CS Paper Radar

Adaptive Inductor and Frequency Management for Integrated Power Converters

Rami Rasheedi, Salma Abdelzaher, Inna Partin-Vaisband

eess.SY ·submitted 2026-10-05 15:46 UTC · v1
unusual

Abstract

This work presents a digitally controlled adaptive power conversion framework that dynamically co-optimizes inductor configuration and switching frequency to achieve high efficiency across a wide range of load conditions. Conventional buck converters are typically optimized for a single operating point, leading to efficiency degradation under dynamic loads due to mismatches between inductance, switching frequency, and load current. To address this limitation, a reconfigurable inductor architecture is proposed. With this approach, the effective inductance and switching frequency are adjusted at runtime with on-chip digital controller. An end-to-end design methodology is developed, integrating physics-based analytical modeling, finite element method (FEM) simulations, and an optimization framework to determine preferred operating points across the load range. The resulting configurations are stored in a lookup table and implemented in real time through a low-overhead control scheme. The system explicitly accounts for both inductor and switching device losses, enabling co-optimization of conduction and switching losses within current ripple and continuous conduction mode (CCM) constraints. To ensure robust operation under fast load transients, a hysteresis-based control strategy is introduced to mitigate temporary CCM violations caused by sensing latency. An entry-margin condition is derived under which continuous conduction is guaranteed for a bounded load slew rate. Simulation results demonstrate a 4.5 percentage-point improvement in average efficiency and up to a 32% reduction in average power loss relative to fixed configurations, highlighting the effectiveness of adaptive inductance-frequency management in integrated power delivery systems with dynamic load profiles.

Closest papers

Nearest neighbours by meaning across the whole index.

An Inductively Assisted N :1 Switched-Capacitor Ladder Converter

eess.SY ·2026-11-10 ·Sandeep Reddy Kukunuru, M Mahmudul Hasan Sajeeb, Rohit Reddy Karnaty, Loai G. Salem
similarity 0.57
Abstract

This paper proposes an inductively assisted N:1 switched-capacitor ladder buck (D-SCLB) converter that replaces the output-side switch in the bottom half-bridge of an N:1 SCLB with a small inductor placed in parallel with the ladder capacitors during the demagnetization phase. The flying capacitors share the load current delivery, lowering the average inductor current to (1-M)Iout and enabling continuous regulation with M=D/(N-1+D). A closed-form output-impedance model, valid for arbitrary N under both optimal and uniform switch sizing, is derived and compared against SC, SCLB, FCMC, and DPSC topologies. For a 4:1 48V-to-PoL design, the D-SCLB reduces the average inductor current by up to 20% and improves the equivalent output impedance by up to 30% relative to the SCLB. Two hardware prototypes on a low-cost two-layer PCB achieve a peak efficiency of 96.2%, with the D-SCLB using 49% smaller inductor volume than the SCLB at comparable efficiency. Model predictions agree with measurements to within 1.5% under heavy load.

0.19

Continuous-Discrete Dual-Domain Co-Design for Optimized Digital Control of Power Converters

eess.SY ·2026-11-04 ·Shen Chen, Jinjun Liu, Xuancai Zhu, Yanlong Li, Jisong Wang +4 more
benchmarktheory similarity 0.56
Abstract

Optimizing digital control for power converters typically involves designing continuous-time controllers and discretizing them via Euler, Tustin, or Generalized Bilinear Transform (GBT) methods. However, the intrinsic coupling between continuous-domain control parameters and discrete-domain implementation parameters remains underexplored, often leading to suboptimal performance. To bridge this gap, this paper first establishes a Non-Uniqueness Theorem, elucidating the coupling mechanism between dual-domain parameters. Based on this, two co-design methodologies are proposed to derive optimized parameter sets: the Explicit Frequency-Domain Analytical Method (EFDAM) and the Implicit Computer-Aided Search Method (ICASM). The EFDAM derives closed-form solutions by maximizing the crossover frequency and resonant magnitude via logarithmic frequency stability criteria, while minimizing discretization errors using Taylor-series bounds. The ICASM formulates the search for optimized parameters as a constrained multi-objective optimization problem, balancing bandwidth, resonant magnitude, and fundamental magnitude. To solve ICASM efficiently, two algorithms are introduced: the Multi-Start COBYLA (MS-COBYLA), which employs Latin Hypercube Sampling for physics-informed initialization to escape local optima, and the PSO-COBYLA hybrid algorithm, which couples global particle swarm exploration with local refinement. Experimental results on a 5-kW single-phase inverter with a Proportional-Integral-Resonant (PIR) regulator validate that the proposed methods outperform the conventional benchmark, achieving a 43.3\% reduction in the peak-to-peak current ripple measured at the zero-active-power operating point and an 11.7\%--35.9\% decrease in THDi across various harmonic profiles.

