol

cs.AR ·submitted 2026-10-14 15:32 UTC · v2

Abstract

Programmable receivers allow an optimal performance in the variable conditions of the wireless channel. An extensive analysis of their noise-power trade-off enables the development of a main receiver with embedded wake-up circuitry. This makes the seamless integration of wake-up receivers (WuRXs) in RF receivers possible, avoiding power, area, complexity, and cost overheads in the system. In this paper, we propose the first LoRa-compatible receiver with an integrated wake-up mode and a programmable noise-power trade-off. In main-receiver mode, it consumes 4.57 mW for a sensitivity of -138 dBm, but it can save up to 62.6% of power consumption at the cost of an 8.3-dB sensitivity degradation. In wake-up mode, sensitivity down to -126 dBm is achieved for a 32-ms latency and 1.5 mW of power consumption. The power consumption remains relatively high due to a sub-optimal design of the the phase-locked loop (PLL). In the end, the wake-up mode consumes 3X less than the lowest-noise configuration in main-receiver mode.

Comment
13 pages, 19 figures, removed mentions to IEEE

Closest papers

Nearest neighbours by meaning across the whole index.

Adaptive Wake-on-Radio Communication for Batteryless IoT Systems

cs.NI ·2026-11-16 ·Hooman Sarvghadi, Juan Felipe Gutiérrez Gómez, Negar Halakou, Nasrin Razmi, Andrés Gómez
published similarity 0.60
Abstract · This is an open-access, author-archived version of a manuscript published in ApplePies 2026 Conference

Batteryless Internet of Things (IoT) systems powered by energy harvesting require communication mechanisms that dynamically adapt to fluctuating energy availability while maintaining ultra-low-power operation. This paper presents a Wake-on-Radio (WoR) communication framework for low-power intermittent IoT systems in which the node's communication state adapts to its stored energy. The framework uses a batteryless IoT node that integrates a photovoltaic harvester, a 570 $μ$F capacitor, two voltage supervisors, and a microcontroller. The voltage supervisors drive an energy-aware finite state machine that switches the node between Shutdown, Low-Power Listening (LPL), Transmit, and Receive modes. The proposed system employs the integrated WoR capability of the transceiver, eliminating the need for additional wake-up hardware. For the evaluated traffic conditions and an LPL wake-up rate of 16 Hz, the measured power consumption is approximately 1.2 $μ$W in the Shutdown mode, 300 $μ$W during LPL, 531 $μ$W for reception, and 627 $μ$W for transmission. System-level experiments under solar-harvesting operation validate the proposed framework, demonstrating reliable bidirectional communication with no packet losses observed across repeated runs at a harvested input power of 1.2 mW.

0.30

Fundamentals of Energy-Efficient Hardware Configurations for Wireless Links with Sleep Modes

cs.IT ·2026-09-10 ·Anders Enqvist, Özlem Tuğfe Demir, Cicek Cavdar, Emil Björnson
published similarity 0.60
Abstract · 13 pages, 8 figures. A preliminary version was presented at IEEE VTC2024-Spring

In this paper, we examine the energy efficiency (EE) of a base station (BS) with multiple antennas. We use a state-of-the-art power consumption (PC) model that captures the passive and active parts of the transceiver circuitry, including the effects of radiated power, signal processing, and passive consumption. The paper treats the transmit power, bandwidth, and number of antennas as the optimization variables. We provide novel closed-form solutions for the optimal ratios of power per unit bandwidth and power per transmit antenna, and discover a new relationship in which the radiated power equals the total transceiver power at the EE-optimal operating point. A central finding is that the EE-optimal signal-to-noise ratio (SNR) collapses to a universal numerical constant of approximately 5.93 dB, independent of channel and hardware parameters. We present an algorithm that jointly optimizes the three design variables to achieve maximum EE under practical constraints, and provide analytical insight into whether maximum power or maximum bandwidth is optimal and how many antennas a BS should utilize. We further extend the optimization framework to incorporate quality-of-service (QoS) requirements and three advanced sleep modes of varying depth: absolute sleep, deep sleep, and idle mode. We characterize the optimal hardware configuration for each mode and determine when the rush-to-sleep strategy, which transmits briefly at the EE-optimal active configuration and sleeps the rest of the time, is optimal. Incorporating wake-up transition delays, we reveal how latency constraints and sleep-mode-specific transition times jointly dictate the optimal sleep mode for data packets with absolute deadlines. Together, these results indicate that energy-efficient operation requires treating transmission and sleep as a single coupled optimization.

