CS Paper Radar

Overlap-free multi-material topology optimization for minimum compliance in two and three dimensions by level-set-based negative-mapping interpolation

Dong Wang, Qianglin Ran, Xuanliang Wang, Wei Xiang, Wenming Cheng, Run Du

cs.CE math.OC ·submitted 2026-08-18 16:17 UTC · v2
publishedunusual

Abstract

Gray elements and material overlaps at the interfaces limit density-based multi-material topology optimization. This article extends the level set-based negative-mapping interpolation to the multi-material proportional topology optimization of macro-scale structures in two and three dimensions. An alternating active-phase algorithm decomposes M-phase problems into two-phase sub-problems described by level set functions; an evolutionary strategy removes the need for sentitivity analysis; and the negative-mapping interpolation eliminates the overlaps of the phases in the interface elements. Cantilever and half-MBB beams in two dimensions and a cantilever beam in three dimensions, with three and four material phases, give smooth boundaries, no gray elements and overlap-free designs. The compliance lies below the SIMP value in four of the eight two-dimensional cases and 0.3%, 0.4%, 4.8% and 12.7% above it in the other four. The influence of the material properties, of the interface treatment and of the algorithmic parameters is also examined.

Comment
39 pages, 16 figures, 11 tables
DOI
10.1080/0305215X.2026.2746638

Closest papers

Nearest neighbours by meaning across the whole index.

Multimaterial topology optimization using SIMP, DMO and gSF: A comparative study with honeycomb tessellations

cs.CE ·2026-09-22 ·Bhargav kumar Duru, Prabhat Kumar
similarity 0.56
Abstract · NCMDAO2026 conference paper

This paper presents a comparative study of multimaterial topology optimization (MMTO) using the extended SIMP, Discrete Material Optimization (DMO), and generalized shape functions (gSF) approaches. The computational domain is discretized into hexagonal cells. Each cell is connected to its neighbors with edges. This characteristic reduces mesh-related effects on the optimized designs compared with conventional triangular and quadrilateral discretizations. Structural compliance is minimized at the prescribed volume fractions. The method of moving asymptotes is employed to update the design variables. The resulting optimized topologies are compared in terms of material distribution, structural performance, convergence behavior, and the characteristics of the obtained material interfaces. The comparative investigation provides insights into the working principles and performance of the extended SIMP, DMO, and gSF interpolation schemes for MMTO.

0.57

Multi-Material Topology Optimization for Targeted Structural Dynamic Vibration Attenuation

cs.CE ·2026-10-22 ·Bir Bahadur Chaudhary, Bidhan Pandey, Bin Ouyang, Shiguang Deng
similarity 0.53
Abstract

Resonance-induced excessive vibrations can degrade performance, reduce reliability, and shorten the service life of engineering structures. To reduce the risk of resonance, structural natural frequencies are generally engineered to be shifted away from excitation frequencies. To achieve these frequency shifts, topology optimization provides a systematic approach to tailor structural stiffness and mass as an effective inverse design approach. Multi-material topology optimization exploits the high-dimensional design space of spatially varying material constituents by simultaneously optimizing material selection and spatial distribution over the design domain, offering great flexibility in controlling natural frequencies. This study proposes a multi-material topology optimization that attenuates excessive structural dynamic vibrations in free-vibration scenarios via a novel multivariate weight-based interpolation method. Additionally, to address non-smoothness due to mode switching amid optimization, we employ a bound formulation with an auxiliary scalar design variable to replace the max-min eigenvalue objective with constraints on individual eigenvalues. Furthermore, we study and compare three optimization formulations for multi-material design to attenuate vibrations, including maximizing fundamental eigenfrequency, maximizing the gap between adjacent eigenfrequencies, and excluding frequencies from targeted frequency bands, which are smoothly approximated by a proposed rational polynomial formulation. Numerical examples are presented to demonstrate the effectiveness and applicability of our proposed method.

