CS Paper Radar

Open-Source Multi-Wire SPI Readout for Wearable Ultrasound Probes

Federico Villani, Soumyo Bhattacharjee, Lisa Odermatt, Cédric Hirschi, Luca Benini, Andrea Cossettini

cs.AR eess.SP ·submitted 2026-10-01 12:56 UTC · v1
published

Abstract

Wearable ultrasound probes must transfer increasingly large acquisition payloads while maintaining compact, low-power electronics. In TinyProbe, the current bottleneck in data transfer occurs between the acquisition FPGA and the wireless system controller. This work presents an open-source, multi-wire SPI readout interface that uses serial command and address phases followed by a build-time-selectable dual- or quad-lane payload phase that is intended to address this bottleneck by increasing the potential bandwidth over the wifi limit while retaining compatibility with the Microcontroller-centric wearable US architecture. The interface emulates a serial flash memory, enabling compatibility with a broad range of microcontroller families and their existing peripheral interfaces. On the FPGA, the data path connects the existing acquisition FIFOs to the SPI interface through clock-domain crossing, sample reshaping, and packing into 32-bit words. Dual-SPI readout is integrated into the existing IGLOO2/SiWG917 TinyProbe architecture and verified at an SCLK frequency of 5 MHz. A separate Kria K26 testbed is used to characterize the FPGA SPI interface independently of the acquisition and wireless subsystems, demonstrating error-free transfers at SCLK frequencies up to 66 MHz. These measurements identify the SiWG917 multi-lane SPI implementation as the next bandwidth-limiting component and motivate a future upgrade of the system controller. The HDL and MCU implementations are released under a permissive open-source license.

Comment
4 pages, 3 figures. This work has been accepted for publication in the 2026 IEEE International Ultrasonics Symposium (IUS) proceedings. The final published version will be available via IEEE Xplore

Closest papers

Nearest neighbours by meaning across the whole index.

Open-Source Live-Reconfigurable Multi-Mode Wearable Ultrasound

eess.SP cs.AR ·2026-10-01 ·Cédric Hirschi, Federico Villani, Luca Benini, Andrea Cossettini
publishedunusual similarity 0.65
Abstract · 4 pages, 4 figures, 1 table. This work has been accepted for publication in the 2026 IEEE International Ultrasonics Symposium (IUS) proceedi…

Wearable ultrasound enables continuous deep-tissue monitoring, and a single programmable probe can operate in multiple complementary modes, such as structural A-mode and Doppler flow measurement. However, each operating mode requires dedicated measurement parameters and peripheral states, with no single configuration serving all modes on resource-constrained devices. Time multiplexing of operating modes introduces reconfiguration latency that lowers the effective mode repetition rate. To address this limitation, we present an open-source, transition-aware control stack for low-latency, in-session reconfiguration of the 32-channel TinyProbe wearable platform. Operating modes are described as hardware configurations, and host-side shadow registers track the peripheral states, enabling transition-specific register updates. Transition sequences are executed either by the host (over Wi-Fi 6) or by a firmware loop on the probe MCU. We validate the stack on a pulsatile-flow phantom by interleaving blocks of 25 to 100 pulsed-wave Doppler shots at 1.43 kHz PRF with single 16-channel A-mode acquisitions, changing channel configurations at every transition. Compared to full reconfiguration, the overhead per transition decreases from 30.2 ms to 11.6 ms (host-scheduled) and 3.1 ms (MCU-scheduled). For 75-shot Doppler blocks, the multi-mode repetition rate reaches 16.0 Hz (MCU-scheduled), 90.1% of the theoretical maximum of 17.7 Hz. Concurrent reconstruction of a Doppler spectrogram and a lumen-diameter trace demonstrates the functionality of time-multiplexed flow and structural monitoring.

0.56

U-Sonic: An Open-Source 8-Channel Ultrasound Transmit IP in a 130 nm RISC-V SoC

cs.AR eess.SP ·2026-10-01 ·Federico Villani, Nico Canzani, Marc-André Wessner, Philippe Sauter, Enrico Zelioli +3 more
published similarity 0.55
Abstract · 4 pages, 3 figures, 3 tables. This work has been accepted for publication in the 2026 IEEE International Ultrasonics Symposium (IUS) proceed…