0.58

Python-based RTL Generator Demonstrated on a Low-IF 2-FSK Wireless Communication System

eess.SY ·2026-08-17 ·Brandon P. Hippe, David C. Burnett
similarity 0.56
Abstract

Hardware optimization is critical in the design of efficient wireless communication systems. Wireless communication hardware often consumes a significant fraction of the total system's power budget, with much of this power used in circuits that reduce various types of noise, particularly in the analog front end. The Single-Chip Micro Mote, or SCuM, uses a crystal-free radio architecture and makes design trade-offs that favor power consumption over noise performance while maintaining standards compatibility with popular Internet-of-Things (IoT) protocols such as IEEE 802.15.4 and Bluetooth Low Energy. In the continued development of SCuM, we recognize that the digital baseband hardware developed can be more closely optimized with the architecture of the chip. In this paper, we present an extensible Python-based RTL generator that is closely linked to simulation and testing environments. This approach provides flexibility for use on different hardware platforms, such as tape-outs and FPGA implementations, and has promise in AI-assisted design workflows.

0.25

Power Scaling Across Link Utilization with GPAM-4 Signaling and Event-Driven Reception

cs.ET ·2026-11-14 ·Maya Mekel, Jeries Mattar, Nicolas Wainstein
unusual similarity 0.52
Abstract

This work highlights the potential of combining event-based signaling with event-driven reception to achieve receiver power scaling across link utilization, without requiring wake-up, locking, or data-rate reconfiguration. The approach is demonstrated using the proposed four-level Gaussian pulse-amplitude modulation (GPAM-4) scheme and a corresponding event-driven receiver. By employing a resettable ring voltage-controlled oscillator (RRVCO) as its front end, the receiver achieves inherently event-driven symbol measurement, initiated directly by each received pulse. Symbols are decoded directly from the final RRVCO phase state, eliminating a counter-based back end. Simulated in 28-nm CMOS, the receiver power is evaluated across a $100\times$ range of effective data rates---from 0.15 mW at the peak rate of 8 Gb/s, down to 2.5 $μ$W under active/idle operation and 1.6 $μ$W under data rate change at 80 Mb/s. The receiver thus achieves power reductions of $59.5\times$ and $90.0\times$, while its energy per bit increases by only $1.68\times$ and $1.11\times$, respectively.

0.26

Centralized RAN for Future Low-Power Wide-Area Networks: A LoRa Case Study

eess.SP ·2026-08-24 ·Joachim Tapparel, Amavi Dossa, El Mehdi Amhoud, Andreas Burg
published similarity 0.52
Abstract · Accepted for publication in IEEE Internet of Things Magazine

In recent years, low-power wide-area network (LPWAN) technologies have gained significant traction as a connectivity option for Internet of Things (IoT) applications. While these networks have been successful in providing long-range, low-power, and low-cost connectivity, they currently face scalability, reliability, and efficiency challenges that require immediate attention. In this paper, we first identify important challenges for LPWANs. We then advocate for the introduction of a centralized radio access network (C-RAN) architecture tailored for LPWANs and present a proof-of-concept implementation and deployment of the proposed C-RAN for the widely popular long range (LoRa) standard. We also provide experimental results to demonstrate and quantify the increased sensitivity that can be obtained from joint processing of the baseband signals of multiple receivers, enabled by the proposed centralized architecture in quasi-static scenarios and drone-mounted transmitters.

