CS Paper Radar

Identification of the Steering and Speed Systems of a Four-Wheel-Steering Tractor for Optimal Control

Riikka Soitinaho, Timo Oksanen

eess.SY ·submitted 2026-09-04 05:02 UTC · v1

Abstract

Model-based control design requires sufficiently accurate model of the system-to-be-controlled. This paper addresses the system identification of steering and speed control of a four-wheel-steering agricultural tractor for the purpose of developing path tracking control. To this end, we investigate the steering and speed control systems of the tractor. These are complex systems with digital, mechatronic, and hydraulic components challenging to model based on first principles. We take a data-driven approach to estimating the system models. The resulting model combines the kinematic model of the vehicle, actuators modelled as first-order systems, and estimated values for time constants and transport delays.

Closest papers

Nearest neighbours by meaning across the whole index.

Multi-Reference Path Tracking Control for an Agricultural Tractor with Nonlinear Model Predictive Control

cs.RO ·2026-09-04 ·Marcel Moll, Timo Oksanen
similarity 0.63
Abstract

Guiding a tractor along a predefined reference path is a key component of precision agriculture. This study develops a path tracking controller based on Nonlinear Model Predictive Control, which incorporates multiple segments of a piecewise-linear reference path directly into the objective function. In addition, methods for selecting viable reference segments from the full path are presented. The control system is evaluated during a field test with a tractor controlled via the Tractor Implement Management steering interface. The NMPC solver converged on average after 3.45 ms and tracked the curved reference path with a mean absolute cross-track error of 6.1 cm.

0.28

A Novel Path-Tracking Algorithm for Automated Tractor-Trailer Forward and Backward Maneuvers

cs.RO eess.SY ·2026-09-18 ·Alexandre Lombard, Florent Perronnet, Théo Rigal, Nicolas Gaud, Abdeljalil Abbas-Turki
similarity 0.63
Abstract

Fully autonomous tractor-trailer systems are increasingly deployed in logistics, agriculture, and industrial environments, where precise and robust path-tracking capabilities are essential. However, the articulation between the tractor and the trailer introduces additional nonlinearities and significantly complicates lateral and longitudinal control, particularly during reversing maneuvers. This paper introduces a novel path-tracking algorithm specifically designed for articulated vehicles with a single trailer. The proposed method combines a lateral control law applied at the trailer level with a short-horizon predictive adjustment of the tractor steering angle, ensuring stable convergence toward the desired path in both forward and backward motion. The approach is geometry-based and requires no per-vehicle calibration or training. Simulation studies in a high-fidelity physics simulator show steady-state or final lateral errors of $0.02$--$0.05$~m on straight-line, circular, and reverse docking trajectories, which is of the same order of magnitude as, or lower than, the errors reported in the literature. Real-world experiments on a small-scale tractor--trailer robot, with the whole controller running on a low-cost microcontroller, further confirm the feasibility of the approach, with lateral errors below 13~mm during repeated reverse docking maneuvers despite a pose detection latency of about 200~ms.

0.10

High-Speed Forward and Reverse Tractor-Trailer Driving with Learned Vehicle Dynamics

cs.RO eess.SY ·2026-11-15 ·Aaron Chen, David Shen, Taekyung Kim, Kaleb Ben Naveed, Dimitra Panagou
code/data similarity 0.56
Abstract · The first three authors contributed equally to this work. Project page: https://ds12a.github.io/drift-with-trailer/

Tractor-trailer systems are difficult to control, especially unstable during reverse motion, and their dynamics depend on difficult-to-measure factors, including road friction and suspension coefficients. We introduce a learned dynamics model for tractor-trailer control and compare it with a reduced-order dynamics model with Fiala tire forces as an analytic baseline. Specifically, we compare a model predictive path integral (MPPI) controller that uses the learned dynamics model to an MPPI controller that uses the analytic model, as well as to three additional baseline controllers. In the main closed-loop tracking experiments across four simulated environments, MPPI with learned dynamics achieves mean speeds closer to the target magnitudes and lower root-mean-square (RMS) hitch angles than MPPI with the analytic model at every tested setpoint, with higher completion rates in seven of eight reverse configurations.

0.17

Model predictive traction control system based on the Koopman operator

eess.SY ·2026-08-26 ·Josip Kir Hromatko, Šandor Ileš
publishedcode/data similarity 0.54
Abstract · 6 pages, 4 figures; associated code available at https://github.com/PVDC-project/pvdc-kmpc-traction-control

Due to their importance, traction control and anti-lock braking systems have become standard equipment in modern vehicles. However, accurate models of tire dynamics are often difficult to obtain and usually include nonlinearities, making their use in control systems challenging. This paper describes a traction control system based on model predictive control and Koopman operator theory, which aims to approximate nonlinear systems with linear ones through a state space transformation. A linear model predictive controller based on the Koopman predictor is compared to a standard nonlinear model predictive controller. Experiments in a high-fidelity vehicle dynamics simulation environment show a comparable reference tracking performance of the two controllers, with a reduced execution time for the proposed Koopman operator-based algorithm, both on a standard PC and embedded hardware.