0.30

Machine-learning-assisted multiscale topology optimization of functionally graded superimposed lattice structures

cs.CE ·2026-08-28 ·Prashant Kumar Gupta, Jonathan Stollberg, Dominik Schillinger, Mohammad Ashraf Iqbal
benchmark similarity 0.49
Abstract

Functionally graded lattice structures enable lightweight designs with spatially tunable stiffness and density, but their use in multiscale topology optimization is limited by the cost of repeated computational homogenization. This work presents a machine learning-assisted multiscale optimization framework for regular superimposed lattice structures. The unit cell is formed by combining body-centered cubic, face-centered cubic, and simple cubic lattice components, each controlled by an independent geometric parameter. Offline computational homogenization is used to generate effective stiffness data, which are then used to train a Cholesky-constrained neural network surrogate. This representation reconstructs the homogenized stiffness tensor in a physically admissible form. A separate neural network is trained to predict relative density from Monte Carlo-based density estimates. We incorporate our surrogates into a two-stage topology optimization strategy. First, a macroscale topology is obtained using the solid isotropic material with penalization (SIMP) method. The resulting solid region is then used for microscale lattice optimization, where the local lattice parameters are updated using the method of moving asymptotes (MMA). The trained stiffness and density surrogates replace repeated online homogenization during this stage. The method is demonstrated on a three-dimensional Messerschmitt-Bölkow-Blohm (MBB) beam benchmark, producing spatially varying lattice parameters and relative density fields consistent with compliance minimization under a material constraint.

0.27

HGTO: A Unified Graph-Based Physics-Informed Formulation for Structural Topology Optimization

cs.LG ·2026-09-14 ·Kangzheng Liu, Uday Kumar Punna, Leixin Ma
similarity 0.48
Abstract

Density-based topology optimization is typically structured as a nested sequence of material updates, structural analyses, and sensitivity assessments. While neural density parameterization and dual-field physics-informed approaches provide data-free alternatives, most existing methods represent density and displacement as coordinate fields and make limited use of the discrete relationships inherent in the finite element mesh. The present study introduces HGTO, a unified graph-based formulation that extends complete neural topology optimization from coordinate space to finite-element graph space. Element densities are parameterized on the element graph derived from the mesh, and the structural state is determined on the corresponding node--element hypergraph. Finite element kinematics, numerical quadrature, constitutive response, and force assembly remain explicitly defined operations within the differentiable computation. The material field and equilibrium state are therefore coupled through a common finite-element incidence structure. Numerical studies show compliance comparable to conventional density-based optimization at substantially lower computational cost than a representative coordinate-based dual-field neural method. The same coupled formulation accommodates high-resolution and irregular meshes, three-dimensional structures, finite deformation, and elastoplastic response.

0.46

Lattice Structure Optimization for Additive Manufacturing: Manufacturability-Driven Design and Pareto Front Construction

cs.GR ·2026-09-27 ·Yu Xing, Yang Liu, Lin Lu
published similarity 0.46
Abstract · This manuscript is an English translation of a Chinese article accepted for publication in the Journal of Computer-Aided Design & Computer G…

Lattice metamaterials support lightweight, multifunctional structures, while additive manufacturing (AM) enables complex geometries. Yet multiphysics lattice design faces two challenges: efficiently constructing well-covered multi-objective Pareto fronts under limited budgets, and satisfying manufacturing constraints such as overhangs, enclosed cavities, and restricted powder-removal channels. We propose a manufacturing-constraint-driven method for lattice optimization and Pareto-front construction. Differentiable manufacturing constraints are embedded in inverse-homogenization topology optimization, enabling joint optimization of physical performance and manufacturability. A progressive Pareto-front mechanism uses a density-generation network to learn latent representations of high-quality lattices, interpolates neighboring nondominated representations, and decodes them into initial density fields for subsequent optimization. Newly found nondominated solutions update the network and sample set, progressively expanding the manufacturable set. On 3D periodic unit cells, with 1000 optimization runs, network initialization achieves a 92.60% success rate and 916 manufacturable samples, versus 78.30% and 776 for random initialization. Its Pareto front reaches a hypervolume of 0.0787, compared with 0.0675 for random initialization. The results show that the method efficiently constructs broadly covered manufacturable Pareto fronts for multiple physical properties.

