CS Paper Radar

System Identification of Admittance Models for Large Real-World Objects

Nathan I. Baum, Nathaniel G. Luttmer, Mark A. Minor

cs.RO ·submitted 2026-08-30 18:06 UTC · v1

Abstract

Simulation of admittance-type models requires physically consistent dynamic models that are rarely available for off-the-shelf, everyday objects, limiting the fidelity of haptic interfaces that rely on such simulations. This paper presents the first complete workflow for producing physically consistent models of large real-world objects with various constraints and mechanisms, guaranteeing physical consistency of inertia and friction parameters. The workflow separates each object and identifies the handle and body in two stages, requiring no torque sensors at hinges, axles, or other constrained joints. Models are produced for a heavy, closer-actuated door and a wheelbarrow, representing objects of differing constraint types and model complexity. The door is modeled using four-bar linkage kinematics and a fluid dynamics-based lumped parameter model including opening, backcheck, swing, and latch zones. The wheelbarrow is modeled as a rigid body with a spherical wheel and no slip during rolling. Handle estimation RMS errors were below 0.64 N and 0.042 Nm across both objects. Door body estimation had RMS error of 2.19 Nm and wheelbarrow body estimation had RMS error of 6.77 Nm.

Comment
8 pages, 7 figures,1 table

Closest papers

Nearest neighbours by meaning across the whole index.

Identification of the Steering and Speed Systems of a Four-Wheel-Steering Tractor for Optimal Control

eess.SY ·2026-09-04 ·Riikka Soitinaho, Timo Oksanen
similarity 0.54
Abstract

Model-based control design requires sufficiently accurate model of the system-to-be-controlled. This paper addresses the system identification of steering and speed control of a four-wheel-steering agricultural tractor for the purpose of developing path tracking control. To this end, we investigate the steering and speed control systems of the tractor. These are complex systems with digital, mechatronic, and hydraulic components challenging to model based on first principles. We take a data-driven approach to estimating the system models. The resulting model combines the kinematic model of the vehicle, actuators modelled as first-order systems, and estimated values for time constants and transport delays.

0.32

How Well Do Pseudo-Rigid Body Models Capture Real Plants? In-Field Validation of Simulated Blueberry Canes

cs.RO ·2026-09-12 ·Hannah Kolano, Chelse VanAtter, Wei Yang, Cindy Grimm, Joseph R. Davidson
similarity 0.51
Abstract

Many labor-intensive tasks in fruit production such as pruning require physically interacting with the plant (e.g., pushing, pulling, bending limbs, etc.). Due to increasing labor shortages, there is widespread interest in the adoption of robotics in this area. When the robot must physically interact with the system, a deformable model of the plant is beneficial. Coupled, spring-loaded beams have been used in prior work to build deformable plant models in simulation for learning, planning, and control, but this approach has rarely been validated against the mechanical properties of real-world plants. In this paper, we use this rigid-body model, grounded in real material properties and beam bending theory, to simulate the deformation of blueberry canes under loading. To validate the model, we simulate the canes in MuJoCo and compare their behavior with real-world data collected from probing canes at a commercial farm with a custom testbed. We perform sensitivity analysis on several key modeling variables and show that this approach is highly sensitive to the plant diameter calculations and a priori flexural modulus estimation, which is dependent on season and blueberry variety. We also share our dataset of live blueberry cane deformation, including RGB-D images and measured forces and displacements.

