CS Paper Radar

Element-dependent buckling loads of stiffened panels under cantilevered shear

Lifeng Wang, Zhongli Qiu, Xuanhao Cheng, Run Du, Wenming Cheng, Min Xie, Xiong Rao

cs.CE math.NA ·submitted 2026-09-19 00:07 UTC · v1

Abstract

The linearized buckling load of a stiffened panel depends on the stress stiffness its shell element assembles. We read it from exported operators against three truncations of one second variation. The classic pass of ANSYS SHELL181 carries a rotation-rotation block pairing the drilling freedom with the bending rotations and its perturbation pass does not; removing the block recovers the perturbation load factor to 0.02%. SHELL281 carries block and couplings in both passes. Abaqus S4 matches the critical mode of the complete second variation to 1.0000 on the translations and its load factor to 1.7%, against 17% and 34% for the other two forms. On an optimized panel under cantilevered shear a 20-node continuum lies 3% to 6% above that form, S4 and SHELL281, 11% and 23% below both SHELL181 passes and 25% above Abaqus S8R, at the finest meshes. On a conventionally stiffened panel the SHELL181 passes stand 1.0% and 3.5% above the complete form, 9% and 21% at half the rib pitch; under a shear flow, on cylinders, open beams and under axial compression the three forms coincide and no pass parts by more than 0.3%.

Comment
27 pages, 7 figures, 11 tables

Closest papers

Nearest neighbours by meaning across the whole index.

Joint nonlinearity in a stiffened aluminium wingbox panel and what it requires of a reduced basis

cs.CE eess.SYmath-phmath.NA ·2026-09-09 ·Nikolaos D. Tantaroudas, Evangelos Papatheou
similarity 0.61
Abstract · 20 pages, 14 figures

A shell finite-element model of a stiffened aluminium wingbox panel, a laboratory structure shared by several experimental studies, is built with its plate-to-stiffener joints at the $78$ physical fastener positions and calibrated against measured modal data, a six-parameter sensitivity update of the substructure moduli within $\pm20\%$ reproducing the first five measured modes to $1.1$--$4.3\%$ with modal-assurance values of $0.88$--$1.00$. Making the fasteners nonlinear, at equal mesh, mass and damping, shows that joint nonlinearity enters the response strongly asymmetrically. Hardening is almost invisible, at most $+1\%$ in frequency, whereas softening or slipping the joints moves the first three resonances by $-2.1$, $-4.9$ and $-9.2\%$, and friction removes up to $80\%$ of the resonant peak before it recovers. Newmark integration of all $18{,}804$ degrees of freedom and a harmonic balance condensed exactly onto the joints and continued in arclength agree to $5.5\times10^{-4}$. A projection-based nonlinear model order reduction then locates the criterion that a jointed structure imposes on a reduced basis. The binding quantity is not the linear response, which eleven vectors reproduce to better than $0.01\%$, but the receptance of the structure between the joints, of which $126$ global eigenvectors carry about $2\%$, and without which the reduced model overpredicts the hardening shift of the fundamental by a factor of thirty and returns a value beyond the rigid-joint limit of the panel.

0.32

Shape optimisation of nonlinear Naghdi shells on discrete geometries

cs.CE math.NA ·2026-08-11 ·Ado Farsi, Alberto Paganini
benchmark similarity 0.48
Abstract · 19 pages, 10 figures, 6 tables. Revised manuscript submitted to Computers & Structures

We present an automated framework for the shape optimisation of a geometrically nonlinear, five-parameter Naghdi model on faceted triangulations. By recovering directors numerically, we remove the requirement for an analytic or spline parameterisation of the mid-surface, whereas partial selective reduced integration alleviates locking. The residual and tangent of symbolic energies are generated in an automated fashion building on Firedrake's and UFL's symbolic differentiation capabilities. Additionally, UFL's and pyadjoint's algorithmic differentiation enables automated first and second shape derivative evaluations that are verifiably correct via Taylor tests. The forward model agrees with the Sze/Abaqus semi-cylinder reference. A three-model mesh-refinement study indicates that geometry recovery and surface faceting have small effects on the predicted deflection. Numerical experiments show that 100 trust-region iterations suffice to reduce the squared-displacement functional of a semi-cylinder by 98.4% and the elastic strain energy of a bracket by 94.6%. The latter result is validated against a COMSOL benchmark. Non-uniqueness of optimal shapes is demonstrated by optimising initial designs subject to small perturbations. Comparisons with linearised designs distinguish optimisation performance from the accuracy of the predicted nonlinear response.

