CS Paper Radar

Vertical Assessment of RF-EMF Exposure in a Building Adjacent to a Multi-Operator Shared Base Station

Ricardo Q. de F. H. Silva, Marcio E. C. Rodrigues, Fred S. R. Pinheiro, Gutembergue S. da Silva, Halysson B. Mendonça, Vicente A. de Sousa

cs.NI ·submitted 2026-09-11 12:38 UTC · v1
published

Abstract

This paper extends a previously published proposed approach for estimating worst-case exposure scenarios in buildings using publicly available Base Station (BS) parameters, applying it to a critical case involving a multi-operator shared site. Radiofrequency Electromagnetic Fields (RF-EMF) exposure was assessed on every floor of a 20-story building facing the site, revealing significantly higher levels near the center of the antennas' estimated vertical zone of interest, with a peak of 31.86 V/m, 23.95 times higher than the street-level peak value. However, due to uncertainties in the input parameters, measurements across all locations within the zone of interest are required to accurately identify the floor of maximum exposure. The results demonstrate the usefulness of the proposed estimation approach and highlight the need for improved methods that consider BS antenna configurations and current technical information to ensure accurate assessments of exposure to RF-EMF.

Journal ref
Journal of Communication and Information Systems 2026, 41(1), 77-82
DOI
10.14209/jcis.2026.8

Closest papers

Nearest neighbours by meaning across the whole index.

Human Exposure to Non-Ionizing Radiation from Indoor Distributed Antenna System: Shopping Mall Measurement Analysis

cs.NI ·2026-09-16 ·Júlia da L. A. Silva, Vicente A. de Sousa,, Marcio E. C. Rodrigues, Fred Sizenando Rossiter Pinheiro, Gutembergue Soares da Silva +6 more
publishedhighly cited similarity 0.65
Abstract

It is crucial to monitor the levels of Non-Ionizing Radiation (NIR) to which the general population may be exposed and compare them to the limits defined in the current standards, in view of the rapid rise of communication services and the prospects of a connected society. A high number of people visits shopping malls and since these locations usually have several indoor antennas close to the public, it is therefore a kind of place that must be evaluated. Thus, this work presents measurements of the electric field in a shopping mall located in Natal, Brazil. We proposed a set of six measurement points, following two criteria: places with great the flow of people and the presence of one or more Distributed Antenna System (DAS), co-sited or not with WiFi access points. Results are presented and discussed in terms of the distance to DAS (conditions: near and far) and flow density of people in the mall (scenarios: low and high number of people). The highest peaks of electric field measured were 1.96 and 3.26 V/m, respectively corresponding to 5% and 8% of the limits defined by the International Commission on Non-Ionizing Radiation Protection (ICNIRP) and the Brazilian National Telecommunication Agency (ANATEL).

0.58

UrbanEMF: City-Scale EMF Mapping over a Continuous Urban Area with Real-World Base-Station Deployment

eess.SP ·2026-10-01 ·Shuangning Li, Chenxin Luo, Shanshan Wang, Yarui Zhang, Paul Lagouanelle +1 more
benchmarkdatasetcode/data similarity 0.60
Abstract

Electromagnetic Fields (EMF) mapping is essential for wireless propagation modeling and are fundamental to a wide range of applications, including spectrum awareness, network planning, and integrated sensing and communication (ISAC). However, existing datasets are often limited to spatially separated 2D scenes without real base station (BS) information. To address this gap, we present UrbanEMF, a city-scale EMF mapping dataset constructed from real world urban geometry and physical BS deployments using ray tracing. Unlike conventional single scene-based datasets, UrbanEMF preserves continuous city-scale urban coverage and realistic transmitter location information. It further extends traditional 2D maps by incorporating multiple receiver heights. In addition, both aggregated received signal strength (RSS) maps and path loss maps are provided to characterize complementary aspects of the radio environment. This work provides a realistic and flexible benchmark for developing and evaluating learning-based methods in large-scale urban wireless environments. The code for this work is available at: https://github.com/lemonstudy/UrbanEMF

0.53

Intelligent Reflecting Surface Deployment for Low-Altitude Coverage: Illumination Geometry, Directional Characteristics, and Optimization

cs.IT ·2026-08-31 ·Guoying Zhang, Qingqing Wu, Ailing Zheng, Xingxiang Peng, Wen Chen +1 more
theory similarity 0.57
Abstract · Submitted to an IEEE journal for possible publication

