CS Paper Radar

When to Trust the BIM: Identifiability-Aware LiDAR-Inertial--BIM Fusion under As-Built Deviations

Yujie Zhang, Yuxuan Guo, Xinbao Sun, Chunlei Zhao, Langqi Miao, Xiaohui Jia, Jinyue Liu

cs.RO ·submitted 2026-11-06 06:20 UTC · v1

Abstract

Building information models (BIM) can provide a global geometric reference for robot localization with LiDAR-inertial odometry (LIO). However, as-built deviations from the as-designed model mean that a disagreement between a scan and the BIM may arise from a pose error, an offset wall surface (an as-built deviation or an unmodeled object in front of the wall), or a shifted room, and in some geometries these explanations produce identical observations. In this paper, we formalize this attribution problem as fault identification over three fault classes and derive a geometric criterion for when attribution is possible. Building on it, we propose an identifiability-aware method that reports an attribution only when the fault is attributable; otherwise, it retains the candidates, defers BIM updates and BIM-based pose corrections in the ambiguous directions, and recovers once new references arrive. In the pre-registered two-dimensional study, on cases whose fault is detectable but not attributable, the method's conditional error rate was 0.83%, against 31.67% for a baseline with uncertainty-based abstention at the same answer rate. On the 5,600 attributable cases, the method reported a unique attribution 5,574 times, with no incorrect attributions. In paired fault injections in a laboratory room with its IFC model and on three floors of the SLABIM dataset, it raised no off-target attribution (0 of 168 conditions in the laboratory; 0 of 1,302 on SLABIM) and attributed all eight laboratory faults predicted to be attributable, whereas both reproduced baselines raised off-target structural flags in every setting.

Comment
24 pages, 12 figures, 11 tables (including appendices)

Closest papers

Nearest neighbours by meaning across the whole index.

GLIO2: A GPU-Parallelized Tightly-Coupled LiDAR-Inertial-GNSS System for Robust and Real-Time Global Localization and Mapping

cs.RO ·2026-10-08 ·Qi Zhang, Xikun Liu, Qijun Qin, Xiangru Wang, Junzhe Wang +3 more
similarity 0.64
Abstract · 23 pages, 16 figures, 8 tables; includes appendices

Globally consistent, real-time state estimation in large-scale, perceptually degraded environments is essential for autonomous vehicles and aerial robots, and requires fusing LiDAR, inertial, and GNSS measurements. Existing fusion methods, however, share a scan-to-map front-end with two failure modes. First, each scan is aligned to an incrementally built map that drifts under degeneracy, and once the estimate diverges the error is irrecoverable. Second, even without divergence, a registration biased by dynamic objects or wrong correspondences is propagated as a single pose constraint with an over-confident covariance, leaving its correspondences unavailable for GNSS to re-weight or relinearize. We propose GLIO2, a tightly-coupled LiDAR-Inertial-GNSS system whose GPU-parallel front-end jointly optimizes scan-to-multiscan LiDAR, IMU pre-integration, and raw GNSS measurements in a single sliding-window factor graph, sustaining real-time operation on edge hardware. A complementary offline back-end reuses the same cached factors to refine the entire trajectory in batch, completing the 30-min, 4.51-km UrbanNav Whampoa sequence in about 24 s. Across three public benchmarks (UrbanNav, MARS-LVIG, M3DGR) and self-collected UAV and vehicle data, GLIO2 attains the best overall accuracy among evaluated systems. On a 5.66-km bridge traversed at up to 96 km/h, where every competing baseline diverges under LiDAR degeneracy, it maintains 1.6 m horizontal accuracy. On an NVIDIA Jetson Orin NX, the full pipeline runs at about 25 Hz (39.60 ms per scan). The source code and datasets will be released.

0.21

Online Geometric Consistency Assessment of LiDAR Measurements via Recursive Bayesian Comparison

cs.RO eess.SY ·2026-11-07 ·Mingqiao Han, Qigeng Duan, Xuchen Liu, Jinqiang Cui, Xi Chen +1 more
similarity 0.64
Abstract

LiDAR-based localization and mapping systems produce registered point clouds that serve as geometric measurements for downstream estimation and navigation. Registration errors introduce duplicated surfaces and structural deformation into these measurements. In the absence of an independent reference, online assessment relies on geometry accumulated from earlier measurements. Such assessment requires tolerance to sampling variation and an accumulation process in which observations enter the history only after evaluation. We therefore formulate a recursive Bayesian comparison that couples geometric assessment with history maintenance. A Normal-Inverse-Wishart model represents historical voxel geometry and its uncertainty, while a weak isotropic reference adapts to current sampling. Comparing the marginal predictive support of the same current points under both models yields Normalized Drift Evidence (NDE). Assessment precedes assimilation: positive NDE triggers an alarm and preserves the preceding historical state; otherwise, the current observations update the history. Across 14 real-world sequences totaling approximately 73 min from four platform types, alarms identified all nine corrupted sequences and were absent from all five consistent sequences. In four representative scenarios with event references, first alarms occurred within 0.9 s of the reference times, with no preceding alarms. Cross-backend evaluation demonstrates consistent responses to reconstructed geometry. Ablation and controlled perturbation results establish the roles of uncertainty modeling, recursive history, displacement, and geometric support. Mean processing time is 4.2--6.1 ms per update at 1 Hz. In ten UAV trials, alarms initiated odometry isolation, landing, relocalization, and mission continuation.

