CS Paper Radar

Adaptive Calibration of RF Digital Twins via Budget-Constrained Radio Measurement Selection

Yalin E. Sagduyu, Tugba Erpek, Hossein Jafari

cs.NI eess.SP ·submitted 2026-10-26 23:40 UTC · v1
published

Abstract

Radio-frequency (RF) digital twins (DTs) enable site-specific wireless propagation prediction by explicitly reconstructing the physical environment and modeling electromagnetic interactions. Although physics-based DTs reduce reliance on exhaustive measurements, systematic bias relative to real radio data arises from environmental uncertainty, material inaccuracies, and geometric abstractions. Calibration using field measurements is therefore necessary but costly under limited sampling budgets. This paper studies active RF DT calibration, in which measurement locations are selected sequentially and in an online manner to estimate a calibration offset under strict measurement budget constraints. A physics-based RF DT pipeline is developed, integrating semantic geospatial data from OpenStreetMap, 3D modeling in Blender, and deterministic ray tracing in Sionna to capture dominant building and foliage effects. This RF DT is calibrated using path-loss measurements collected with software-defined radios. Multiple online calibration strategies that select radio measurement locations are compared, including random sampling, rank-structured sampling with balanced coverage, quasi-Monte Carlo ranked selection, progressive structure-aware allocation, and fully adaptive uncertainty-driven sampling with estimator stabilization. Results demonstrate that adaptive and structure-aware schemes significantly improve both mean and worst-case calibration accuracy, particularly in the low-budget regime for radio measurements.

Closest papers

Nearest neighbours by meaning across the whole index.

TRACE: Learning to Self-Calibrate Wireless Digital Twins from ISAC Measurements

cs.AI eess.SP ·2026-09-26 ·Saad Masrur, Saeed R. Khosravirad, Ismail Guvenc
similarity 0.74
Abstract · Under Review

Wireless digital twins (DTs) rely on 3D environment models to predict radio propagation and support wireless-network decisions, yet these models are often initialized from imperfect 3D maps. Errors in building position, height, footprint, and orientation can therefore cause a high-fidelity propagation engine to simulate the wrong physical environment. In this paper, we study how a deployed wireless network can repair an existing DT using its own radio frequency (RF) measurements. In particular, we introduce Twin Residual Alignment and Calibration Engine (TRACE), a physics-grounded learning-based self-calibration framework that treats twin maintenance as residual alignment between the physical world and the current DT. Using the same sensing configuration as the physical measurements, TRACE ray-traces the current DT, coherently backprojects the measured and simulated RF onto a common world grid, and extracts the same local region around each building's current DT position. A multi-view corrector then fuses evidence across sensing nodes and neighboring buildings to predict a gated six-parameter correction per building, without relying on absolute layout or sensor ordering, and supports iterative correction through re-rendering. On 5,400 held-out samples from unseen simulated scenes at 28 GHz, TRACE reduces 3D position RMSE from 2.202 m to 0.302 m and yaw RMSE from 4.978° to 0.894°, outperforming ViT and U-Net baselines under changes in layout, building count, sensing-node count, and SNR. On measured 28 GHz RF data from the NIST outdoor courtyard, a model trained only on synthetic RF reduces mean planar wall-position error from 1.00 m to 7.8 cm, without measured-data fine-tuning or geometric labels. These results show that the discrepancy between measured and twin-rendered RF can serve as a learning signal for repairing a wireless DT.

0.12

KODAMA: Multimodal Digital Twin Reconstruction for Urban RF Propagation Modelling

cs.CV ·2026-09-07 ·Maximiliano Wardle, A. Ryo Koblitz
similarity 0.73
Abstract

3D reconstruction typically strives for geometric fidelity or visual plausibility. Radio frequency digital twins (RFDT) are instead judged by whether communication channels behave in them as they do in the real world. RFDTs promise site-specific channel prediction but current practice forces a choice between coarse automated scenes and hand-built, measurement-calibrated models that take weeks to construct per-site. We present KODAMA, an automated pipeline that reconstructs ray tracing-ready RFDTs at city scale from off-the-shelf geospatial data alone: aerial imagery, LiDAR, and photogrammetry yield terrain and watertight building meshes, while exposure-weighted multi-view fusion of street-level imagery recovers façade relief, electromagnetic materials, and clutter---all without site visits or calibration. Across three sites spanning 3.6 to 28 GHz, KODAMA's uncalibrated predictions achieve single-digit RMSE, reducing point-to-point error by up to 5.35 dB over automated baselines and coming within 0.22 dB of a measurement-calibrated, hand-built RFDT.

