CS Paper Radar

CleanCity-BinSense: An IoT-Enabled Smart Waste Management System with Configurable Real-Time Fill Monitoring and Nearest-Neighbor Route Optimization

Mohammad Adnan Kabir, Intifad Muhammad Sayeed

cs.NI ·submitted 2026-09-08 10:16 UTC · v1

Abstract

CleanCity-BinSense addresses inefficiencies in urban waste management in developing cities, where fixed-schedule collection routes lead to overflowing bins and wasted fuel. This paper presents CleanCity-BinSense, a low-cost, end-to-end IoT-enabled smart waste management system for scalable real-time waste monitoring and demand-driven collection. The system integrates a solar-powered sensor node with an ultrasonic sensor for real-time bin fill-level monitoring. A key contribution is a configurable sensing model based on two calibration parameters, FULL_DISTANCE and EMPTY_DISTANCE, enabling deployment across bins of varying sizes and geometries without firmware modification. Fill percentage is computed using a geometry-configurable linear normalization algorithm, validated through hardware experiments with a mean absolute error (MAE) of 0.38 cm, within the manufacturer-specified sensor tolerance. Sensor readings are transmitted via Wi-Fi to a centralized web platform providing role-based dashboards for administrators, operators, and drivers, along with a public real-time bin-status map. The system also incorporates a lightweight nearest-neighbor route planning algorithm using SQL Server's spatial function to generate proximity-based collection routes with low computational overhead. Experimental evaluation shows an average end-to-end system latency of 5.3 seconds, dominated by the sensing interval rather than network overhead, while route generation for typical urban collection zones completes in under 100 ms. These results demonstrate the feasibility of a low-cost, configurable, infrastructure-light smart waste management system for heterogeneous urban waste networks in resource-constrained environments such as Dhaka, Bangladesh.

Comment
8 pages,11 figures

Closest papers

Nearest neighbours by meaning across the whole index.

LoRIS: LoRaWAN-based IoT Platform for Sustainability Monitoring in Hotels

cs.NI ·2026-08-18 ·Yash Pandey, Angus Gray, Reza Serati, Oscar Zhu, Emil Juvan +7 more
unusual similarity 0.53
Abstract

The hospitality sector is a major source of global greenhouse gas emissions, water stress, and waste generation, yet sustainability reporting in hotels remains constrained by coarse, manually collected operational data. We present LoRIS (LoRaWAN-based IoT platform for sustainability monitoring in hotels), a LoRaWAN-based sensing system that delivers high-resolution measurements of resource consumption, environmental conditions, and guest behaviour across geographically distributed hotel properties. The architecture follows the canonical LoRaWAN reference model and is built for the operational realities of hospitality deployments: restrictive hotel IT policies, guest privacy expectations, rapid and reversible installation, and multi-year battery operation. Privacy-by-design guides modality selection and deployment zoning, and end-to-end encryption protects data from sensor to dashboard. This system has been running since February 2022 and currently spans 850 sensors of 19 types across 21 sites in Australia and Slovenia, covering both the AU915 and EU868 regulatory regions. The platform has generated over 202 million sensor records and ingests approximately 245,000 uplink messages per day on managed serverless infrastructure. Our system has been successfully used for seven field studies spanning food waste, energy consumption, and water consumption, including controlled intervention experiments that measure environmental outcomes and guest satisfaction in parallel. This system shows that LoRaWAN sensing can be deployed at scale in operational hotels without compromising guest experience or privacy.

0.29

Terra-Fi: Decoupling Sensing and Wireless Depths for Sustainable Deep Underground Monitoring

eess.SY cs.ETcs.NI ·2026-10-23 ·Kaiqiang Lin, Mohamed-Slim Alouini
similarity 0.48
Abstract · 8 pages, 4 figures, 2 tables, submitted to IEEE IoTM

Wireless underground sensor networks (WUSNs) enable in-situ monitoring of subsurface processes and buried assets to deliver substantial social and economic benefits across diverse verticals. However, meter-scale underground monitoring remains challenging since conventional WUSNs place the entire underground device at the target sensing depth, where severe soil-induced attenuation significantly degrades communication reliability and makes wireless energy transfer (WET) inefficient and even impractical. To address this limitation, we propose Terra-Fi, a novel shallow-hub and deep-sensing architecture that decouples the sensing depth from the wireless communication and energy-replenishment depth. In Terra-Fi, a shallow wireless hub is deployed at a depth favorable for communication, WET, and maintenance, while application-specific sensing probes are extended to meter-scale target layers through power-and-signal feeders. On this basis, we first examine the depth limitations of underground communication and WET and compare representative monitoring architectures. Then, we present its system architecture, operation flow, and potential benefits. Through a precision agriculture case study, our numerical results reveal that Terra-Fi establishes more robust wireless connectivity and a longer operational lifetime than conventional fully buried WUSN architectures, particularly at greater sensing depths and higher volumetric water content. Moreover, its performance gain can be enhanced through time allocation and transmission-configuration optimization. Finally, we pinpoint practical challenges and future research directions for deploying Terra-Fi into WUSN systems.