0.27

A Single-Inductor N:1 Resonant Switched-Capacitor Ladder Converter with Efficient Continuous Voltage Conversion Capability

eess.SY ·2026-10-07 ·Sandeep Reddy Kukunuru, M Mahmudul Hasan Sajeeb, Rohit Reddy Karnaty, Loai G. Salem
similarity 0.56
Abstract

This paper presents an N:1 resonant switched-capacitor (ReSC) ladder converter of an output voltage that can be regulated continuously below the native N:1 resonant ratio while maintaining high efficiency. The topology can be generalized to any N-to-1 dc-dc conversion application while requiring only a single inductor. Efficient wide-range voltage regulation is realized by operating the bottom stack of the ReSC switches as diodes to maintain their switching always in phase with the inductor current, and hence, circumvent circulating currents that increase the inductor RMS current and ohmic losses under frequency control. A theoretical model has been developed to predict the output voltage and efficiency of the converter, with simulation results confirming its accuracy for N = 1, 2, and 4. A hardware prototype on a printed circuit board is developed to validate the performance of the proposed frequency-controlled regulation scheme. The prototype achieves a peak efficiency of 97% (94.3%) with a load of 30Ohms (resp. 6Ohms) and an efficiency >90% while generating a 9V USB-compatible voltage from a 40V-to-60V input. The measurement results match the model predictions within 0.63% accuracy.

0.30

Stability Enhancement of Cascaded DC Systems via Source Output-Impedance Reshaping Using Model-Free Control

eess.SY ·2026-10-23 ·Wanrong Li, Shuhan Hu, Hengping Xiong, Runnan Wang, Huawei Yuan +2 more
published similarity 0.55
Abstract · Accepted at the 2026 CPSS & IEEE International Symposium on Energy Storage and Conversion (ISESC)

Cascaded DC systems may become unstable through source-load impedance interactions even when their constituent converters are locally stable. This paper proposes a source-side model-free control (MFC) method that reuses bus-voltage feedback to reshape the source output impedance while preserving nominal reference-to-output dynamics. The controller uses only nominal source-loop information and requires neither a load-converter model nor load-side measurements. A current-controlled buck source supplying a regulated buck-resistor load that exhibits constant-power load (CPL) behaviour at low frequencies is used as the case study. Impedance analysis predicts that the proposed MFC increases the maximum stable load power by approximately 50%, thereby improving the stability margin of the cascaded system. Switched-model simulations confirm preservation of the nominal reference-to-output response and show that the MFC-controlled system remains stable at load levels for which the baseline system becomes unstable.

0.40

How AI Load Swings Reduce Datacenter Power Conversion Efficiency

cs.AR eess.SY ·2026-10-23 ·Heetarth Joshi, Ali Alenezi, Fang Chen Lin, Prasad Enjeti, Xiaoyang Wang +1 more
similarity 0.53
Abstract

AI training and inference workloads make GPU power swing repeatedly between compute and communication phases. As a result, the cascaded converters in a datacenter rack keep moving between operating points with different efficiencies. This paper uses an energy based, cycle averaged method to quantify that effect along a 240 V AC to 400 V DC to 51 V DC rack power path, using measured efficiency curves of commercially available GaN based PFC and LLC converters. For a 1 Hz, 50% duty-cycle load swinging between 5 kW and 510 W, conversion efficiency falls to 95.97%, compared with 96.82% at the equivalent constant average load, a loss of 0.88%. When 51/48V to 1V point of load conversion to the chip rail is included, it is shown that the loss grows to 1.66% (89.45% vs. 90.96%). These results show that efficiency rated at average load overstates real world performance, and that the penalty grows with each load dependent conversion stage between the grid and the GPU.

