CS Paper Radar

Electrospun Fields: 3D Nano-Fiber Material Computation as Design Method

Wai Lok Wan, Ayah Mahmoud, Sergio Mutis, Avantika Velho, Annie Xing, Behnaz Farahi

cs.GR cond-mat.softcs.RO ·submitted 2026-08-24 21:39 UTC · v1
publishedcode/dataunusual

Abstract

We present a robotic electrospinning platform and design method for depositing nanofiber membranes onto non-planar, three-dimensional conductive geometries. Conventional electrospinning relies on fixed emitters and planar grounded collectors, which restricts deposition to flat substrates: on concave geometries, field shielding prevents fibers from reaching recessed regions, and material bridges across elevated features instead. We address this with a custom end-effector integrated with a six-axis UR20 arm. The tool carries a localized stepper-driven syringe pump that maintains consistent polymer flow independent of orientation, and routes high-voltage DC (up to 25 kV) directly to a robot-mounted needle, turning the arm into a mobile emitter with full kinematic control over position, orientation, working distance, and traversal velocity. Toolpaths that continuously reorient the emitter along surface normals give access to concave topologies unreachable by fixed-axis systems. We characterize the resulting deposition behavior in two parts. A catalog of four bio-compatible polymer systems (PEO, PVA, keratin-PEO, silk-PEO) establishes the operating envelope, reporting deposition speed, jet stability, fiber size, alignment, and durability for each. A taxonomy of 3D-printed conductive scaffolds spanning geometric primitives, hybrid compositions, and square, triangular, and hexagonal lattices links collector geometry to fiber alignment, density, and cross-void bridging. We also demonstrate programmable grounding, in which selectively energized pins in an array steer deposition without changing physical geometry. Assembly instructions and toolpath-generation code are released as an open-source repository.

Comment
15 pages, 10 figures. Published in Proceedings of the ACM on Computer Graphics and Interactive Techniques (SIGGRAPH 2026). Open-source hardware and toolpath code: https://github.com/Critical-Matter-MIT-Media-Lab/Custom-3D-Electrospinning
Journal ref
Proc. ACM Comput. Graph. Interact. Tech. 9, 3, Article 43 (July 2026), 16 pages
DOI
10.1145/3816080

Closest papers

Nearest neighbours by meaning across the whole index.

AI-guided robotic in situ fabrication of curvature- and tissue-adaptive wireless bioelectronics

cs.RO ·2026-11-13 ·Hiroyuki Tetsuka, Jiaju Ma, Naomi Kumano, Minoru Hirano
similarity 0.59
Abstract

Personalized bioelectronic devices for wound therapy require not only conformal fabrication on complex body surfaces but also functional adaptation of their electrical characteristics to individual wound geometries. Here, we present an AI-guided robotic in situ printing platform for fabricating wireless wound electrotherapy devices directly on transparent wound dressings. The system integrates a 3D vision camera, a six-degree-of-freedom robotic arm, direct-ink-writing, and geometry-aware RF design optimization. AI-based wound segmentation is used to determine wound dimensions and local surface curvature, while the reconstructed three-dimensional geometry is incorporated into the electromagnetic design of the receiving coil and interdigitated electrodes. In contrast to conventional approaches that use surface geometry only for trajectory generation, the proposed method accounts for both anatomical curvature and tissue dielectric loading to compensate for geometry-induced shifts in resonant behavior. A printable silver ink was characterized in terms of rheology, dimensional reproducibility, electrical resistance, and electromechanical stability, and was used to fabricate multilayer wireless devices directly on curved polyurethane dressings. Wireless power transfer, impedance characteristics, and electric-field delivery were evaluated experimentally and numerically. Finally, robotic in situ fabrication was demonstrated on an anthropomorphic tissue-equivalent forearm phantom, where the measured dielectric properties of the phantom were incorporated into the RF optimization, enabling resonant operation near the target frequency of 25 MHz. This work establishes a perception-to-design-to-fabrication framework for geometry-adaptive wireless bioelectronics and provides a technological foundation for future physical-AI-enabled manufacturing of personalized on-body electrotherapy devices.