0.48

Anchor-Free Range-Free 3D IoT Localization in Buried Environments with Connectivity-Informed Power Selection and Temporal Refinement

eess.SP ·2026-10-29 ·Peyman Moeini, Mark Coates
similarity 0.48
Abstract

In underground and surface mines, wireless Internet-of- Things (IoT) tags deployed with ore or muck loads can support material and grade tracking after burial, when conventional ranging and surveyed localization infrastructure may be unavailable. Building on the three-dimensional Pro- traction Technique (3D-PT), this paper introduces 3D-PT with Power Selection (3D-PT-PS), which selects informative transmit-power levels from binary pilot measurements, and 3D-PT-PS with Temporal Refinement (3D-PT-PST), which incorporates recorded load-deposition times as weak, non- metric cues. Both methods are anchor-free and range-free and require no RSSI, measured ranges, surveyed anchors, pile dimensions, or material parameters. Monte Carlo simulations evaluate different pile sizes and tag densities. In a 5000-t crusher-pocket scenario with 125 tags, 3D-PT-PST achieves 6.12% mean NRMSE and 2.20 m 3D RMSE, reducing mean NRMSE by 13.5% relative to 3D-PT-PS and by 43.6% and 69.1% relative to calibrated MDS-MAP(P) and CATL, respectively. These results show that connectivity and timing provide complementary information.

0.27

SmartBike: A Low-Power Edge IoT System for Cycling Safety and Real-Time Awareness

eess.SP ·2026-10-08 ·Sogand Hashemi, Gonçalo Sarabanda Neves Loureiro, Catarina Pereira De Freitas Lima, Lyssa Ramaut, Liesbet Van der Perre
published similarity 0.47
Abstract · 5 pages, 4 figures, 4 tables. Presented at the 46th Symposium on Information Theory and Signal Processing in the Benelux (SITB 2026), Ghent,…

Urban cycling is a sustainable mode of transportation, but cyclists remain highly vulnerable in dense traffic because of limited situational awareness and the lack of active safety assistance on conventional bicycles. This paper presents SmartBike, a low power Internet-of-Things (IoT) platform for cyclist safety, combining blind spot monitoring, rider usage detection, localization, and wireless edge-to-gateway communication. The proposed system consists of a bike-mounted IoT node and a gateway assisted monitoring interface. The node integrates three time-of-flight sensors for blind spot detection, an IMU module for motion sensing and on-board speed estimation, a GNSS module for localization, and a saddle mounted piezo-electric transducer for event-driven wake up. To satisfy the energy constraints of the IoT node, the design employs piezo-triggered activation, application specific sensing rates, and compact connectionless Bluetooth Low Energy (BLE) advertisements for low overhead transmission. The firmware is implemented in Zephyr RTOS using a lightweight state machine architecture, while the gateway performs passive BLE scanning, payload decoding, and real-time dashboard visualization. The BLE payload is reduced to 11 bytes, and power analysis shows that sensing accounts for more than 90% of the total energy budget, while wireless communication represents less overall consumption. With a 12600 mWh battery, the estimated lifetime reaches approximately 21 months under typical commuting conditions (Average 40 min per day).

0.40

Energy-Aware Receiver-initiated MAC Protocol for Energy Harvesting IoT

cs.NI cs.ETcs.PF ·2026-10-08 ·Sohail Sarang, Praveen Kumar Donta, Dejan Vukobratović
unusual similarity 0.46
Abstract · Submitted to 34th Telecommunications Forum (TELFOR 2026)

Energy harvesting (EH) technology has emerged as a key approach for extending the operational autonomy of Internet of Things (IoT) devices. In this context, medium access control (MAC) protocols for EH-IoT make use of the harvested energy efficiently to enhance the application performance. However, many existing MAC protocols rely on stored energy the battery in devising energy-aware strategies, which can interrupt the device operation and hinder the execution of ongoing tasks in dynamic and low EH conditions. To address this, this paper presents an energy-aware receiver-initiated MAC protocol for EH-IoT devices, called EARI-MAC, that adjusts the duty cycle of the receiver device based on stored energy and current harvesting power using the mathematical formulation. This approach supports sustained receiver operation under low EH conditions and improved application performance when harvested energy is abundant. The performance of the EARI-MAC has been evaluated in simulation using the real solar data gathered in Novi Sad, for three consecutive days. The simulation results demonstrate that the EARI-MAC utilizes the available energy resources efficiently and improves the packet delivery ratio and network throughput by more than 10%, reduces the receiver energy consumption by 5.6% and 8.2% and energy consumption per bit by 9.6% and 13.9% compared with QPPD-MAC and energy-unaware MAC, respectively.

