CS Paper Radar

Burst-mode timing recovery based on fourth-power phase detector for passive optical networks

Ji Zhou, Haide Wang, Xiaofeng Zhang, Zhiyang Liu, Miao Yu, Changyuan Yu, Liangchuan Li, Xiangjun Xin

cs.NI ·submitted 2026-09-14 02:32 UTC · v1
publishedunusual

Abstract

Driven by the ever-increasing capacity demands, 50G passive optical network (50G-PON) is ready for practical application. It is highly challenging to realize 50GHz burst-mode analog components; therefore, based on 25GHz burst-mode analog devices, burst-mode digital signal processing (DSP) is introduced to achieve the reception and processing of 50Gb/s on-off keying burst signals. To optimize the power consumption and area of the DSP chip, a one-sample-per-symbol (1-SPS) analog-to-digital converter has been applied in 50G-PON. One of the main challenges is implementing burst-mode timing recovery (BM-TR) for the 1-SPS burst signal in 50G-PON. In this paper, we first propose a BM-TR based on the fourth-power phase detector (4PPD) for 50G-PON. We mathematically verify that 4PPD can directly compute the timing phase offset (TPO) from the 1-SPS signal without using training sequences, allowing for immediate BM-TR initialization within 20 cycles to prevent long convergence times. After the initialization, the feedback loop structure tracks the TPO changes based on the sign of 4PPD, the loop filter, and the numerically controlled oscillator. In conclusion, training-sequence-free 4PPD-based BM-TR achieves low burst overhead via fast convergence and is particularly effective for handling burst signals in 50G-PON.

Closest papers

Nearest neighbours by meaning across the whole index.

Timing Skew Estimation of Time-Interleaved ADC based on Inter-Channel Correlations without Computing Derivative of Input Signal

eess.SP eess.SY ·2026-10-19 ·Bibhu Datta Sahoo, Gabriele Manganaro
similarity 0.52
Abstract

Time-interleaved analog-to-digital converters (TI-ADCs) enable multi-gigasample-per-second throughput in high-speed applications, but sub-picosecond timing skews among interleaved channels introduce large spectral artifacts that degrade dynamic performance. To continuously track parametric drifts without interrupting normal operation, background calibration is required. However, extracting timing skews under unknown inputs is challenging, and many existing correlation-based methods rely on resource-heavy derivative filters that restrict input bandwidth. This article proposes a novel background timing-skew estimation technique for two-channel TI-ADCs that overcomes these limitations. Closed-form timing-skew expressions are derived using: (a) adjacent-channel cross-correlation combined with single-channel auto-correlation for sinusoidal inputs, and (b) adjacent-channel cross-correlation for Wide-Sense Stationary (WSS) inputs, specifically bandpass-filtered wideband noise and Orthogonal Frequency Division Multiplexed (OFDM) signals. The derived analytical models are validated through comprehensive simulations, offering an efficient framework for real-time background calibration in high-speed data converters.

0.17

Receiver-Informed Transmitter for 200Gbps C-Band Direct-Detection PON With FFE-Free ONU

cs.IT physics.optics ·2026-09-29 ·Safiya Dabwan, Geraldo Gomes, Stylianos Sygletos
unusual similarity 0.51
Abstract · Accepted for poster presentation at ECOC 2026. Fig.1(b-c) axes typo is revised

We introduce and numerically demonstrate receiver-informed transmitter (RITX) waveform design for 200 Gb/s PAM-4 C-band direct-detection PON. Using 50 GHz optoelectronics, RITX achieves N1/E1 loss classes with FFE-Free ONU, enabling 40 km reach and 48.1%/66.7% network-wide complexity savings at 1:64/1:128 splits

0.33

A Hybrid Digital/Analog Polyphase Filtering Approach for High-Speed RF-DACs

eess.SP ·2026-11-06 ·Behdad Jamadi, Jungmin Lee, Tarun Cousik, Rohit Rangaraj, Jeffrey S. Walling
similarity 0.48
Abstract · 11 pages, 5 figures, 5 tables