0.10

HalifaxDT: A Wireless Digital Twin from Open Geospatial Data

cs.NI ·2026-09-05 ·Alexis Delplace, Xinyi Li, Samer Lahoud, Nur Zincir-Heywood
similarity 0.71
Abstract

Wireless digital twins can support site-specific analysis, planning, and experimentation for future wireless networks. However, constructing them at city scale remains challenging when accurate 3D city models are unavailable. This paper presents HalifaxDT, a wireless digital twin of the Halifax Peninsula in Nova Scotia, Canada, constructed from heterogeneous open geospatial and spectrum data. HalifaxDT combines building footprints, LiDAR elevation products, building metadata, and spectrum licensing records through a workflow that reconciles multiple sources of building-height information while preserving the provenance of geometry decisions. The resulting terrain, buildings, and gateway metadata are integrated into Sionna RT for wireless simulation. We evaluate HalifaxDT through two use cases. The first compares its coverage predictions with a reference derived from field measurements and with an analytical baseline. The second uses the digital twin to predict the received signal under normal operating conditions and detect interference. The coverage results show that HalifaxDT better preserves the spatial structure of the measured radio map than the analytical baseline. The interference study shows that deviations from the predicted reference can reveal interference that is difficult to detect from received power alone. We also identify current fidelity limitations, including simplified material representation, missing vegetation, and the need for broader RF calibration and synchronization with live measurements.

0.33

Site-specific Channel Modeling Based on Remote-Sensing Maps for 6G Space--Air--Ground Digital Twins

eess.SP ·2026-08-31 ·Peijie Liu, Pan Tang, Jianhua Zhang, Lei Tian, Bin Ao +2 more
similarity 0.70
Abstract · 17 pages, 23 figures, 4 tables

Site-specific channel models are essential for wireless digital twins of 6G space--air--ground communication systems. However, 3D maps are difficult to obtain over wide areas, which limits large-area site-specific channel modeling. To address this issue, this paper proposes a remote-sensing-based augmented ray-tracing channel modeling framework. The framework comprises a deterministic RT branch, a measurement-statistical branch, and an RT augmentation branch. To overcome the difficulty of acquiring large-area 3D maps, the deterministic RT branch reconstructs a 3D RT scene from satellite remote-sensing imagery and calibrates its electromagnetic material parameters using measured path loss. To provide the statistical parameters required for RT augmentation, the measurement-statistical branch establishes the marginal distributions and interparameter dependence models of the channel parameters. Specifically, a wideband UAV channel measurement campaign is conducted at 4.60 GHz, and a proposed multipath estimation method estimates the complex amplitudes, delays, and Doppler shifts of the measured multipath. To bridge the gap between RT predictions and measurements, the RT augmentation branch organizes the RT multipath into LoS, LoS-tail, and NLoS components, generates additional short-delay LoS-tail paths, and reallocates the component and path powers according to the measurement-derived statistics while preserving the total RT received power. The validation results show that the proposed framework reduces the path loss RMSE from 5.45 to 4.35 dB and, relative to calibrated RT, decreases the RMS delay spread and normalized Doppler spread RMSEs by 53.03 and 26.48, respectively. The proposed framework provides a site-specific channel modeling approach for 6G space--air--ground digital-twin studies.

0.26

Efficient and Accurate Surrogate-Assisted Electromagnetic Parameter Calibration for 6G Digital Twin Channels

eess.SP ·2026-08-13 ·Xiaofan Zou, Pan Tang, Peijie Liu, Changyou Tai
similarity 0.67
Abstract

High-fidelity ray-tracing (RT) channel reconstruction is a fundamental step toward building digital twins for the era of 6G wireless communications. However, precise calibration of complex electromagnetic material parameters remains a dual challenge characterized by massive computational overhead and strict accuracy requirements. To overcome this bottleneck, we propose a Surrogate-assisted Grey Wolf Optimizer with Individual Memory (SGWO-IM) algorithm that simultaneously improves computational efficiency and calibration accuracy. In terms of computational efficiency, an online surrogate model is seamlessly embedded into the evaluation workflow for candidate pre-screening, substantially reducing the reliance on highly time-consuming real RT simulations. Regarding calibration accuracy, adaptive convergence and individual memory strategies are incorporated to optimize the global parameter search path, effectively enhancing the consistency between the reconstructed channel and measured data. Validated against measured channel data from a high-density urban scenario, the proposed algorithm requires only 225 real RT simulation calls compared to the 600 calls needed by the standard Grey Wolf Optimizer (GWO), cutting computational overhead by 62.5%. Concurrently, the final Root Mean Square Error (RMSE) is substantially reduced from the 3.65 dB of GWO to 2.97 dB. The results demonstrate that the SGWO-IM algorithm achieves significant advancements in both efficiency and precision, providing a solution that effectively balances efficiency and accuracy for electromagnetic environment reconstruction.