0.27

Don't Just Impute, Detect: Task-Aware Diffusion Pipelines for Edge Anomaly Detection

cs.LG ·2026-10-29 ·Jeongsu Park, Taehyeon Yun, Geonwoo Kim, Yuji Lim, Moohong Min
publishedcode/dataunusual similarity 0.46
Abstract · 11 pages, 6 figures. Accepted at the 33rd IEEE International Conference on High Performance Computing, Data, and Analytics (HiPC 2026)

Industrial Internet of Things (IIoT) edge pipelines routinely lose contiguous blocks of multi-sensor data to network dropouts and hardware faults. The standard remedy is a disjointed "impute-then-detect" pipeline whose imputer is trained only for Mean Squared Error (MSE). Such an imputer fills a missing block with the most probable normal pattern: a partially observed anomaly is smoothed back toward normality, and boundary artifacts on normal data raise false alarms. We call this imputation bias and propose the Task-Aware Diffusion Refiner (TADR), a conditional diffusion refiner trained against the loss landscape of a frozen downstream detector. Because back-propagating through the sampling trajectory is intractable, the task-aware terms act on the one-step clean-window estimate that the noise prediction already yields, so training costs no more than plain diffusion training. Under strict Point-to-Point evaluation over five seeds with paired significance tests, TADR raises F1 by $0.338$ over the unrefined detector on SMD ($p = 0.0015$), and the anomaly enhancement objective alone contributes $0.463$ in ablation. We also characterise when the method helps: the gain tracks the continuous, mutually redundant channels available and the anomaly evidence the outage removes, and it is absent on telemetry datasets dominated by one-hot command channels and on PSM. At ten sampling steps TADR runs in $41.4$ ms per window on a single CPU core, sustaining about $24$ concurrent 1 Hz streams from a $4.03$ MB model. Code and per-seed results are available at https://github.com/int-park422/TADR.

0.49

Retrospective Evaluation of Bluetooth RSSI Fingerprinting for Bin Localization on an Industrial Shop Floor

cs.NI ·2026-10-15 ·Saif Lakhani
similarity 0.44
Abstract · 2 figures, 1 CSV

This paper evaluates an archival Bluetooth Low Energy received signal strength indicator (RSSI) dataset collected for bin localization on an industrial shop floor. The installation used 24 fixed relays positioned on walls and Bluetooth beacons attached to bins, with each relay applying a Kalman filter to its own readings in firmware before publishing them. The primary survey produced 19,034 usable two-minute fingerprint samples across 90 known positions, with 23 relay measurements available as model features. We compare calibrated path-loss multilateration with two radio-map estimators: distance-weighted $k$-nearest neighbours and Random Forest regression. A random 70/30 row split measures recognition at surveyed positions, while a coordinate-grouped split reserves 27 entire positions for testing and measures interpolation to unseen positions. Random Forest achieved a median error of 0.66~m for surveyed positions, with 77.9% of estimates within 3~m and 96.3% within 10~m. For unseen positions, median error increased to 9.42~m and 55.5% of estimates were within 10~m. Path-loss multilateration produced a 19.41~m median error on unseen positions, close to the 19.62~m mean-position baseline. The results support RSSI fingerprinting for a fixed inventory of surveyed bin positions, but not precise continuous localization between survey points. Git history dates the original implementation to September 7, 2019. The evaluation code in this paper was written in October 2026 and is reported separately from the seven-year-old prototype.

0.24

A Real-Time Tsetlin Machine-based Non-intrusive Load Monitoring System on MCUs

cs.LG ·2026-08-19 ·Han Wu, Tianhang Tan, Shengyu Duan, Alex Yakovlev, Rishad Shafik +1 more
published similarity 0.44
Abstract · Accepted by International Symposium on the Tsetlin Machine (ISTM 2026)

Non-Intrusive Load Monitoring (NILM) systems estimate individual appliance energy consumption from a single aggregate meter, without requiring separate sensors for each device. By installing a single meter that measures a building's total electricity consumption, NILM algorithms can determine the active status of each appliance. However, traditional NILM systems use computationally intensive optimization algorithms to process offline data, limiting their capability for on-device deployment, where sensitive household data must be processed locally. This paper proposes a Tsetlin Machine (TM)-based NILM framework, targeting real-time applications on resource-constrained microcontrollers (MCUs), enabling privacy-preserving edge deployment. The problem is reformulated as a classification task, and the proposed approach achieves an average precision of 90% and recall of 96% for two-appliance classification, and 77% precision and 80% recall for four appliances on the REDD dataset. The trained model occupies only 17 KB of flash memory and achieves an inference latency of 0.43 ms on an ESP32, demonstrating its suitability for NILM applications on MCUs.

0.33