0.12

A Physics-informed Neural Network Approach for Robust Buckling Load Prediction and Reliability-Based Design of Thin Truncated Conical Shells

cs.LG ·2026-08-22 ·Devasmit Dutta, Budhaditya De, Rohan Majumder, Sudip Kumar Mishra
similarity 0.48
Abstract

Thin-walled truncated conical shells are widely used in aerospace, marine, offshore, and lightweight infrastructure systems due to their high strength-to-weight ratio and geometric efficiency. Their buckling resistance under axial compression, however, is highly sensitive to geometric imperfections, manufacturing tolerances, material variability, and nonlinear instability effects. Conventional design procedures rely on conservative knockdown factors (KDFs), such as those recommended in NASA SP-8019, which do not explicitly account for shell geometry, fabrication quality, data uncertainty, or target reliability. This study develops a physics-informed neural network (PiNN) framework for predicting critical buckling loads of thin truncated conical shells and integrates the trained surrogate within a reliability-based design (RBD) formulation. The model combines geometric and material descriptors with mechanics-informed features derived from shell stability theory and the localized reduced stiffness method (LRSM). A physics-informed loss function penalizes mechanically inadmissible predictions exceeding the theoretical elastic buckling load. The framework is trained and evaluated using 133 experimental Mylar conical shell tests under axial compression. Compared with a conventional deep neural network (DNN), the PiNN improves predictive accuracy, reduces mean absolute error, and enhances physical consistency. The trained PiNN is then used to evaluate reliability indices and calibrate safety-consistent KDFs for prescribed target reliability levels. Results demonstrate that the PiNN-RBD framework provides an efficient approach for uncertainty-aware design of imperfection-sensitive shell structures.

0.49

Compositional Aeroelastic Operators for Morphing Flexible Multibody Aircraft: A Geometric Framework with Structural Verification

cs.CE math.NAphysics.flu-dyn ·2026-08-15 ·Gelin Chen, Chen Song, Chao Yang
similarity 0.47
Abstract · 30 pages, 2 figures, 2 tables

Morphing flexible multibody aircraft require structural strain, aerodynamic geometry, surface velocity, and generalized loading to remain compatible as joints and flexible components change configuration. A compositional formulation is developed around an assumed material attachment between each lifting surface and a geometrically exact beam. Separating the component root pose from the section field shows that the body strain and elastic potential of a component depend on its own elastic coordinates, while upstream motion enters kinetic terms and external-load pullbacks. At element level, an exact relative logarithm $d$ supplies strain and potential energy, whereas a reference-anchored section coordinate $σ$ supplies deformed section geometry. Finite-order expansions retain the finite reference geometry exactly and truncate only endpoint perturbations. The attachment map then generates surface points, tangents, normals, velocities, and force Jacobians from common section kinematics. Euler--Poincare beam balance, moving-surface potential-flow relations, graph cotangent assembly, and the associated semidiscrete power identity are stated in a common twist--wrench convention. Collocation, pressure, equivalent-load, and structural-station sites are distinguished to expose their approximation errors. Verification gives the expected $N_d+1$ convergence order for degree-$N_d$ relative-log expansions. In a geometrically nonlinear cantilever comparison, a cubic static-manifold correction reduces mean full-record displacement error from $0.479$ to $0.255$ over four completed load cases. These results provide structural and interface-level evidence rather than validation of a complete aircraft aeroelastic prediction.

0.10

Cosserat Modeling of Trimmed Helicoid Soft Arms with a Separated-Section Constitutive Law

cs.RO ·2026-09-21 ·Zhihang Qin, Linxin Hou, Zeyu Zhong, Yuchen Sun, Wenci Xin +8 more
similarity 0.45
Abstract

Cosserat rod models for soft robots usually construct sectional stiffness by summing material properties over a common cross-section. This assumption becomes inaccurate for trimmed helicoid arms, where load-bearing helix domains are separated and connected only through sparse fused crossings. This paper formulates a separated-section constitutive law that evaluates each helix domain in its local frame and pulls its constitutive response back to the backbone, yielding an effective backbone stiffness. Sparse-fusion mechanics captures the additional compliance caused by relative motion between neighboring domains and determines channel-wise reduction profiles $η_c(s/L)$ for bending, torsion, and extension. The resulting effective sectional stiffness is strongly anisotropic: bending and extension are reduced by about one order of magnitude, whereas torsion remains close to the effective backbone stiffness. The resulting sectional law is embedded in a geometrically exact dynamic Cosserat model with GVS discretization and routed-tendon actuation. Across 103 measured configurations, the three datasets give pooled normalized position errors of $7.7 \ \%$, $6.7 \ \%$, and $7.8 \ \%$, while each full-arm solve requires approximately $0.3 \ \mathrm{s}$ on one CPU core (Intel Xeon, Cascade Lake, $2.8 \mathrm{GHz}$), enabling rapid model-based planning, state and load estimation, and morphology--control co-design for architected soft robots.