0.27

MiCaDe: Online LiDAR-Camera Miscalibration Change Detection for Autonomous Driving

cs.CV cs.LG ·2026-11-03 ·Carlo Sgaravatti, Riccardo Pieroni, Matteo Corno, Sergio M. Savaresi, Luca Magri +1 more
code/datahot direction similarity 0.63
Abstract

Reliable multi-sensor perception in autonomous vehicles requires accurate calibration between cameras and LiDAR. However, calibration drift is often unavoidable in long-term deployments: vibrations, thermal effects, and minor mechanical shocks may alter the relative pose between sensors, leading to systematic errors in downstream fusion tasks. We propose MiCaDe (Miscalibration Change Detection), an online solution detecting when the extrinsic LiDAR-camera calibration parameters are no longer accurate by means of sequential change detection. MiCaDe requires no calibration targets, or modification of the perception stack, providing low false-alarm rates with negligible computational overhead. Our key insight is that 3D and 2D bounding boxes produced by standard object detectors should remain geometrically consistent under correct calibration. By matching cross-modal detections, we derive geometric consistency metrics that serve as sensitive indicators of extrinsic drift. These metrics are aggregated into fixed-size batches and scored against a reference distribution, producing a likelihood stream that is monitored by a Change Point Model (CPM). Crucially, the CPM accumulates statistical evidence over time, enabling detection of subtle drifts that would otherwise go unnoticed. Experiments on multiple long-sequence datasets and on a real-world dataset with physically induced miscalibration confirm reliable detection under diverse conditions. Code available at: https://github.com/CarloSgaravatti/MiCaDe.

0.35

Auditing Targetless Camera-LiDAR Extrinsic Correction before Recursive Use

cs.CV ·2026-11-03 ·Bo Ma, Weiqi Yan
hot direction similarity 0.62
Abstract

Camera-LiDAR fusion repeatedly uses an extrinsic transform in projection, association, and recursive state estimation. We study whether a targetless correction should be admitted to a downstream consumer only after separate audits of correction quality, confidence ranking, and recursive risk. Our log-disjoint protocol evaluates these stages under synthetic extrinsic drift on Argoverse 2 and treats cross-dataset and odometry experiments as bounded diagnostics. On 27 test-split logs, single-frame Canny alignment is harmful in the mild tier. Multi-frame alignment improves severe-tier rotation by 2.52 degrees but worsens translation by 0.177 m; its declared joint error-magnitude improvement is also negative (-0.158, 95% CI [-0.223, -0.098]), so the rotation gain is not a six-degree-of-freedom correction success. A zero-injection check moves away from the true extrinsic, and solver-disagreement AUROC on selected splits does not yield a validated nonzero-coverage risk-coverage operating point. In a 15-log final system role, the locked conservative policy admits no candidate and equals Raw, whereas Always-correct increases trajectory error. These results support an auditable separation of correction, confidence, and recursive contamination; they do not establish a deployable calibration gate, positive odometry or SLAM improvement, map consistency, or closed-loop safety.

0.28

NM-LIO: Multiple LiDAR-Inertial Odometry Addressing LiDAR Measurement Noise Discrepancy

cs.RO ·2026-10-03 ·Gunhee Shin, Seungjae Lee, Minho Oh, Dongkyu Lee, Jaeyoung Lee +2 more
published similarity 0.61
Abstract · 10 pages, 3 figures, 1 table. Published in the International Conference on Robot Intelligence Technology and Applications (RiTA 2024)

Multiple LiDAR-inertial odometry methods have been widely applied in robotic applications owing to their enhanced accuracy and reliability. However, adopting multiple LiDAR systems can be challenging due to the discrepancies in measurement noise across different LiDARs. Existing methods have typically overlooked the noise discrepancies, which can significantly affect accuracy. In this paper, we propose Noise-aware Multiple LiDAR-Inertial Odometry (NM-LIO) that addresses the noise discrepancies. We integrate a noise model to quantify the measurement noise of each LiDAR. Additionally, we estimate the uncertainty of the residuals based on the measurement noise, allowing the measurement model to capture the noise discrepancies. Our proposed method is evaluated on a public multiple LiDAR dataset and compared with state-of-the-art methods. The experimental results demonstrate that the proposed method can accurately estimate the odometry in various environments by accounting for the noise discrepancies.