0.20

Force/Torque-Based Kinematic Adaptation for Robotic Manipulation Tasks

cs.RO ·2026-08-21 ·Carl Glen Henshaw
hot direction similarity 0.51
Abstract · 29 pages including appendices, 3 figures

Contact-rich robotic manipulation requires an accurate model of the kinematic relationship between a robot's joints and the task features it senses. This relationship is rarely known exactly: it changes with each tool the robot picks up and shifts, sometimes almost instantaneously, as contact modes change --- especially for multi-fingered hands that make and break contact at points that are not exactly prescribed, as in full-hand grasping. This paper develops an adaptive scheme that estimates that relationship online, using only joint-angle sensing and a wrist-mounted force/torque sensor, with no exteroceptive measurement of the tool tip. We derive a provably stable kinematic update law that identifies the kinematics of an unknown tool from force/torque feedback alone, and prove stability of both the rigid case and the case with a compliance controller as an inner loop. We show that identification is confined to the directions the motion excites --- so that, for example, a tool's length is unobservable under a rigid insertion push, while a compliant loop's passive yielding partially excites it; and that with a second-order admittance the compliant certificate holds unconditionally in continuous time. We also pose the combined control and estimation problem as a Quadratic Program (QP): the formulation yields the prediction term of the update law exactly but, instructively, cannot reproduce the tracking adaptation term. We validate the scheme in simulation on a peg-in-hole insertion. This work is the first step in a research program aimed at factoring manipulation learning into a task policy which can be learned in isolation of the robot, for instance by reinforcement learning, and an adaptive kinematic component that adapts online to the particular robot, hand, or tool in use.

0.29

Adapting Rigid-Body Dynamics Derivatives for Constraint Embedding Closed-Chain Models

cs.RO ·2026-09-17 ·Daniel J. Volpi, Patrick M. Wensing
top venue similarity 0.50
Abstract · 8 pages, 6 figures

This paper extends an existing algorithm for the first-order derivatives of rigid-body dynamics to the case of closed-chain kinematic systems modeled using constraint embed- ding. Many standard dynamics algorithms apply to both open- chain and constraint-embedded models, but existing efficient derivative methods assume joint velocity effects are locally config- uration invariant. We remove this assumption and derive adapted algorithms that extend dynamics derivatives to more general joint types, including those arising in constraint-embedded closed- chain models. Our results compare conventional pin-joint robot models with more complete actuation models that capture local closed chains. We show that the additional terms introduced by these generalizations have low computational impact when mod- eling actuation kinematics alone, but can incur higher cost when additional rigid bodies, such as motor rotors, are included in the actuation chain, or when considering non-local loops. Overall, these results enable more accurate dynamics computations for constraint-embedded actuation submechanisms to be adopted in model-predictive control and differentiable simulation.

0.60

Inertial Steering and Motion Prediction of Tracked Vehicles on Low-Adherence Surfaces

cs.RO eess.SY ·2026-10-28 ·Mathis Turgeon-Roy, Mohamed Ounally, Veronica Vannini, Olivier Roy, François Pomerleau
similarity 0.50
Abstract

Tracked vehicles are widely used in off-road applications, but their conventional motion models often rely on no-slip assumptions that become inaccurate on low-adherence surfaces. Rather than treating inertial effects arising from slip as a disturbance to be minimized, this work investigates how inertial effects arising from a moving mass can be deliberately exploited for steering on low-friction surfaces. A dynamic model for an articulated tracked vehicle with a passive trailer is developed, allowing inertial effects from trailer motion to be captured. The approach is experimentally evaluated on ice, where our dynamic model outperforms the kinematic baseline. We also propose a mixed dynamic-kinematic model to adapt predictions to both surface and situation by exploiting predictions from both methods. Finally, we demonstrate inertial steering on a mono-track vehicle without a conventional steering mechanism, showing that controlled movements of an internal mass can generate turning motion on ice. The resulting behavior can be predicted using the proposed dynamic model by representing the internal mass as a frictionless trailer, revealing the analogous dynamics between the two configurations. These results demonstrate the feasibility of inertial steering as an alternative steering mechanism for tracked vehicles operating in low-adherence environments.

