CS Paper Radar

Designing an Efficient Excavator Bucket for Lunar ISRU: A Comparative Study with Vision-Based Fill and Displacement Analysis

Abdulla Hil Kafi, Tomoki Koshi, Jorge Casir, Kenji Nagaoka

cs.RO ·submitted 2026-09-22 05:53 UTC · v1
top venue

Abstract

This paper present a spiral-cavity wheel for lunar regolith excavation and a sensor-light evaluation stack that jointly estimates fill ratio (vision), sinkage (vision), and specific energy from actuator logs. In benchtop tests (four revolutions at 5, 10, and 15~RPM) against two literature baselines, the proposed wheel achieved higher excavated mass and fill ratio, delivering 2.2-3.0 times higher excavation rate while reducing specific energy by 29 % relative to a bucket-drum baseline. Normalized sinkage (mm/kg) was also lower, indicating stable traction without bogging. Effort-time traces show a steady torque envelope with repeatable cut-carry-dump cycles across speeds. We provide a retention index $η$ that correlates with fill ratio and a DEM setup that reproduces experimental trends with low error. Results suggest spiral-cavity wheels can replace heavier multi-actuator diggers when mass, simplicity, and energy efficiency are mission drivers.

Comment
Accepted and presentaed at the 2026 IEEE International Conference on Robotics and Automation (ICRA 2026)

Closest papers

Nearest neighbours by meaning across the whole index.

Toward Lunar Legged Robots: Field Deployment Lessons at LUNA

cs.RO ·2026-10-08 ·Adrian Fuhrer, Joseph Church, Oliver Fischer, William Talbot, Nicolas Faesch +4 more
similarity 0.64
Abstract · Proceeding to the IEEE iSparo Conference 2026

Legged robots are promising candidates for future lunar surface missions because they can traverse steep, loose, and obstacle-rich terrain that challenges conventional wheeled rovers. However, readiness for lunar deployment is limited by uncertainties in foot-regolith interaction, dust generation, illumination-driven perception degradation, and operational constraints. This paper reports lessons from the 2025 LUNA analogue campaign, where ANYmal-D and Magnecko traversed loose regolith simulant and crater-like terrain and collected long-horizon navigation and visual-inertial data under challenging lighting. We show that quadrupedal robots can traverse regolith simulant, but performance is affected by sinkage and slip, dust-generating contacts, and perception failures caused by overexposure, shadows, and low-texture regions. These results motivate tighter integration of regolith-aware locomotion policies, illumination-robust perception, repeatable analogue testing, and mission-level operational validation for future lunar legged robots.

0.22

A3P5 NEMESIS Integrated Rover Design for Environmental Reconnaissance and Robotic Sampling with Reproducible Mobility Analysis and an External Data Machine Learning Calibration Benchmark

cs.RO ·2026-09-16 ·Shafi Bin Sultan, Sabik Bin Sultan, Safwan Sadad
benchmark similarity 0.55
Abstract

A3P5 NEMESIS is a four-wheel rover intended to combine remote inspection, environmental observation and lightweight manipulation within one serviceable platform. This study develops a photo-constrained geometric reconstruction, a subsystem architecture and a reproducible analytical assessment while distinguishing physical prototype evidence from proposed functions. An exploratory search retrieved 5,000 bibliographic records across ten queries, yielding 4,897 distinct DOI records and 1,212 metadata candidates; selected primary studies and technical documents informed the design. The reconstructed configuration retains the carbon-pattern enclosure, independently steered wheel assemblies, folded manipulator, inclined camera mast and side sampling equipment. A declared 24 kg scenario predicts 3.28 newton-metres of gearbox-output torque per wheel on a 20-degree grade under equal load sharing; a separate static model shows how a 2 kg forward payload reduces the geometric front-tipping bound from 38.1 degrees to 32.7 degrees. These are design screens, not measured operating limits. A public-data calibration benchmark uses 7,344 eligible hourly observations, eight sensor/environmental predictors and chronological training, validation and test partitions. Validation-selected ridge regression achieves a held-out CO root-mean-square error of 0.502 milligrams per cubic metre, with a 95% daily-block bootstrap interval of 0.435-0.569 milligrams per cubic metre. This result concerns an external sensor array and cannot establish NEMESIS accuracy. The combined analysis identifies priority measurements, proposed control interfaces and mission-specific validation requirements. The contribution is a traceable engineering design study and evaluation framework for a prototype whose integrated field performance remains to be established.