0.24

Improved Single-Input Space Vector for DC-Biased Sinusoidal Current Control in Battery Cyclers

eess.SY ·2026-11-12 ·Manveer Aujla, Philip Lewoc, Harminderjit S. Toor, Ahmad Ali, Caniggia Viana +1 more
publishedunusual similarity 0.52
Abstract · 8 pages, 17 figures. Accepted version of a paper presented at the 2026 IEEE Energy Conversion Congress and Expo (ECCE), Vancouver, Canada

This paper presents improvements to the single-input space vector (SISV) concept for current control in a battery cycler based on a two-phase interleaved buck converter. The cycler is controlled to output a dc-biased sinusoidal current, enabling investigation of second-harmonic ripple effects on lithium-ion cell aging. A modified SISV generation scheme is introduced to track current references containing both dc and sinusoidal components, and an impedance-angle compensation method is proposed to decouple the d and q control axes without disturbing dc tracking. A dq phase-portrait visualization method is also introduced to evaluate transient performance for both SISV and proportional-integral-resonant (PIR) control methods. Simulation and experimental results validate dc-biased sinusoidal current tracking using PIR control and SISV control with different decoupling schemes. The phase-portrait framework allows for straightforward evaluation of transient performance for both SISV and PIR control methods and supports controller tuning to obtain desired trajectories. The results demonstrate the feasibility of SISV-based current control as an alternative to PIR control for battery-cycler applications. The proposed improvements support the development of battery cyclers capable of controlling both dc and sinusoidal current components.

0.46

Winding the Field, Not the Wire: Overlaying Magnetics to Improve Current Dynamics in Modular Power Electronics

eess.SY ·2026-11-02 ·Jinshui Zhang, Boshuo Wang, Hunter Cullina, Emmy Nelson Madore, Maya Clinton +2 more
unusual similarity 0.52
Abstract

Modular power electronics scale power capacity by distributing it across cascaded modules. State-of-the-art modular multilevel converters further introduce dynamic inter-module switched-capacitor exchange and balancing through parallelization. In larger converters, however, this mode needs inter-module inductance to control the equilibration currents. Specifically, differential-mode inductance limits these currents, but existing solutions require conductor re-routing and introduce parasitic resistance. This work presents a non-intrusive resistance-free differential-mode inductance solution: a figure-of-eight-shaped magnetic core that guides the magnetic flux path around existing conductors, such as high-current bus bars. This design adds differential-mode inductance without modifying the conductors. We fabricated a core that provides a 1.52 uH differential-mode inductance while suppressing the common-mode inductance to only 7% of the DM inductance. The core reduces the inter-module current surge from 20.46 A to 7.76 A. The original conductors remain intact.

0.37

PLL-Less Synchronization of Grid-Following Converters Using a Voltage-Driven Frenet Frame

eess.SY ·2026-11-13 ·Jinhui Chen, Huadong Sun, Shiyun Xu, Bing Zhao, Peng Han +1 more
benchmark similarity 0.51
Abstract

In grid-following converters, the synchronization path can transmit voltage disturbances to the current loop under weak or unbalanced grid conditions. This paper develops a Frenet-frame controller that derives its axes from the integral curve of the measured voltage at the point of common coupling. The tangential current governs active power, while the normal and binormal currents govern the transverse components of non-active power. Feedforward terms derived from the output filter model compensate curvature and torsion coupling, yielding identical nominal current dynamics across the axes. The controller operates without a phase-locked loop or sequence extraction. A reduced transverse model accounts for the finite bandwidth of geometric rate reconstruction and predicts a reduction in low-frequency coupling from voltage disturbances to current. Controller hardware-in-the-loop tests using real-time simulation of a three-phase four-wire converter show the shortest settling time after an active power reference step and the smallest peak power deviations during balanced voltage disturbances among the tested controllers. Under single-phase voltage unbalance, the method reduces peak binormal current and maximum phase-current total harmonic distortion relative to both benchmarks. It also settles to the commanded power in a weak-grid connection test where the phase-locked loop benchmark exhibits sustained oscillations.

0.38