0.38

Component-wise hyperreduction for nonlinear solid mechanics problems

cs.CE ·2026-08-19 ·Stephan Ritzert, Jannick Kehls, Erik Faust, Hagen Holthusen, Stefanie Reese +1 more
similarity 0.44
Abstract

Hyperreduced nonlinear solid-mechanics components can be generated offline and reused as transferable building blocks across different assemblies, boundary conditions, meshes, material parameters, and constitutive models. We use proper orthogonal decomposition (POD) and energy conserving sampling and weighting (ECSW) on the component level and connect the substructures by mortar mesh tying. The POD modes and the ECSW weights and elements are computed offline from simulations of single components and the finite rigid body motions are treated by 12 additional rigid body modes per substructure. The numerical examples demonstrate errors below 1 \% for large quasi-static assemblies while evaluating less than 10 \% of the elements. The same component bases and ECSW elements are successfully reused for finite-strain viscoelastic dynamics, although they were trained only on elastic Neo-Hookean component simulations. These results indicate that component-wise hyperreduction can provide reusable reduced building blocks for modular nonlinear solid-mechanics simulations.

0.51

A Local Stabilized Isogeometric Formulation with Discontinuous Pressure for Mesh-Conforming and Immersed Analysis of Nearly Incompressible Elasticity

cs.CE math.NA ·2026-10-26 ·Ashkan Ali Madadi, Thomas J. R. Hughes
similarity 0.43
Abstract

Nearly incompressible materials arise in soft tissues, elastomers, gels, and other soft solids. Yet, numerical modeling remains challenging because displacement-based formulations can exhibit volumetric locking near incompressibility. Mixed displacement-pressure formulations address this difficulty but require compatible approximation spaces satisfying the inf-sup condition. In mixed formulations, discontinuous pressure spaces are attractive since pressure degrees of freedom can be condensed locally. In high-order isogeometric analysis, however, their Galerkin stability requires pressure-grid coarsening that increases with polynomial degree. Here, we develop a variational multiscale (VMS) stabilized mixed isogeometric formulation that retains this locality while substantially relaxing the restriction. The key observation is that VMS stabilization controls nonconstant elementwise pressure modes and is unconditionally stable with respect to its parameter, provided the elementwise constant pressure component satisfies the inf-sup condition. Consequently, for maximally continuous displacement splines, a pressure grid coarsened by a factor of two satisfies the constant-mode inf-sup criterion independently of polynomial degree. Local condensation then yields a displacement-only system, facilitating use in existing displacement solvers. The formulation is further extended to immersed isogeometric analysis with extended B-splines, pressure-cell aggregation, subdivision-based cut-cell quadrature, and weak enforcement of essential boundary conditions. Discrete inf-sup studies and convergence analyses in the Kirsch and Cook's membrane benchmarks demonstrate stability and show that the immersed treatment preserves mixed stability properties. The proposed framework therefore provides a local, high-order, and robust approach for nearly incompressible problems in mesh-conforming and immersed settings.

0.26

An FE2 model for shear-deformable beams considering periodic lattice-like truss mesostructures

cs.CE ·2026-10-06 ·Julian Ochs, Jens Wackerfuß
similarity 0.43
Abstract · 37 pages, 21 figures, 10 tables, 66 references

The increasing use of lattice-like architectures in load-bearing members, facilitated by advances in additive manufacturing, calls for efficient multiscale approaches to their structural analysis. For slender lattice-like structures, beam models provide a computationally efficient macroscopic representation while retaining the ability to account for the underlying lattice architecture through an homogenization approach. Although finite element squared (FE2) approaches combining beam models at the macroscopic scale with continuum models at the microscopic scale have been established, an FE2 framework combining a beam-based macroscopic model with a truss-based microscopic model of a lattice structure has not yet been reported. To address this gap, an FE2 framework is developed for three-dimensional shear-deformable beams with periodically repeated lattice-like microstructures and periodic displacement boundary conditions. The proposed FE2 framework introduces constraint equations that (a) prevent rigid-body translations and rotations of the representative volume element (RVE) without imposing additional kinematic restrictions and (b) ensure that the homogenized stress resultants and material matrix are independent of the selected RVE length. To mitigate artificial boundary effects arising at the boundaries of the lattice-like RVE, local correction factors are introduced. The framework is assessed through numerical studies of two- and three-dimensional lattice-like structures with different geometries, considering both geometric and material linearity and nonlinearity. The results demonstrate the independence of the homogenized stress resultants and material matrix from the selected RVE length and show good agreement with the corresponding reference models in all investigated cases.

0.28