0.29

Selectively Actuated Fiberbots for High-precision Minimally Invasive Surgery

cs.RO ·2026-10-08 ·Jinshi Zhao, Libaihe Tian, Alex Ranne, Qindong Zheng, Yue Li +7 more
similarity 0.55
Abstract · 7 pages, 7 figures

Long, slender instruments are essential for minimally invasive surgery (MIS), but achieving precise distal manipulation becomes increasingly difficult when actuation extends along the entire instrument. Here, we present an electrothermally actuated fiber-based robot designed for MIS procedures, in which Joule heating is concentrated in the distal active segment. The fiber is fabricated using a thermal drawing process and uses embedded metallic wires for thermal actuation. This robotic fiber, 1.9 mm in diameter and 1.2 m in length, can precisely manipulate surgical laser fibers with positional precision below 100 $μ$m. The compact size of the fiber robot allows it to pass through the working channel of a flexible endoscope, while keeping both devices mechanically uncoupled to allow independent motion. A phantom demonstration combining the robotic fiber with a da Vinci instrument conceptually demonstrated its compatibility with existing endoscopic systems for clinical applications. Our robotic fiber enables precise distal motion and holds the potential to improve clinical outcomes by enhancing precision in MIS procedures.

0.33

Tip Manipulation in Soft Everting Robots via Wall Retraction and Deployable Fingers

cs.RO ·2026-09-19 ·Nelson Badillo Perez, Niccolo Pagliarani, Matteo Cianchetti, Robert D. Howe
similarity 0.52
Abstract · 38 pages, 6 figures and supplementary information

Soft everting robots can traverse long, confined paths by continuously growing, yet active interaction remains limited to a single tool fixed at or near the tip, unable to be repositioned on demand and difficult to reconcile with the robot's soft body. We introduce a tip-manipulation and multi-tool deployment strategy for soft everting robots based on wall retraction, implemented with a base roller assembly that independently meters membrane flow in the outer wall while a tail spool regulates growth in the internal tail section. Coordinated wall and tail actuation decouples robot length from membrane-material position, enabling membrane-mounted devices to be transported, exposed, and repositioned at selected locations near the distal tip. We pair this capability with ultralight pleated inflatable fingers integrated into the membrane, fabricated from TPU-coated nylon with an internal airtight bladder. The fingers achieve large bending at low pressures (approximately 100 degrees at 50 kPa in high-pleat designs) and generate blocking forces up to 1.9 N, while remaining limp during transport. The system demonstrates adaptive grasping across diverse household objects (21 to 550 g; 16 to 200 mm), three-dimensional object manipulation and stacking, environmentally braced extension, distal camera panning for confined-space inspection, and controlled sequential payload delivery. These results enable embodied and reversible tip manipulation for soft growing robots in cluttered and tortuous environments.

0.25

Effect of Twisted-Yarn Architecture on Pressure and Proximity Sensing Characteristics of Textile Capacitive Sensors for Robotic Skin

cs.RO physics.ins-det ·2026-08-14 ·Ishtia Zahir, Eslam Saleh, Maryam Rezayati, Güunter Grabher, Gaffar Hossain
similarity 0.49
Abstract · 10 pages. Submitted to IEEE Transactions on Instrumentation and Measurement

Textile-integrated capacitive sensors offer flexible and conformable tactile sensing for wearable electronics and human-robot interaction; however, the influence of yarn-level architecture on capacitive transduction characteristics remains insufficiently quantified. This work presents a textile capacitive sensing platform based on silver-coated yarns coated with polydimethylsiloxane and assembled into one-, two-, and four-layer twisted configurations. The influence of effective electrode overlap area and inter-fiber separation on the capacitive response is systematically investigated, enabling architecture-dependent tuning of pressure and proximity sensing characteristics. Pressure was calculated using the localized single-fiber contact area, corresponding to stresses of 0.4-3.9 MPa. Increasing the layer number improved mechanical strength and sensing performance: elongation at break increased from 37.5% to 62.5% and 85.0%, while the maximum load increased from 23.3 to 42.7 and 89.7 N. Sensitivity increased with layer number and frequency, reaching 0.1331 MPa$^{-1}$ for the four-layer sensor at 100 kHz. The four-layer configuration also exhibited low hysteresis, minimal thermal drift from 25 to 90 $^\circ$C, and stable operation over 15,000 cycles. Proximity detection ranges of 60, 50, and 40 mm were obtained for the one-, two-, and four-layer sensors, respectively, revealing an architecture-dependent sensitivity-range trade-off. A 4$\times$4 textile sensing array enabled spatial contact mapping, while robotic-arm integration demonstrated real-time touch and proximity detection with an end-to-end robotic system latency (from detection to robot reaction) of 403 ms. The results establish yarn architecture as a tunable design parameter governing the measurement characteristics of textile-integrated capacitive sensing systems.