0.27

Zephyron: Integrated Design and Analytical Evaluation of a Solar-Assisted Mobile Manipulator for Multimodal Environmental Reconnaissance and Distributed Visual Inference

cs.RO ·2026-09-22 ·Sabik Bin Sultan, Shafi Bin Sultan, Safwan Sadad
similarity 0.55
Abstract

Environmental reconnaissance needs mobile platforms that carry sensors, preserve measurement context, and return interpretable evidence under limited energy and communication. We present a literature-informed engineering design for Zephyron, a four-wheel rover with a front manipulator, environmental sensors, distributed computer vision, local recording, and a raised rear solar module. The design keeps the prototype layout but replaces unsupported numerical assumptions with an explicit component and geometry baseline. A reproducible search retrieved 5,000 records (4,858 unique) for screening, followed by targeted review of primary literature and manufacturer documentation. The baseline uses 165 mm wheels, a 12 kg mass budget, a 72 Wh battery-energy basis, and a 20 W photovoltaic module. With rolling-resistance coefficient 0.04, steady ascent of a 10 degree grade needs about 0.517 N m per wheel under equal load sharing. An illustrative 40 W motion load gives 1.44 h from 57.6 Wh usable energy, and a 25 percent driving duty gives 4.19 h without solar input; these are calculated scenarios, not measured performance. Sensor models show how integration time, calibration, temperature, and communication delay constrain interpretation, and a quality-aware stop-and-sample policy links these constraints to mission execution. Lightweight detectors, reference-based sensor learning, and executable data-integrity checks define a reproducible machine-learning evaluation pathway. The contribution is a traceable design and evaluation framework with editable 3D models, subsystem diagrams, and reproducible analytical data. Experimental validation is required before assigning payload, endurance, detection, or field-operating ratings.

0.21

Joint-State Inference for Autonomous Excavators Using Cab-View Vision-Control Fusion

cs.RO ·2026-11-10 ·Junwei Li, Jian Pan, Mengchi Cai, Shuai Zhao, Xizhuo Jiang +4 more
similarity 0.55
Abstract

Reliable state feedback of excavator front-end mechanisms is essential for autonomous excavation, yet retrofitting existing machines with dedicated joint sensors, external cameras, or visual markers can increase deployment and maintenance burdens. This paper proposes a closed-loop autonomous excavation framework for continuous inference of excavator joint states using onboard visual observations and control-related temporal information. The framework encodes structural cues from the current cab-view image, models short-term motion trends from historical joystick commands, and introduces a rolling state buffer for the bucket joint to preserve temporal continuity under severe occlusion. Mechanical joint-range constraints are incorporated into the learning objective to suppress infeasible estimates. The current cab-view image and inferred states are supplied to an Action Chunking with Transformers (ACT)-based control policy for online action generation. Experiments in an AGX Dynamics for Unity simulation environment under diverse operating conditions evaluate joint-state inference and end-to-end task execution. Across 20 autonomous excavation trials, the framework achieved a 95% task-completion rate, with an average joint-state-inference-and-control latency of 10.11 ms per step. The bucket-joint inference achieved a mean absolute error (MAE) of 0.965 degrees. These results demonstrate a sensor-light and computationally efficient joint-state-inference approach that can support closed-loop autonomous excavation with reduced dependence on additional sensing infrastructure.

0.10

Integrated Design and Reproducible Feasibility Analysis of a Four-Wheel Rover with Packet-Commanded Imaging, LiDAR Ranging, and Learning-Assisted Target Recognition

cs.RO ·2026-10-27 ·Sabik Bin Sultan, Shafi Bin Sultan, Safwan Sadad, Aranya Abeer Khan Prapya, Maria Sultan
benchmark similarity 0.55
Abstract · Research Manuscript for NASA HERC 2027

This study develops an integrated, reproducible design assessment for a four-wheel educational rover intended for the high-school remote-control division of the 2027 NASA Human Exploration Rover Challenge. The architecture combines commercial differential drive control, independently sprung wheel carriers, separate drive and task batteries, and a Raspberry Pi-based subsystem that executes received imaging and ranging commands. The analysis reconciles component lists with dimensioned computer-aided design views, derives mobility and electrical constraints, and connects sensor geometry to command execution. At the estimated mass of 10.919 kg, a 215 mm wheel rotating at 200 RPM produces a theoretical rolling speed of 8.105 km/h; consequently, the nominal motor label does not establish compliance with an 8 km/h design ceiling. A steady 20-degree climb requires at least 1.255 newton-meters per wheel under an assumed rolling-resistance coefficient of 0.10 and equal torque sharing. At 50 ft, an ideal 12-inch feature spans approximately 71 pixels across a full-resolution Camera Module 3 Standard image, while a 1-degree pointing error displaces the ranging ray by approximately 266 mm. An executed synthetic benchmark compares color-geometry rules and two linear support-vector classifiers on 2,400 generated board crops with scene-disjoint evaluation. A separate reference command executor is checked using mocked hardware. These software results and analytical sensitivities support a testable development plan; the study does not report physical rover trials. The principal contribution is a traceable connection between component choices, failure mechanisms, quantitative design limits, and reproducible verification tasks.