0.27

VeriCalib: Verifiable Target-Based LiDAR-Camera Calibration

cs.RO ·2026-10-20 ·Xiangcheng Hu, Xieyuanli Chen, Feiyi Chen, Shengli Ren, Shiyang Chen +6 more
similarity 0.61
Abstract · 35 pages, 20 figures, 13 tables

Target-based extrinsic calibration estimates the rigid transform between sensors from a few observations of a known target, and its result is commonly assessed by the root-mean-square error of the fitted residuals. However, this scalar error is computed on the same observations and therefore cannot indicate whether to accept the result, re-extract, recollect or add observations. This paper presents VeriCalib, which formulates extrinsic calibration as a verifiable estimation problem and reports a calibration state. The key insight is a two-level extrinsic compensation mechanism, in which the extrinsic compensates the rigid part of each observation error at the residual level, and rotation and translation compensate each other at the parameter level. Consequently, the fitted residual can reveal neither an inconsistency between the observations and the model nor whether the estimated extrinsic is reliable in every direction. Accordingly, we assess the calibration through a structured covariance that jointly propagates the uncertainty of the camera and LiDAR board features with a known-geometry prior, and estimate its scale as a variance component from the residuals. On this covariance, we decouple rotation and translation to resolve the precision along each direction and guide data collection toward the weakest one. Since this precision presumes consistent observations, we further develop within-view and cross-view checks that examine the internal residual and the rigid discrepancy between observations, respectively, with thresholds that hold their significance level under an unknown noise level. We also extend the minimal detectable bias to the extrinsic to bound the smallest detectable fault along each direction. These criteria form a calibration state that indicates whether to accept the result or how to collect the data...

0.22

From LiDAR Maps to Visual Localization: Unified Visual Association for Robust Point-Line-Plane Pose Estimation

cs.RO ·2026-09-23 ·Wentao Zhao, Zikun Chen, Yihe Niu, Haoyu Chen, Jingchuan Wang
benchmark similarity 0.60
Abstract

Camera localization in a prior LiDAR map provides a persistent geometric reference for long-term robotic navigation, yet remains challenging because of the substantial modality gap between camera images and point-cloud maps. We present a unified localization framework that makes the LiDAR map visually addressable rather than relying on a dedicated image-LiDAR correspondence model. Map geometry and reflectivity are rendered into LiDAR-derived quasi-images with explicit 2D-3D provenance, enabling camera observations and rendered map views to share mature visual features and matchers for both global localization and continuous pose tracking. Point and line correspondences are established through this common visual interface, while the retained provenance recovers metric LiDAR geometry and line-supported planar constraints for pose estimation. To improve robustness under ambiguous associations and weak geometry, we further introduce a distribution-aware, observability-complementary optimization strategy. Instead of reducing matching ambiguity to a scalar confidence, candidate association distributions are propagated into directional pose-information uncertainty, and reliable structural factors are selectively reinforced according to their ability to complement the currently weak pose directions. Experiments on the EuRoC MAV benchmark and self-collected real-world sequences demonstrate accurate global localization and robust continuous 6-DoF tracking using only a pre-built LiDAR map as the persistent prior, including under severe illumination variations and dynamic occlusions.

0.14

Temporal-Aware Fusion for Robust Outdoor LiDAR Localization

cs.CV ·2026-09-29 ·Minghang Zhu, Zhijing Wang, Yuxin Guo, Chen Liu, Yongshu Huang +3 more
top venue similarity 0.59
Abstract · 10 pages, 8 figures, 6 tables, conference

LiDAR relocalization aims to estimate the global 6-DoF pose of a sensor in the environment. However, existing regression-based approaches often encounter limitations in dynamic or ambiguous scenarios, as they typically prioritize single-frame inference, leaving the potential of spatio-temporal consistency across scans not fully explored. In this paper, we propose a Temporal-aware Localization framework (TempLoc) designed to enhance the robustness of outdoor localization by effectively modeling sequential consistency. Specifically, a Global Coordinate Estimation module is first introduced to predict point-wise global coordinates and associated uncertainties for each LiDAR scan. A Prior Coordinate Generation module is then presented to estimate inter-frame point correspondences by the attention mechanism. Lastly, an Uncertainty-Guided Coordinate Fusion module is deployed to integrate both predictions of point correspondence in an end-to-end fashion, yielding a more temporally consistent and accurate global 6-DoF pose. Experimental results on the NCLT and Oxford RobotCar benchmarks show that our TempLoc outperforms state-of-the-art methods by a large margin, demonstrating the effectiveness of temporal-aware correspondence modeling in LiDAR relocalization.

0.30