Terrestrial base stations (BSs) are typically configured with fixed downtilt to serve ground users, resulting in weak illumination of low-altitude airspace even under line-of-sight (LoS) propagation. In this paper, we establish a channel model that incorporates BS and intelligent reflecting surface (IRS) radiation patterns for three-dimensional (3D) low-altitude coverage while preserving the existing BS configuration. We formulate a budget-constrained IRS deployment problem that jointly determines candidate-site selection, IRS orientations, and phase shifts to maximize the worst-case signal-to-noise ratio (SNR) over the 3D low-altitude airspace. The selected sites and optimized IRS parameters remain fixed after deployment, yielding a quasi-static IRS configuration. We characterize the illumination geometry between the fixed-downtilt BS and rooftop candidates by deriving the nonnegative installation-height range satisfying the BS main-lobe condition. The separation between the mapped main-lobe height boundaries grows linearly with horizontal BS-to-site distance and decreases inversely with the number of BS antennas. We further derive an analytical lower bound on the regional worst-case normalized array gain achievable through IRS phase design over served directions with different direction spans. The resulting sufficient direction span decreases inversely with the square root of the number of IRS elements when the same worst-case normalized gain guarantee is maintained. We develop a mixed-integer alternating optimization (AO) algorithm to solve the resulting problem. Simulation results validate the analytical characterizations and show that the proposed scheme achieves higher worst-case SNR than benchmarks across different deployment budgets.

0.19

Multi-Band Indoor MIMO Channel Measurements Across Sub-6 GHz, Mid-Band and mmWave: Comparing 2.55 GHz, 12.75 GHz and 25.5 GHz

eess.SP ·2026-11-11 ·Faruk Pasic, Florian Kiss, Florian Asperger, Diego Dupleich, Stefan Schwarz +1 more
published similarity 0.56
Abstract · Submitted to the 21th European Conference on Antennas and Propagation (EuCAP), 2027

Future wireless systems for indoor applications are expected to extend their operating frequencies from sub-6 GHz to mid-band and millimeter wave (mmWave) frequencies to support higher data rates. To characterize the frequency-dependent propagation behavior across these bands, multi-band channel measurements are essential. In this work, we conduct double-directional multiple-input multiple-output (MIMO) channel measurements in an indoor environment to enable a consistent comparison across three frequency bands. Measurements are performed using a 16x16 MIMO configuration at center frequencies of 2.55 GHz, 12.75 GHz and 25.5 GHz, covering both line-of-sight (LOS) and obstructed line-of-sight (OLOS) conditions. The measured channels are processed using the space-alternating generalized expectation maximization (SAGE) algorithm to extract multipath parameters, which are subsequently used to characterize the angular power distributions across the three frequency bands. The results show substantial angular-domain similarity across all three bands in both LOS and OLOS conditions, while also highlighting frequency-dependent variations.

0.31

Device-Centric Cooperative Floor-Level Estimation under Sparse Anchor Deployment for Construction-Site Applications

eess.SP ·2026-11-17 ·Jiaxu Liang, Zhuoran Li, Osamu Muta, Haruto Morokuma, Naohiro Ikeda +1 more
similarity 0.52
Abstract

For construction-site applications in multi-story buildings, accurate floor-level estimation is important for tracking workers, equipment, and Internet of Things (IoT) devices. In buildings under construction, communication infrastructure and power-supply facilities are often limited and the indoor environment changes as construction progresses, making localization systems that rely on dense wireless infrastructure or fingerprint databases difficult to deploy and maintain. Low-power wide-area (LPWA) communication can provide wide-area coverage with a small number of temporarily deployed access points (APs), but under sparse AP deployment, AP-to-terminal observations alone may provide insufficient floor-related information for reliable floor-level estimation. To address this problem, this paper develops a device-centric cooperative floor-level estimation method that exploits inter-terminal observations as relative floor-difference information to complement AP-side information. For practical application with limited measurement data, AP-to-terminal observations are represented by an upper/lower-AP RSS contrast, while inter-terminal observations are statistically modeled according to floor-difference classes. The resulting AP-side and pairwise scores are combined in a weighted floor-label objective and approximately optimized using dual-order sequential iterated conditional modes (ICM). Ray-tracing simulations and LoRa measurement experiments demonstrate the effectiveness of the proposed method under different AP deployments and terminal-selection limits.

