CS Paper Radar

A Hybrid Digital/Analog Polyphase Filtering Approach for High-Speed RF-DACs

Behdad Jamadi, Jungmin Lee, Tarun Cousik, Rohit Rangaraj, Jeffrey S. Walling

eess.SP ·submitted 2026-11-06 13:38 UTC · v1

Abstract

This paper proposes a hybrid polyphase interpolation for RF-DACs that removes the need for full-rate digital commutation by using passive combining on the RF-DAC itself. A P-branch polyphase FIR filter is factored into M streams, each formed by a (P/M)-way digital commutator at fRF/M and driving a dedicated RF-DAC slice, giving either partial digital (1<M<P) or fully analog (M=P) recombination. We show that the slice array acts as a single full-rate DAC with an M-times longer zero-order hold, derive yield laws for slice gain, timing and unit-capacitor mismatch, and find that with retiming the binding requirement is sub-picosecond matching of the fRF clock arrival, so the best choice is the smallest M that closes digital timing. Two 28-nm digital macros, designed for a 12.8GSps output rate and verified by post-layout simulation, illustrate a 4-phase variant that closes timing up to 14.4GSps with its digital logic at fRF/4 and an 8-phase variant that closes timing up to 16GSps with its digital logic at fRF/8. The analog recombination is evaluated with a behavioral model of the slice array. The architectures target wideband software defined radio (SDR) platforms, including cognitive radio, electronic warfare, and satellite communications.

Comment
11 pages, 5 figures, 5 tables

Closest papers

Nearest neighbours by meaning across the whole index.

A Timing-Robust Frequency-Interleaved ADC with Embedded Analog Fourier Transform

eess.SP ·2026-10-02 ·Xingchen Chao, Yunqiang Xu, Qiang Yu, Christian Adam, Qiang Li
similarity 0.60
Abstract

Timing errors represent a fundamental challenge in high-speed analog-to-digital converters (ADCs). This paper presents a frequency-interleaved architecture with inherent robustness to timing errors. The frequency interleaving is achieved by an embedded analog Fourier transform (AFT), allowing accurate channel spacing. The charge-based passive AFT is able to share the capacitor array with the capacitive DAC of the subsequent data conversion. A circuit implementation for the complex-valued irrational coefficients in the AFT matrix is proposed, which eliminates the device-ratio-induced systematic errors. Measured at 10b 13GS/s, the calibration-free ADC achieves 45.8-dB SNDR and 56.1-dB SFDR at Nyquist. The ADC consumes 26.4mA from a single 1V supply, resulting in a Walden FoM of 12.7 fJ/conv.-step.

0.25

uhd-rfsoc: Bringing Off-the-Shelf RFSoC Boards to Unmodified UHD Applications

cs.NI cs.AReess.SP ·2026-11-13 ·Wei Cheng, Yiming Li, Junyao Zheng, Cheng-Bin Chen, Tingjun Chen
code/data similarity 0.53
Abstract

Next-generation wireless research relies on software-defined radios (SDRs) with more channels and larger bandwidth. The USRP family is one of the most widely used SDR platforms, and much of the wireless software ecosystem is built on top of the USRP hardware driver (UHD). However, each USRP model comes with a fixed channel count, bandwidth, and streaming capability. Off-the-shelf radio frequency system-on-chip (RFSoC) boards, on the other hand, integrate up to 16 analog-to-digital converters (ADCs) and 16 digital-to-analog converters (DACs) operating at several gigasamples per second (GS/s), but existing UHD applications cannot directly use them. We present uhd-rfsoc, an open-source FPGA design and host software stack that turns these boards, including the 16-channel ZCU216 and the RFSoC 4x2, into standard UHD devices without modifying UHD. Through standard UHD calls, applications can configure the carrier frequency, channel count, the per-channel I/Q sample rate, and the wire format. uhd-rfsoc combines timestamped, flow-controlled sample transport in the FPGA with data plane development kit (DPDK) packet processing and vectorized sample conversion on x86 and Arm hosts. The built bitstreams for a number of RFSoC board configurations with varying RF data converter rates, channel counts, I/Q sample rates, and wire formats all successfully pass UHD's built-in streaming benchmarks. We further demonstrate compatibility with unmodified GNU Radio flowgraphs, a custom GPU-accelerated transceiver digital signal processing pipeline, as well as the OCUDU and Duranta 5G radio access network stacks using both software and commodity user equipment.