0.78

Constrained Optimization-Based Yaw-Rate Reference Map Generation for Active Rear Steering Control of Four-Wheel Steering Vehicles

eess.SY ·2026-09-19 ·Myeongseok Ryu, Donghyun Hwang, Youngsik Yoon, Kyunghwan Choi
published similarity 0.54
Abstract · This work has been submitted and accepted to International Conference on Control, Automation and Systems (ICCAS) 2026

The effectiveness of active rear steering (ARS) control for four-wheel steering (4WS) vehicles is widely recognized in the automotive industry. At low speeds, ARS control can enhance maneuverability by steering the rear wheels in the opposite direction to the front wheels, reducing the turning radius. In contrast, at high speeds, ARS control can improve stability by steering the rear wheels in the same direction as the front wheels, preventing oversteer behavior. However, the performance of ARS control is often limited by the reference model used to generate the desired yaw rate, which is typically derived from a steady state of front-wheel steering (FWS) vehicle model. In this paper, we conduct a numerical analysis to construct an optimal yaw rate reference map for ARS control by formulating a constrained optimization problem. In the optimization problem, constraints are imposed to ensure that the vehicle operates within safe limits at steady state. Numerical simulations demonstrate the effectiveness of the proposed method in providing an optimal yaw rate reference map for ARS control.

0.32

System Identification of Admittance Models for Large Real-World Objects

cs.RO ·2026-08-30 ·Nathan I. Baum, Nathaniel G. Luttmer, Mark A. Minor
similarity 0.54
Abstract · 8 pages, 7 figures,1 table

Simulation of admittance-type models requires physically consistent dynamic models that are rarely available for off-the-shelf, everyday objects, limiting the fidelity of haptic interfaces that rely on such simulations. This paper presents the first complete workflow for producing physically consistent models of large real-world objects with various constraints and mechanisms, guaranteeing physical consistency of inertia and friction parameters. The workflow separates each object and identifies the handle and body in two stages, requiring no torque sensors at hinges, axles, or other constrained joints. Models are produced for a heavy, closer-actuated door and a wheelbarrow, representing objects of differing constraint types and model complexity. The door is modeled using four-bar linkage kinematics and a fluid dynamics-based lumped parameter model including opening, backcheck, swing, and latch zones. The wheelbarrow is modeled as a rigid body with a spherical wheel and no slip during rolling. Handle estimation RMS errors were below 0.64 N and 0.042 Nm across both objects. Door body estimation had RMS error of 2.19 Nm and wheelbarrow body estimation had RMS error of 6.77 Nm.

0.29

Observability Analysis and Online Calibration of Visual-Inertial-Wheel Odometry for 4WIS4WID Mobile Robots

cs.RO ·2026-09-29 ·Branimir Ćaran, Vladimir Milić, Bojan Šekoranja, Bojan Jerbić
similarity 0.53
Abstract · This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may…

In this paper, we present a visual-inertial-wheel odometry (VIWO) framework with online calibration for four-wheel independently steered and driven (4WIS4WID) mobile robots. We derive a 2D odometry model directly from the four driving velocities and steering angles, using both the longitudinal rolling constraints and the lateral no-slip constraints of all wheels. A preintegration model and analytical Jacobians are developed for efficient filtering and calibration. An observability analysis of the linearized VIWO system shows that a drive-only model makes all steering offsets unobservable, whereas the proposed redundant model restores their observability. The analysis also identifies four standard VINS unobservable directions and three additional directions associated with the arbitrary placement of the odometry reference frame. Furthermore, we characterize several degenerate motions, including zero yaw rate, constant steering, and a non-rolling wheel, and derive the corresponding excitation conditions for the thirteen wheel intrinsics that remain after fixing the odometry frame reference. The performance of the proposed system has been demonstrated in both simulation and real-world experiments on a 4WIS4WID mobile robot.

0.21

Data-driven design of steady-state feedforward inputs for nonlinear systems under partial measurement

eess.SY ·2026-09-08 ·Sathya Aswath Govind Raju, Berk Altiner, Zongxuan Sun, Arunava Banerjee, Rajasree Sarkar +2 more
similarity 0.52
Abstract

Designing trajectory tracking controllers for nonlinear systems remains a significant challenge, traditionally requiring precise mathematical models and complex analytical derivations. While the Internal Model Principle (IMP) provides a robust theoretical foundation for such problems, its application is often hindered by model uncertainty and the inherent complexity of nonlinear controller synthesis. This work proposes a practical data-driven control framework that bypasses the need for an explicit first-principles model by utilizing raw input-output data. By integrating fundamental results from IMP theory with nonlinear system analysis, the proposed approach improves design tractability. The framework's efficacy is validated through numerical simulations on two distinct nonlinear platforms: a mechanical load with a nonlinear friction term and an electrohydraulic actuator system.

0.27