This paper proposes a hybrid polyphase interpolation for RF-DACs that removes the need for full-rate digital commutation by using passive combining on the RF-DAC itself. A P-branch polyphase FIR filter is factored into M streams, each formed by a (P/M)-way digital commutator at fRF/M and driving a dedicated RF-DAC slice, giving either partial digital (1<M<P) or fully analog (M=P) recombination. We show that the slice array acts as a single full-rate DAC with an M-times longer zero-order hold, derive yield laws for slice gain, timing and unit-capacitor mismatch, and find that with retiming the binding requirement is sub-picosecond matching of the fRF clock arrival, so the best choice is the smallest M that closes digital timing. Two 28-nm digital macros, designed for a 12.8GSps output rate and verified by post-layout simulation, illustrate a 4-phase variant that closes timing up to 14.4GSps with its digital logic at fRF/4 and an 8-phase variant that closes timing up to 16GSps with its digital logic at fRF/8. The analog recombination is evaluated with a behavioral model of the slice array. The architectures target wideband software defined radio (SDR) platforms, including cognitive radio, electronic warfare, and satellite communications.

0.30

Distributed Fiber Monitoring on a Coherent DSP ASIC: Implementation of Longitudinal Power Monitoring

eess.SP physics.optics ·2026-11-19 ·Takeo Sasai, Yukinobu Nakajima, Minami Takahashi, Runa Kaneko, Masanori Nakamura +3 more
similarity 0.48
Abstract · 11 pages, 19 figures

Coherent DSP ASICs and transceivers to date report a rich set of optical link metrics, yet these remain cumulative over the link and provide no spatial localization. This paper presents the implementation design of fiber-longitudinal power monitoring (LPM), which recovers spatially resolved power profiles from received traffic, on a coherent DSP ASIC chip. We first identify the challenges specific to DSP implementation, and describe the enabling algorithm and architecture. We then present the key design considerations for retaining the estimation fidelity of the on-chip LPM during in-service operation. On this basis, we implement LPM on a coherent DSP, a 3-nm 800G low-power DSP ASIC housed in an OSFP pluggable module, which constitutes, to our knowledge, the first coherent DSP ASIC and transceiver to perform distributed fiber monitoring and data communication simultaneously. The on-chip LPM is experimentally validated over links of up to 1005 km using 400ZR+ and 800ZR+ traffic, with no measurable impact on Q factor or module power consumption. Multi-vendor interoperability is also demonstrated, where the on-chip LPM operates on signals transmitted by third-party transceivers. These results extend coherent DSPs from cumulative to spatially resolved monitoring, allowing pluggable transceivers, deployable from DCI to long-haul, to act not only as cost-efficient transmission elements but also as distributed monitoring points across diverse optical network infrastructure.

0.31

A Timing-Robust Frequency-Interleaved ADC with Embedded Analog Fourier Transform

eess.SP ·2026-10-02 ·Xingchen Chao, Yunqiang Xu, Qiang Yu, Christian Adam, Qiang Li
similarity 0.47
Abstract

Timing errors represent a fundamental challenge in high-speed analog-to-digital converters (ADCs). This paper presents a frequency-interleaved architecture with inherent robustness to timing errors. The frequency interleaving is achieved by an embedded analog Fourier transform (AFT), allowing accurate channel spacing. The charge-based passive AFT is able to share the capacitor array with the capacitive DAC of the subsequent data conversion. A circuit implementation for the complex-valued irrational coefficients in the AFT matrix is proposed, which eliminates the device-ratio-induced systematic errors. Measured at 10b 13GS/s, the calibration-free ADC achieves 45.8-dB SNDR and 56.1-dB SFDR at Nyquist. The ADC consumes 26.4mA from a single 1V supply, resulting in a Walden FoM of 12.7 fJ/conv.-step.