0.21

Control Architecture for Safe Grasping of Fragile Objects Using a Coarse Position-Controlled Gripper

cs.RO ·2026-09-11 ·Marko Pavlic, Moritz Geier, Timo Markert, Darius Burschka
published similarity 0.50
Abstract · Accepted for IEEE IROS 2026 publication

Robots are increasingly used in unstructured environments. The need for them to safely grasp unknown objects without damaging them becomes crucial. Humans achieve this by sensing and quickly responding by adjusting their grasping force. Similarly, effective grasp acquisition in robots requires compliant interaction strategies that can adapt to uncertain object properties and adjust to any instabilities during manipulation. We present a geometry-aware force/torque-based contact estimation method for a coarse position-controlled gripper, combined with an adaptive admittance controller for safe grasp acquisition. The desired contact forces are estimated online to keep stable contact with objects of unknown properties. This enables compliant and stable grasps while avoiding excessive forces. Experiments with objects of different sizes, shapes, stiffnesses, and weights show that the proposed algorithm not only prevents slippage but also applies minimal force to safely grasp an object without causing excessive deformation.

0.28

CW-WAM: A Structured Contact-Wrench World Action Model for Force-Sensitive Manipulation

cs.RO ·2026-10-21 ·Houzhu Ding, Xinda Qi, Luqi Wang, Ming Yang
similarity 0.50
Abstract · Project website: https://cw-wam-project.github.io/

Force-sensitive manipulation requires contact and load information that is not provided explicitly by visual observations. We present CW-WAM, a world action model that jointly predicts video, motion, and contact wrench. Inspired by hybrid motion-force control, it contains a unified interaction module that treats both motion and contact wrench as modeling targets and predicts time-aligned motion-wrench chunks as control references. A pair-causal attention mechanism structures the motion-wrench dependencies, while a long fixed-length wrench memory retains past interaction information. The predicted wrench chunk acts as a force reference for a 20-Hz outer-loop admittance controller within a slow-fast control system that maintains force feedback and smooth motion between model queries. CW-WAM improves contact prediction and increases the insertion success rate from 25% to 70% for square pegs with 1-mm clearance per side and from 40% to 95% for power adapters, compared with WAM without wrench input. It also improves lifting-height accuracy across different loads. Our framework with an admittance controller reduces force-reference RMSE from 4.8 to 2.7 N for peg insertion and from 2.0 to 1.3 N for wiping, respectively, with smaller force fluctuations during successful execution. Project website: https://cw-wam-project.github.io/

0.16

Conceptual full-vehicle modeling of a modular all-wheel-drive robotic ADS test platform as a foundation for a digital twin architecture

cs.RO ·2026-11-18 ·Felix Florian Schwald, Martin Meiners, Michael Viehof, Erik Hultman, Edwin Kamau
similarity 0.49
Abstract · 9 pages, 10 figures. Supplementary project files are available at https://git-ce.rwth-aachen.de/asil-lab-cologne/03_publications/02_pixkitcm…

This paper presents the development of an initial full-vehicle simulation model of the PixKit modular electric test platform in IPG CarMaker. The objective is to create a physics-based and extendable model structure that can serve as a low-level foundation for future digital twin applications. The reference vehicle is a skateboard chassis combining unconventional vehicle characteristics such as four independent wheel-hub motors and rear axle steering capable of high steering angles. Since complete measurement data of the vehicle is not yet available, the model parameterization is based on a combination of manufacturer documentation, derived values and engineering assumptions. The modeling approach focuses on the system-level integration of the main vehicle subsystems rather than on a fully validated representation. The resulting model was assessed through basic driving scenarios with different steering inputs and configurations. The simulations showed stable model behavior and physically plausible interaction between the subsystems. The all-wheel-drive configuration produced symmetric wheel responses in longitudinal driving, while counter-phase rear axle steering increased the yaw response and reduced the simulated turning circle diameter compared with front axle steering only. The circular driving scenario further indicated bounded roll and slip behavior. Overall, the implemented CarMaker model provides a traceable and functional simulation basis for the PixKit vehicle. It can support future model refinement, calibration with real vehicle data and development with the goal of creating a validated digital twin architecture.

0.40