0.18

Robot-Assisted Deployment and Maintenance of Inflatable Modules for Lunar Habitation: A Field Demonstration

cs.RO ·2026-09-28 ·Kentaro Uno, Shamistan Karimov, Ashutosh Mishra, Elian Neppel, Hazal Gozbasi +3 more
published similarity 0.51
Abstract · Author's version of a manuscript accepted at the International Conference on Space Robotics 2026 (iSpaRo 2026). (c) IEEE

Long-term human habitation and in-situ development on the Moon open a new era of space utilization. In this context, robots are a key technology for facilitating the construction of future human outposts. Toward the deployment and establishment of human habitation modules on the lunar surface, we propose a combined system consisting of inflatable modules and a modular, reconfigurable robotic system. This paper presents a report demonstrating various robot-assisted task executions using real hardware, namely the modular and reconfigurable robot MoonBot and the inflatable module HIDAS, to enhance the reliability of their deployment and maintenance. The demonstrated tasks include robotic inspection during inflation, module position alignment, final safety locking, and three-dimensional mapping for post-deployment maintenance. All demonstrations were conducted either in a laboratory environment or at a lunar analogue test site. Finally, lessons learned are discussed to provide essential insights for this robotic application to future lunar habitation.

0.34

An Integrated Open-Source Stack for Vision-Based Autonomous Navigation of Wheeled Rovers

cs.RO ·2026-11-05 ·Iaroslav Kolomiets, Iaroslav Sheipak, Mikhail Reppo, Vsevolod Egorov, Viktor Chertopolokhov +1 more
publishedcode/data similarity 0.50
Abstract · Accepted at RiTA 2026

Vision-based rover autonomy requires integrating perception, localization, planning and platform-specific control under limited sensing and computing resources. We present an open-source ROS 2 stack for following directional arrows, reaching a terminal cone and returning autonomously to the start. It connects YOLOv8n detection and geometric direction, range and bearing estimation with RGB-D SLAM, wheel-inertial state estimation, kinematics-aware planning, behavior-tree mission management and STM32 actuation. Standard interfaces separate reusable autonomy from the hardware layer; a proportional path-following plugin supports low-speed rover motion. Public resources include software, configuration, a labeled dataset, trained weights and evaluation logs. On 478 held-out images, the detector achieves mAP@0.5 of 0.720 under the Ultralytics evaluator and outperforms a classical OpenCV baseline under a shared evaluation protocol. The reported perception latency is 25 ms on a Jetson Orin NX. Three missions, one indoor and two outdoor, demonstrate marker-guided navigation and autonomous return without operator motion commands or reported collisions. Field results document integration failures and corrective choices; repeated instrumented trials remain necessary to quantify physical navigation errors and reliability.

0.28

MARE: An Open-Source Lunar Rover Simulator with Shadow Ground Truth for Perception and Autonomy

cs.RO ·2026-10-20 ·Raúl Castilla-Arquillo, Miguel Olivares-Mendez
code/data similarity 0.50
Abstract · 10 pages, 16 figures, 3 tables. v2: adds a dataset with segmentation and depth baselines. Code: https://github.com/raulcastar/MARE-Lunar-Sim…

Lunar surface exploration increasingly relies on autonomous rovers that must perceive and traverse unstructured terrain under extreme illumination conditions. Near the lunar poles, low sun elevations produce long, high-contrast shadows that challenge stereo vision, terrain segmentation, and localization. Developing perception and navigation algorithms for these conditions requires large amounts of sensor data with accurate ground truth, which field campaigns and analog facilities can only provide at high cost and with limited variety. This paper presents MARE (Modular Autonomy and Rendering Environment), an open-source simulation suite for lunar rover perception and autonomy built on Unreal Engine 5 and ROS 2. MARE consists of three integrated components. Terrain Studio generates cratered and rocky lunar Digital Elevation Maps (DEMs) to build simulation scenes. A dedicated Unreal Engine project hosts two physics-based rovers with plugins for stereo, lidar, event, and Single-Photon Avalanche Diode (SPAD) cameras, streaming time-stamped sensor data and pixel-accurate ground truth. Lastly, a Guidance, Navigation, and Control (GNC) stack provides web-based mission control. Validation shows a mean Intersection over Union (IoU) of 0.79 between predicted and rendered shadows at low sun elevations, and stereo depth analysis verifies decreased pixel coverage in shadowed regions relative to sunlit terrain.

0.28