0.35

Rethinking Battery-free Sensing Communication via Wake-up Radios

cs.NI ·2026-08-26 ·Gaosheng Liu
similarity 0.52
Abstract · This paper is not ready for publication

Battery-free sensors expose short, stochastic communication windows and may lose timing state whenever their main energy domain browns out. MagPie combines a microampere wake-up radio (WuR) with a separately backed low-power real-time clock (LP-RTC): the WuR widens the first-contact window, while the LP-RTC preserves the acquired phase for later exchanges. Energy gates, epoch-versioned schedules, and idempotent slot allocation extend this mechanism to static, single-hop All-to-One collection without a powered control anchor. The analysis accounts for role selection and duty-cycled listening, and bounds scheduled-retry tails only under explicit conditional quantile coverage. Evaluation separates three scopes. In independent, administratively censored simulation trials, MagPie completes 100/100 first rendezvous events in each of five trace-parameterized harvesting scenarios; Find completes 36-100/100. A single-collision-domain slotted-Aloha study shows that adaptive K is necessary at high contender density and reports mean, P95, and confidence intervals through 120 components. Finally, controlled STM32WL33 experiments validate alignment, clock persistence, and six-device slot execution, including an 11.05-hour functional run. The study does not claim measured end-to-end energy, ambient-harvesting performance, or multi-hop scalability; highly variable harvesting still limits collection because coordination cannot create missing energy.

0.27

Age of Information for Power-Saving Devices with DRX Mechanism

cs.NI cs.PF ·2026-11-06 ·Hung-Chun Lin, Kuang-Hsun Lin, Hung-Yu Wei
publishedtheoryhighly cited similarity 0.49
Abstract · 6 pages, 4 figures, 1 table. Published in IEEE ICC 2023

Reducing the power consumption of User Equipment (UE) has always been a crucial issue in communication systems. As a result, Discontinuous reception (DRX) is introduced in today's New Radio (NR) networks as a power-saving strategy. In addition, the variety of low latency applications in 6G makes the issue of maintaining data freshness increasingly important. This paper aims to study the relationship between freshness and power-saving. To capture the information freshness, we use Age of Information (AoI) as the performance metric. To our best knowledge, unlike previous studies focusing on power saving and delay trade-offs, this is the first study considering the impact of DRX on AoI. We solve the closed-form solution of the peak average AoI with the DRX mechanism. Moreover, we propose a parameters adjustment strategy. Based on the simulation validation, our proposed strategy can enable the UE to keep the AoI close to the theoretical lower bound AoI while achieving high power-saving efficiency.

0.64

Towards Energy-Neutral IoT Sensors: Low-Cost Chirp-Based Backscattering Node Using a COTS Microcontroller and Multi-Load Front-End

eess.SP ·2026-09-23 ·Tijl Schepens, Liesbet Van der Perre, Gilles Callebaut
similarity 0.48
Abstract

Backscatter communication has proven to be a key enabler for energy-neutral sensor nodes in the IoT. It allows ultra-low-power nodes to transmit sensor data by reflecting incident RF signals. Practical large-scale deployment requires hardware solutions that are both cost-efficient and widely available. This paper investigates the practical limits of implementing backscatter transmitters exclusively using COTS components. We compare a two-load and multi-load architecture in terms of hardware requirements, complexity and spectral efficiency highlighting the most important trade-offs. A multi-load backscatter architecture is developed using a resource constrained low-power microcontroller, levering DMA to achieve high switching speeds while minimizing processing overhead. Furthermore, we present a layout agnostic load design methodology based on scattering parameters, allowing precise control of the reflection coefficients. A prototype implementation demonstrates a successful backscatter transmission of a single-sideband chirp with reduced harmonic distortion. Measurement results show suppression of the backscattered carrier and the second sideband by 10 dBm. This demonstrates that low-cost sensor nodes can be built using COTS components enabling remote monitoring at extended lifetimes.

0.23