Miniaturized ultrasound (US) probes require programmable and synchronized transmit (TX) excitation across multiple elements, while existing compact platforms often rely on limited microcontroller (MCU) pulse generators or closed-source fixed-function pulser devices. We present U-Sonic, an open-source digital US TX peripheral integrated into a 32-bit RISC-V system-on-chip (SoC). The implemented SoC integrates 8 pulser cores, while the parameterized architecture supports up to 16 channels. Each core generates single- or dual-tone bursts with programmable period, duty cycle, pulse count, polarity, and idle level, together with optional inverted stop pulses for active damping. A shared memory-mapped Open Bus Interface (OBI) enables synchronous start and stop of arbitrary channel subsets and supports composite bipolar, gated, and three-level excitation schemes. Functional correctness was verified in Verilator against a Python golden model over 4379 checked cycles across directed and randomized configurations, and confirmed on a Terasic DE10-Lite field-programmable gate array (FPGA). The design was synthesized and placed-and-routed in IHP 130 nm. The post-layout area in kilo gate equivalents (kGE), scales as 1.65 kGE plus 1.66 kGE per channel. The 8-channel instance occupies 14.9 kGE, corresponding to approximately 14.3% of the 104 kGE SoC. The register-transfer level (RTL), register descriptions, verification collateral, and software support are released as open source.

0.50

FIREQ: FPGA Instrumentation for Readout and Qubit control

eess.SY quant-ph ·2026-08-29 ·Giuseppe La Capra, Fabio Calabrese, Giorgio D'Amico, Christian Conti, Andrea De Simone +6 more
code/data similarity 0.54
Abstract · 15 pages, 9 figures

We present FIREQ (FPGA Instrumentation for Readout and Qubit control), an open-source RFSoC-based framework for the control and readout of superconducting qubits. FIREQ combines a modular AXI-compliant firmware architecture with a PYNQ-based software stack designed to support extensible hardware integration, deterministic experiment timing, and low-overhead execution of repeated calibration and characterization workflows. The firmware implements direct RF synthesis and acquisition, trigger-based sequencing, programmable pulse generation, frequency-multiplexed readout, and memory-efficient acquisition and waveform buffering. The software adopts a client-server architecture with streamed data transfer and dependency-aware configuration updates to reduce host-device and reconfiguration overhead during parameter sweeps. On an AMD Zynq UltraScale+ RFSoC ZCU216, FIREQ generates RF pulses up to 9.3 GHz with a pulse-duration resolution of 107 ps and an event-timing resolution of 1.7 ns. FPGA resource utilization is compared with representative open-source RFSoC control frameworks, showing a low BRAM footprint while retaining full-rate I/Q generation and acquisition. The RF output is characterized in terms of phase noise, noise spectral density, and inter-channel timing skew. End-to-end operation is validated on a superconducting qubit through resonator spectroscopy, Rabi, Ramsey, and relaxation measurements, yielding T1 = 6.94 us and T2* = 13.50 us. FIREQ can therefore be used both as a qubit-control platform and as an experimental environment for evaluating alternative control and readout IP architectures.

0.35

TinyAudio: Compact and Efficient Text-to-Audio Generation for Low-Resource Deployment

cs.SD eess.AS ·2026-09-25 ·Junxi Liu, Xiquan Li, Wenhao Guan, Yifan Duan, Zhikang Niu +3 more
similarity 0.52
Abstract

Text-to-audio (TTA) generation has advanced rapidly in generation quality and instruction following. However, representative systems often require around a billion parameters, limiting deployment on resource-constrained devices. This paper introduces TinyAudio, a compact flow-matching-based TTA model for low-resource deployment. At its core, TinyAudio uses TA-DiT, a 35M single-stream flow-matching Transformer. TinyAudio also includes TA-CLAP, a 32M audio-aligned text encoder, and TA-VAE, whose 20M decoder reconstructs 44.1 kHz audio from compressed latents. TinyAudio has only 87M parameters in total, over 90% fewer than representative billion-parameter pipelines, and uses 0.48 GB peak GPU memory. TinyAudio achieves competitive generation quality on AudioCaps and TTA-Bench. We further introduce TinyAudio-MF, a MeanFlow-accelerated model that enables real-time generation with a four-core CPU quota. Our results demonstrate a practical quality-footprint trade-off for low-resource TTA deployment.

0.27

VesperCSI: A High-Performance and Extensible CSI Acquisition Framework for Edge Wi-Fi Sensing

cs.NI cs.PFeess.SP ·2026-10-15 ·Kaan Baydemir, Sajjad Baghaee, Ilkay Ulusoy
code/data similarity 0.51
Abstract · 25 pages, 13 figures, 9 tables. Open-source implementation available at https://github.com/technicaluserx/vespercsi