0.25

A 140.5$μ$W, 99.8% Accuracy, 96.1dB SNR BioZ IC for Real-Time Cell Analysis with On-Demand Push-Pull Excitation and Continuous-Time $ΔΣ$ T-D Readout

eess.SP ·2026-10-24 ·Jiayang Li, Junzhe Chen, Xin Zhang, Peiqing Li, Liwen Zhang +13 more
published similarity 0.47
Abstract · Accepted for publication in ISSCC 2027, Paper 12.6. 8 pages, 7 figures

This paper presents a bioimpedance IC combining an on-demand push-pull driver and continuous-time $ΔΣ$ T-D readout to address the trade-off between SNR, accuracy and power consumption. The driver delivers 200$μ$App with $\leq$0.14% THD while consuming 80.3$μ$A. Using a 6MHz clock, the readout achieves 53.6ps effective timing resolution at a 4k$Ω$ load (0.1-4Hz noise integration). The IC achieves 96.1dB peak SNR, 99.8% magnitude accuracy and 0.13$^{\circ}$ phase error at a maximum power consumption of 140.5$μ$W.

0.35

A Time-Encoded Analog Photonic Interposer for Energy-EfficientIntegration of Analog Vision Sensors and Analog Accelerators

cs.AR ·2026-09-02 ·Subhradip Chakraborty, Zihan Yin, Xuming Chen, Chengwei Zhou, Gourav Datta +1 more
similarity 0.45
Abstract

This work introduces a time-encoded analog photonic interposer that enables long-distance, high-fidelity transport of analog signals between spatially separated chiplets. Unlike prior silicon-photonic links limited to digital data, the interposer preserves analog information by converting amplitudes into timing intervals using an analog-to-time converter (ATC), transmitting them over a wavelength-division-multiplexed photonic link, and reconstructing values at the receiver without an explicit high-precision ADC/DAC data-converter pipeline. The link instead embeds an implicit 6-bit time-domain quantization and uses a single wavelength per processing element independent of bit precision. Evaluated in a fully analog vision pipeline with an in-pixel computing (IPC) sensor, it achieves a 2.04x energy--delay product (EDP) improvement over an 8-bit digital electrical baseline on the 560x560 Visual Wake Words dataset, with the advantage widening with link length even against a precision-matched 6-bit baseline. The pipeline holds 89.87% and 86.15% accuracy on ResNet18 and MobileNetV2 for VWW and generalizes across CIFAR-10 and ModelNet40 within 2% of the digital baseline.

0.26

A Reusable Four-Port S-Parameter to Link-Level Signal-Integrity Analysis Framework for High-Speed Detector Interconnects

eess.SY hep-ex ·2026-08-10 ·D M S Sultan, D. Bortoletto, R. Plackett, A. E. McDougall, A. S. Rotelli +2 more
similarity 0.45
Abstract

A reusable MATLAB signal-integrity (SI) framework is presented that converts compatible four-port S-parameter data, measured by VNA or obtained from electromagnetic simulation, into traceable link-level evidence rather than a single loss metric. Its contribution is the checked, traceable automation of established SI operations while keeping source data, model assumptions, analytical projections, and finite-record observations distinct. The framework is demonstrated on the four 1.25 Gbps differential routes (DP1-DP4) of the PPCB-1347-MuPix11 probe card using PTSL CST Microwave 3D-Solver-derived four-port S-parameters and a virtual time-domain solver. The automated pipeline preflights file structures, performs a power-normalized mixed-mode transformation, applies route-length-aware loss decomposition, constructs a causally loaded channel model, and propagates full PRBS-31 sequences into eye-diagram, conditional-BER, and 8b10b-coded-link analyses. At the 1.25 Gbps data rate (Nyquist 0.625 GHz), DP1-DP4 exhibit differential insertion loss (SDD21) from -0.350 to -0.300 dB, differential-to-common conversion from -31.038 to -28.236 dBc, and modeled FEB-input eye openings from 0.586 to 0.588 V. The comparison shows that path length alone is not an adequate SI ranking variable: DP3 has the lowest Nyquist insertion loss, DP1 the strongest differential-to-common isolation, and DP4 the largest modeled eye. All analytical BER values remain below the reporting floor and therefore do not support a BER ranking. By preserving the distinction between route-dependent waveform behavior, model projections, and finite-record observations, the framework provides an extensible basis for comparative high-speed-interconnect SI analysis from design review through calibrated VNA measurement interpretation.

0.04