0.38

CAST: Cast-Admissible Generative Design and Shape Optimization with Paired Depth Images

cs.LG ·2026-10-19 ·Jihoon Kim, Yongmin Kwon, Namwoo Kang
similarity 0.46
Abstract

Deep generative design can produce complex geometries, but unconstrained representations may create undercuts that prevent release from a two-part mold. We present CAST, which reformulates three-dimensional shape generation under a selected mold-opening constraint as a two-dimensional image generation problem using paired top and bottom depth images. Each valid depth pair defines one material interval along a selected mold-opening direction, so reconstructions exclude undercuts in that direction by construction. Diffusion models generate candidate shapes in this representation, and a finite element analysis (FEA) guided optimizer refines the same two boundaries. We evaluate diffusion-based generation with limited training data comprising 211 SimJEB bracket designs. On SimJEB brackets, FEA-guided refinement with a volume penalty reduced compliance in 193 of 200 generated candidates. The median reduction across all candidates was 36.8 percent in the optimization FEA model. Reconstruction of existing brackets revealed a mass--stiffness trade-off: filling occluded regions increased material volume and reduced displacement under the evaluated loads. Paired depth images thus connect generative exploration and structural refinement in a shared design space that preserves the selected pull-direction restriction.

0.24

Topology optimization of multimaterial aircraft pylons using generalized shape function approach

cs.CE ·2026-09-23 ·Swagatam Islam Sarkar, Prabhat Kumar
similarity 0.46
Abstract · NCMDAO2026 conference paper

As the primary structural component connecting the engine to the wing or fuselage, an aircraft pylon requires optimized structural efficiency; this paper provides topology optimization of multimaterial pylons using the generalized shape function (gSF) approach. The gSF method uses $n$ natural-coordinate design variables per element to provide optimized designs up to $2^n$ distinct material phases while promoting close to discrete material layouts in conjunction with the density and formulated Heaviside projection filters. Pylon structural compliance is minimized subject to volume constraints. Exploiting the geometric features of a typical pylon structure, multimaterial evolution is performed on a corresponding 2D design domain representing the midplane, with up to 14 candidate materials. The optimized two-dimensional layout is then extruded to achieve the corresponding three-dimensional optimized pylon structure. The Method of Moving Asymptotes is employed to achieve the final design variables. The resulting convergence histories exhibit smooth and stable objective minimization. The results highlight the capability of the multimaterial topology optimization framework to effectively optimized aircraft pylons with multiple candidate materials, without requiring a considerable expansion of the design variable set.

0.33

Multi-Material Topology Optimization of Phononic Crystals for Targeted Elastic Wave Bandgap

cs.CE ·2026-10-22 ·Bir Bahadur Chaudhary, Wenfeng Li, Ting Chen, Xinmai Yang, Candan Tamerler +2 more
similarity 0.46
Abstract

Phononic crystals are periodic elastic structures that exhibit frequency bandgaps within which elastic waves cannot propagate. The formation and width of these bandgaps depend on the spatial distribution of material properties within periodic phononic unit cells. In this work, we propose novel topology optimization formulations to achieve multi-material design of phononic crystals for bandgap optimization at targeted frequencies, where we discover the influence of spatially varying properties of base materials on the band structures that block and permit elastic wave propagation. Specifically, we model wave propagation by Floquet-Bloch theory and solve the resulting eigenvalue problem by the finite element method along the boundary of the irreducible Brillouin zone. We first propose a multivariate weight-based method via a novel interpolation scheme that maps the design variables of an arbitrary number of candidate materials into effective density and stiffness for elastic wave-propagation calculations, where bandgaps arise from the contrast in the stiffness and inertia among material constituents. We then develop two formulations for bandgap optimization. The first formulation maximizes the gap between two adjacent frequency bands using a bound-based approach, where we introduce two auxiliary scalar variables as additional design variables and incorporate them directly into the design objective, yielding a linear, differentiable design objective, with the eigenfrequencies entering the formulation through associated constraints. The second formulation places a bandgap over a user-defined target frequency range through a dynamic band-pairing strategy, where we adaptively identify the relevant pair of adjacent bands amid optimization iterations. Towards the end, we validate the bandgap performance of our designs against the transmission loss spectra computed from COMSOL Multiphysics.

0.35