Channel State Information (CSI) captures fine-grained changes in Wi-Fi channel propagation and provides a foundation for device-free sensing applications such as activity recognition, localization, and occupancy detection. The development of such applications depends on an acquisition system that can handle high-rate CSI streams while remaining extensible to the requirements of individual experiments. VesperCSI is an open-source, GPL-3.0-licensed redesign of FeitCSI for CSI acquisition with Intel AX200 and AX210 Wi-Fi interfaces. It targets high-rate acquisition on amd64 and aarch64 Linux hosts using fixed-capacity preallocated object pools and separate capture and consumer threads. A loadable plugin interface supports experiment-specific monitoring, storage, and processing. We evaluate VesperCSI and FeitCSI on Raspberry Pi CM4 receivers in a burst-traffic software crossover. At a 600-MHz all-core frequency ceiling and a target rate of 2500 frames/s, VesperCSI achieves mean sequence retention of 99.017-99.087% in 10,000-frame bursts, compared with 43.972-46.553% for FeitCSI. This ordering persists after exchanging the userspace programs between two receivers while retaining their respective drivers. The comparison therefore characterizes the tested software-and-driver packages rather than isolating userspace effects. These results support VesperCSI as a reusable acquisition component for edge-hosted Wi-Fi sensing under the evaluated workload and platform conditions.

0.50

Python-based RTL Generator Demonstrated on a Low-IF 2-FSK Wireless Communication System

eess.SY ·2026-08-17 ·Brandon P. Hippe, David C. Burnett
similarity 0.50
Abstract

Hardware optimization is critical in the design of efficient wireless communication systems. Wireless communication hardware often consumes a significant fraction of the total system's power budget, with much of this power used in circuits that reduce various types of noise, particularly in the analog front end. The Single-Chip Micro Mote, or SCuM, uses a crystal-free radio architecture and makes design trade-offs that favor power consumption over noise performance while maintaining standards compatibility with popular Internet-of-Things (IoT) protocols such as IEEE 802.15.4 and Bluetooth Low Energy. In the continued development of SCuM, we recognize that the digital baseband hardware developed can be more closely optimized with the architecture of the chip. In this paper, we present an extensible Python-based RTL generator that is closely linked to simulation and testing environments. This approach provides flexibility for use on different hardware platforms, such as tape-outs and FPGA implementations, and has promise in AI-assisted design workflows.

0.25

A single-precision floating-point systolic Givens-QRD Triangular Solver for MVDR Beamforming

cs.AR eess.SP ·2026-09-02 ·Athi Ram R S, Alwin A, S. G. Sreejeesh, J. U. Kidav
similarity 0.49
Abstract · 18 pages, 14 figures, 18 tables

Computation of adaptive beamforming weights in Minimum Variance Distortionless Response (MVDR) processing is a latency-critical operation that poses significant challenges for real-time hardware implementation. This paper presents an FPGA implementation of a systolic Givens-rotation QR decomposition pipeline for MVDR beamforming on a simulated 32-element ultrasound transducer array, using single-precision floating-point arithmetic. The design is deployed on a Zynq UltraScale+ FPGA at 100 MHz with three parallel kernel instances operating concurrently, achieving a measured throughput of 31,123 weight vectors/s at 90.9% parallel efficiency relative to the measured single-instance rate. At an estimated 2.451 W of programmable-logic power, and 5.286 W including the processing system, this corresponds to 12,698 and 5,888 weight vectors/s/W, respectively. Under a matched three-way dispatch, a 24-core Intel Xeon Gold 5220R at 2.20 GHz achieves 465,699 weight vectors/s at a measured 83.08 W package power, corresponding to 5,606 weight vectors/s/W. The FPGA therefore attains 2.3x the power-normalised throughput of the processor on a programmable-logic basis and 1.05x on a total on-chip basis. In contrast, the processor retains a raw throughput advantage of approximately 15x at this operating point. Numerical precision is validated against MATLAB float32 reference outputs from a Field II cyst phantom simulation, achieving a 100% pass rate with a root mean square error of 5.10x10^-7, confirming near-theoretical finite-precision behaviour without systematic bias.

0.38

A 140.5$μ$W, 99.8% Accuracy, 96.1dB SNR BioZ IC for Real-Time Cell Analysis with On-Demand Push-Pull Excitation and Continuous-Time $ΔΣ$ T-D Readout

eess.SP ·2026-10-24 ·Jiayang Li, Junzhe Chen, Xin Zhang, Peiqing Li, Liwen Zhang +13 more
published similarity 0.49
Abstract · Accepted for publication in ISSCC 2027, Paper 12.6. 8 pages, 7 figures

This paper presents a bioimpedance IC combining an on-demand push-pull driver and continuous-time $ΔΣ$ T-D readout to address the trade-off between SNR, accuracy and power consumption. The driver delivers 200$μ$App with $\leq$0.14% THD while consuming 80.3$μ$A. Using a 6MHz clock, the readout achieves 53.6ps effective timing resolution at a 4k$Ω$ load (0.1-4Hz noise integration). The IC achieves 96.1dB peak SNR, 99.8% magnitude accuracy and 0.13$^{\circ}$ phase error at a maximum power consumption of 140.5$μ$W.

0.35