0.35

A high-isolation wideband channelizer for MKID readouts: a custom HLS implementation on RFSoC

eess.SP astro-ph.IM ·2026-08-25 ·Alberto Hernandez Fernandez, David Diaz Martin, Jose Javier Diaz Garcia, Roger John Hoyland, Luis Fernando Rodriguez Ramos +2 more
publishedbenchmark similarity 0.49
Abstract · 18 pages, 7 figures. Submitted to the Journal of Astronomical Telescopes, Instruments, and Systems (JATIS). Extended version of Proc. SPIE 1…

We present a high-performance channelizer for Microwave Kinetic Inductance Detectors (MKIDs), designed to mitigate spectral leakage and scalloping loss through a 50% overlapping polyphase filter bank (PFB). The design is implemented on a Xilinx Zynq UltraScale+ RFSoC ZCU111 using a custom design - primarily in Vitis High-Level Synthesis (HLS), with the time-critical output serializer and glue logic in VHDL - that processes a 4.096 GSPS input stream with a per-branch super-sample rate (SSR) of 16. Rather than relying on aggressive 512 MHz clocking and vendor IP cores, our split-path architecture computes the delayed and non-delayed polyphase branches concurrently, so that the bulk of the channelizer operates at a robust 256 MHz while a single 512 MHz subdomain is confined to the BRAM-to-FFT section. This architectural parallelism enables a deep 16-tap prototype filter that doubles the filter depth of comparable high-speed systems and substantially improves channel isolation. We report the complete internal architecture of the reordering engine that implements the overlap, including two implementation hazards not documented in prior art: a pipeline-stage skew affecting state toggles in HLS, and the state-preservation requirements of a restartable design. The 2/1 overlapped channel response is validated in simulation - recovering the ~3.9 dB scalloping loss of a critically sampled channelizer to below 0.1 dB across the full 2 MHz channel - and characterized systematically with a 100-tone batch frequency sweep, while the parent readout system has been operated cryogenically with an MKID array in an adiabatic demagnetization refrigerator (ADR), identifying individual resonators in total darkness. The result is a resource-efficient, high-isolation benchmark for wideband frequency-division-multiplexed readouts.

0.48

Timing Skew Estimation of Time-Interleaved ADC based on Inter-Channel Correlations without Computing Derivative of Input Signal

eess.SP eess.SY ·2026-10-19 ·Bibhu Datta Sahoo, Gabriele Manganaro
similarity 0.48
Abstract

Time-interleaved analog-to-digital converters (TI-ADCs) enable multi-gigasample-per-second throughput in high-speed applications, but sub-picosecond timing skews among interleaved channels introduce large spectral artifacts that degrade dynamic performance. To continuously track parametric drifts without interrupting normal operation, background calibration is required. However, extracting timing skews under unknown inputs is challenging, and many existing correlation-based methods rely on resource-heavy derivative filters that restrict input bandwidth. This article proposes a novel background timing-skew estimation technique for two-channel TI-ADCs that overcomes these limitations. Closed-form timing-skew expressions are derived using: (a) adjacent-channel cross-correlation combined with single-channel auto-correlation for sinusoidal inputs, and (b) adjacent-channel cross-correlation for Wide-Sense Stationary (WSS) inputs, specifically bandpass-filtered wideband noise and Orthogonal Frequency Division Multiplexed (OFDM) signals. The derived analytical models are validated through comprehensive simulations, offering an efficient framework for real-time background calibration in high-speed data converters.

0.17

Burst-mode timing recovery based on fourth-power phase detector for passive optical networks

cs.NI ·2026-09-14 ·Ji Zhou, Haide Wang, Xiaofeng Zhang, Zhiyang Liu, Miao Yu +3 more
publishedunusual similarity 0.48
Abstract

Driven by the ever-increasing capacity demands, 50G passive optical network (50G-PON) is ready for practical application. It is highly challenging to realize 50GHz burst-mode analog components; therefore, based on 25GHz burst-mode analog devices, burst-mode digital signal processing (DSP) is introduced to achieve the reception and processing of 50Gb/s on-off keying burst signals. To optimize the power consumption and area of the DSP chip, a one-sample-per-symbol (1-SPS) analog-to-digital converter has been applied in 50G-PON. One of the main challenges is implementing burst-mode timing recovery (BM-TR) for the 1-SPS burst signal in 50G-PON. In this paper, we first propose a BM-TR based on the fourth-power phase detector (4PPD) for 50G-PON. We mathematically verify that 4PPD can directly compute the timing phase offset (TPO) from the 1-SPS signal without using training sequences, allowing for immediate BM-TR initialization within 20 cycles to prevent long convergence times. After the initialization, the feedback loop structure tracks the TPO changes based on the sign of 4PPD, the loop filter, and the numerically controlled oscillator. In conclusion, training-sequence-free 4PPD-based BM-TR achieves low burst overhead via fast convergence and is particularly effective for handling burst signals in 50G-PON.