0.26

Non-Ionizing Radiation Analysis in Close Proximity to Antenna Tower: A Case Study in Northeast Brazil

cs.NI ·2026-09-28 ·André B. F. Diniz, Vicente A. Souza, Marcio E. C. Rodrigues, Halysson B. Mendonça, Gutembregue S. Silva +1 more
publishedhighly cited similarity 0.52
Abstract

While the amount of telecommunications services grows rapidly in the whole world, humans get potentially more exposed to Non-Ionizing Radiation (NIR) from a number of different sources. This paper has a number of goals, including monitoring radiation levels in an everyday situation, an investigation of how national and international regulations organs address NIR levels and a demonstration of scientific production trends regarding this topic. The work also presents a bibliometric study about the main scientific productions and trends related to NIR measurements, with focus on the field of Telecommunications. Another contribution is a case study in Natal, Brazil, where NIR levels were monitored in four distinct locations over a period of 24 hours each and compared to the current regulations. The result is a quantitative analysis of the amount of radiation that some populations might be exposed to in distinct moments of the day. Measurements were carried out in the proximity of an antenna spot, since it could represent a source of high NIR levels (a worst case of human exposure). This campaign differs from older studies by including a more intense usage of microwaves frequencies due to operating 4G and pre-5G systems in Brazil. Finally, a statistical study involving the measurements is conducted, concluding the analysis of how some population groups might be affected by NIR.

0.52

Adaptive Calibration of RF Digital Twins via Budget-Constrained Radio Measurement Selection

cs.NI eess.SP ·2026-10-26 ·Yalin E. Sagduyu, Tugba Erpek, Hossein Jafari
published similarity 0.52
Abstract

Radio-frequency (RF) digital twins (DTs) enable site-specific wireless propagation prediction by explicitly reconstructing the physical environment and modeling electromagnetic interactions. Although physics-based DTs reduce reliance on exhaustive measurements, systematic bias relative to real radio data arises from environmental uncertainty, material inaccuracies, and geometric abstractions. Calibration using field measurements is therefore necessary but costly under limited sampling budgets. This paper studies active RF DT calibration, in which measurement locations are selected sequentially and in an online manner to estimate a calibration offset under strict measurement budget constraints. A physics-based RF DT pipeline is developed, integrating semantic geospatial data from OpenStreetMap, 3D modeling in Blender, and deterministic ray tracing in Sionna to capture dominant building and foliage effects. This RF DT is calibrated using path-loss measurements collected with software-defined radios. Multiple online calibration strategies that select radio measurement locations are compared, including random sampling, rank-structured sampling with balanced coverage, quasi-Monte Carlo ranked selection, progressive structure-aware allocation, and fully adaptive uncertainty-driven sampling with estimator stabilization. Results demonstrate that adaptive and structure-aware schemes significantly improve both mean and worst-case calibration accuracy, particularly in the low-budget regime for radio measurements.

0.33

Realistic Characterization and Modeling of Vehicle-Mounted Antenna Radiation Patterns Based on Large-Scale Full-Vehicle Measurements

eess.SP ·2026-09-29 ·Guotian Ji, Tianhao Wang, Changhao Xi, Guokai Jiang, Jiaxu Feng +2 more
similarity 0.52
Abstract · Under peer-review of the IEEE Journal

Vehicle-mounted antenna radiation patterns can be significantly altered after installation due to interactions with the vehicle body. However, existing studies mainly focus on simulations or isolated antenna characterization, while large-scale experimental investigations remain limited. This paper presents a comprehensive experimental analysis of vehicle-mounted antenna radiation patterns based on full-vehicle spherical near-field measurements. A large-scale dataset covering ten commercial vehicle platforms, multiple antenna mounting locations, and various wireless functions, including 4G, 5G, V2X, and GNSS, is established under a unified measurement framework. Based on the measured results, representative case studies and statistical characterization are performed to investigate the impacts of vehicle installation on antenna radiation behavior. The results reveal substantial variations across mounting locations and wireless functions, highlighting the strong influence of vehicle integration on realistic antenna performance. Furthermore, a novel statistical model is proposed to generate realistic vehicle-mounted antenna patterns using a small set of physically interpretable parameters. The obtained dataset, characterization results, and modeling approach provide a foundation for realistic antenna evaluation and wireless system simulations in vehicular communication applications.

0.25