0.04

Agentic Wireless Digital Twin Construction and Calibration Using Real-World Measurements

cs.IT ·2026-10-01 ·Fan-Hao Lin, Kun-Li Shih, Chu-Hsiang Huang, Hui Chen, Chao-Kai Wen +1 more
similarity 0.64
Abstract · 6 pages, 6 figures, 1 table. Submitted to IEEE conference

Wireless digital twins (WDTs) are promising enablers for developing and evaluating AI-native radio access networks, yet constructing a high-fidelity WDT typically requires substantial manual effort to integrate heterogeneous information and infer unknown propagation-related parameters. This paper proposes Agentic WDT (AWDT), an end-to-end agentic framework for autonomous WDT construction and calibration using readily available environmental information and measurements readily obtainable from commercial smartphones. AWDT comprises three agents: EnvAgent constructs the propagation environment, OpAgent infers BS and sector configurations, and MatAgent calibrates radio material properties. The agents iteratively refine the WDT using discrepancies between LTE/NR reference signal received power (RSRP) measurements and ray-tracing predictions. Real-world experiments show that AWDT reduces the RSRP prediction MAE from 11.46 to 5.25 dB, demonstrating a substantial improvement in ray-tracing fidelity. Evaluation with an independent measurement system further demonstrates cross-device transferability with lightweight device-specific bias adaptation, highlighting the potential of agentic AI for scalable WDT construction and calibration with limited prior knowledge.

0.21

RadioTraj3D: Height-Aware Adaptive Sampling for 3D Radio-Map Reconstruction from Ultra-Sparse Trajectories

eess.SP ·2026-10-30 ·Zixuan Guo, Xiucheng Wang, Wenshuo Chen, Conghao Zhou, Chuan Huang +2 more
similarity 0.63
Abstract

Aerial networks require radio propagation information at unvisited positions and heights to plan routes, select links, and allocate wireless resources. A three-dimensional radio map (3D RM) represents propagation conditions over the service area, enabling these decisions before flight. However, constructing such a map from autonomous aerial vehicle (AAV) measurements is challenging, since radio measurements are available only along the trajectory, whereas the target covers the 3D service volume. Existing methods use fixed AAV trajectories that ignore how building distributions and heights affect electromagnetic propagation, missing the heights most informative for RM reconstruction. To address these issues, we propose RadioTraj3D, which uses building-height information to coordinate measurement selection and layer-wise reconstruction. Building-height variations reveal propagation-sensitive layers that guide height-adaptive sampling. We therefore propose G-METS to select geometry-sensitive heights and allocate an exact budget across edge, corridor, and open regions before channel acquisition. A dual-view reconstructor then integrates local three-dimensional boundaries with full-height context through one bounded coefficient per layer. Simulated outdoor and indoor maps demonstrate state-of-the-art reconstruction across environments and vertical grids. On real-world AAV measurements from the LACN dataset, RadioTraj3D improves peak signal-to-noise ratio by 0.84 dB and reduces normalized mean squared error by 17.5% over Completion AE.

0.32

DeepRT-Cal: Learning to Calibrate Ray-Traced Twin Channel Statistics with Low-Fidelity Environmental Geometry

eess.SP ·2026-11-06 ·Shaoyi Liu, Jianhua Zhang, Li Yu, Yichen Cai, Tao Wu +3 more
similarity 0.60
Abstract · 15 pages, 14 figures, 3 tables

Sixth-generation (6G) wireless systems increasingly rely on digital twin channels (DTCs) to represent and interact with physical radio environments. Ray tracing (RT) is naturally suited to DTC construction because it provides deterministic and physically interpretable channel predictions. However, high-fidelity three-dimensional environment models are expensive to obtain, whereas geometric inaccuracies in low-fidelity models can alter the detected multipath components (MPCs) and consequently distort received-power and delay-domain twin channel statistics. Building on the DeepRT ray-tracing framework, this paper proposes DeepRT-Cal, a geometry-aware cross-fidelity calibration framework that predicts high-fidelity twin channel statistics from low-fidelity geometry and RT features.The network encodes global link descriptors, masked low-fidelity MPC tokens, propagation-corridor geometry, and link-centered environmental objects. During training, detailed geometry is introduced as privileged information with structured masking, while deployment requires only low-fidelity geometry and low-fidelity RT information. A link-conditioned cross-attention module retrieves the environmental context relevant to each Tx--Rx link. The prediction heads estimate high-fidelity twin channel statistics, including total received power, RMS delay spread, mean excess delay, and a normalized power-weighted power-delay profile (PDP). Outdoor evaluation shows that, in an non-line of sight (NLoS) region, the method reduces power MAE from 16.80 to 3.88 dB and RMS delay-spread MAE from 304.89 to 98.19 ns. In a LoS-dominated region, power prediction improves, while RMS delay-spread accuracy remains comparable to direct RT.

0.28