0.37

A Reconfigurable Pipelined-SAR ADC with Embedded Compression for Temporal Compressed-Sensing Ultrasound Imaging

eess.SP physics.med-ph ·2026-08-28 ·Reza Pakdaman Zangabad, Xitie Zhang, Levent Degertekin, Shaolan Li
similarity 0.47
Abstract · 15 pages, 11 figures, Journal

Compact ultrasound imaging systems are increasingly constrained by receiver-side sampling, conversion, memory, and data-transfer requirements. This work presents a compressed-sensing pipelined successive-approximation-register analog-to-digital converter (CS-SAR ADC) for acquisition-side temporal compression of pre-beamformed medical ultrasound radio-frequency (RF) data. Pseudo-random polarity modulation and charge-domain accumulation are embedded in the SAR sampling network so that multiple consecutive RF samples are encoded into one measurement before quantization, supporting temporal compression ratios of $N_{cT}=1$, 2, and 4. The compressed outputs are recovered off chip using a probe-specific pulse-dictionary RF model and then processed with conventional ultrasound beamforming. A 65-nm CMOS prototype was measured with a 1.2-V supply and 50-MHz master clock. In the non-compressed mode, it operates at 10 MS/s, consumes 964.49~$μ$W, and achieves 44.12-dB SNDR and 56.40-dB SFDR for a 7.7-kHz input. The ADC output rates decrease to 5 MS/s and 2.5 MS/s for $N_{cT}=2$ and 4. Across all evaluated RF traces, median NCC values were 0.981 and 0.932, with median NRMSE values of 0.36 and 0.56, respectively. Wire-phantom localization error remained below 0.04 mm with no appreciable FWHM degradation. In the speckle-rich cyst phantom, SSIM remained 0.94 and 0.87, while CNR decreased from 3.534 in the reference to 2.047 and 1.379. These results demonstrate a hardware-realistic tradeoff in which temporal compression substantially reduces ADC conversion count and output data rate while preserving point-target geometry, whereas low-contrast cyst conspicuity is more compression-sensitive.

0.28

xCHEM: SDR-Based Multi-Link Channel Emulator for Real-Time Hardware-in-the-Loop Digital-Twin

eess.SP ·2026-10-28 ·Ali Saeizadeh, Gabriele Gemmi, Tamerlan Aghayev, Michele Polese, Pedram Johari +1 more
similarity 0.47
Abstract · 13 pages, 16 figures, 4 tables

This paper presents xCHEM, a radio-frequency channel emulator that inserts programmable channels between physical radios using a single NI USRP X4xx software-defined radio. External channel models stream impulse responses to its field-programmable gate array without firmware changes or interruption of signal processing. A streaming datapath implements six independently configurable directional channels across four radio interfaces. Each channel uses a sparse finite impulse response filter whose memory-backed delays decouple delay span from multiplier resources. The real and complex variants support 32 and 16 nonzero taps, respectively, with a maximum delay of 16666.62 ns and 4.069 ns resolution. Coefficient scaling and arithmetic right shifts control attenuation. Hardware measurements show root-mean-square errors of 9.5 ps in delay over the full span and 0.11 dB in attenuation. Multipath delays are recovered within one sample. An FPGA coefficient engine produces tested Doppler shifts from +/-1 Hz to +/-1 MHz with mean frequency errors below 0.032 Hz relative to quantized commands after carrier-offset calibration; at 200 Hz, it reduces the measured near-carrier spur by 53.3 dB compared with 1 kHz host updates.

0.39

A Time-Encoded Analog Photonic Interposer for Energy-EfficientIntegration of Analog Vision Sensors and Analog Accelerators

cs.AR ·2026-09-02 ·Subhradip Chakraborty, Zihan Yin, Xuming Chen, Chengwei Zhou, Gourav Datta +1 more
similarity 0.46
Abstract

This work introduces a time-encoded analog photonic interposer that enables long-distance, high-fidelity transport of analog signals between spatially separated chiplets. Unlike prior silicon-photonic links limited to digital data, the interposer preserves analog information by converting amplitudes into timing intervals using an analog-to-time converter (ATC), transmitting them over a wavelength-division-multiplexed photonic link, and reconstructing values at the receiver without an explicit high-precision ADC/DAC data-converter pipeline. The link instead embeds an implicit 6-bit time-domain quantization and uses a single wavelength per processing element independent of bit precision. Evaluated in a fully analog vision pipeline with an in-pixel computing (IPC) sensor, it achieves a 2.04x energy--delay product (EDP) improvement over an 8-bit digital electrical baseline on the 560x560 Visual Wake Words dataset, with the advantage widening with link length even against a precision-matched 6-bit baseline. The pipeline holds 89.87% and 86.15% accuracy on ResNet18 and MobileNetV2 for VWW and generalizes across CIFAR-10 and ModelNet40 within 2% of the digital baseline.

0.26