0.12

Geometry-Dependent Properties of Physically Crosslinked PPy-PVA Hydrogels Enable Tunable Iontophoretic Drug Delivery

cs.RO physics.med-ph ·2026-10-22 ·Heather Jin Hee Kim, Mohsen Alishahi, Kyuin Park, Mikaila K. Roncevich, Larissa M. Shepherd +1 more
top venueunusual similarity 0.47
Abstract

Objective: Iontophoretic drug delivery has primarily relied on current modulation to regulate drug transport. Here, we investigate hydrogel geometry, microstructure, and local electric fields as alternative mechanisms for controlling transdermal delivery. Methods: Bovine serum albumin (BSA) was encapsulated in polypyrrole-polyvinyl alcohol (PPy-PVA) hydrogels. Five geometries, including Hilbert curve-based designs, were fabricated to vary pore architecture and local electric field distributions. We optimized PPy content, drug loading, and current density. Electric fields were evaluated using finite element analysis, and microstructures were characterized by scanning electron microscopy. Drug transport was assessed using Franz diffusion cells with artificial membranes. Results: Hydrogel geometries exhibited distinct microstructures and electric field distributions. Iontophoresis substantially enhanced permeability compared with passive diffusion, while individual geometries produced different cumulative release, flux, and permeability profiles. The average iontophoretic permeability was (3.80 +/- 1.93) x 10^-5, exceeding previously reported values using artificial membranes. Conclusion: Geometry-driven fabrication of drug-loaded hydrogels enables tunable transport characteristics under both iontophoretic and passive conditions. Significance: Geometry-mediated control offers an alternative approach to regulating iontophoretic drug delivery without requiring individual current-density modulation.

0.38

Freeform Programmable Liquid Crystal Elastomers via Monolithic Integration of Co-Optimization and 4D-Printing

cs.CE math.OC ·2026-10-23 ·Yibo Wang, Asad Farooq Ahmed, Weichen Li, Weiyun Xu, Xiaojia Shelly Zhang
similarity 0.47
Abstract

Liquid crystal elastomers (LCEs) are active materials capable of large, reversible thermally induced actuation, offering significant potential for applications such as artificial muscles and soft robotics. However, their broader deployment is hindered by the lack of a unified design-to-fabrication framework, the strong coupling among geometry, director fields, and manufacturing constraints, and the difficulty of reliably translating complex designs into physically realizable architectures. Here, we present an autonomous and monolithic integration of co-optimization and 4D printing that enables the end-to-end design-to-realization of versatile programmable LCE architectures with superior precision, complexity, and versatility. The proposed framework establishes a unified design strategy that co-optimizes the freeform multilayer geometry and fully continuous layer-specific director distributions, and subsequently translates the optimized fields into fabrication-ready DIW toolpaths through an automated manufacturing-aware pipeline. To bridge computation and realization, we develop an optimization-centered 4D printing approach with automated, fabrication-aware toolpath generation tailored for direct ink writing of LCEs. With the proposed design-to-fabrication paradigm, we experimentally realize architectures that exhibit complex, non-intuitive thermo-mechanical behaviors. Experiments achieve highly challenging prescribed functionalities beyond the reach of intuition-based approaches and show excellent agreement with numerical simulations across all samples. This work establishes a generalizable inverse design and physical realization of freeform programmable LCE systems, enabling function-oriented and optimization-driven intelligent LCE applications for next-generation soft robotic and responsive material engineering.

0.23

MUSBRIC: LEGO-Compatible Pneumatic Muscle Bricks for Reconfigurable Musculoskeletal Robots

cs.RO ·2026-10-29 ·Qiyao Wang, Yinglei Zhu, Liang Zhou, Wenzhe Gong, Xin-Jun Liu +1 more
similarity 0.47
Abstract · 6 figures. Qiyao Wang and Yinglei Zhu contributed equally to this work. Improved HTML rendering of Figure 1; scientific content unchanged

Musculoskeletal robots combine compliant actuators with articulated skeletons, but exploring alternative configurations often requires repeated fabrication. We present MUSBRIC, a modular hardware platform and accompanying MuJoCo-based simulator for reconfigurable musculoskeletal robots. LEGO-compatible endcaps turn fiber-reinforced extensile pneumatic artificial muscles into reusable, plug-and-play muscle bricks that connect directly to standard LEGO components. Experimentally identified actuator behavior supports corresponding musculoskeletal simulations. An elbow-joint prototype validates load-dependent flexion and extension, showing that pulley-guided routing enables reversible motion and a mechanical stop stabilizes the straight posture. A robotic hand demonstrates compliant grasping and multi-joint construction. Matched hardware and simulation sweeps across 15 leg configurations demonstrate systematic exploration of attachment geometry, while a quadruped assembled from four legs demonstrates walking. Together, these demonstrations span mechanism analysis, configuration exploration, and functional robot construction within a single reconfigurable system. The hardware designs and simulation code will be released as open source soon to facilitate reproduction and further development.

0.35

Helping Hand: A Continuum Robotic Grasper for Traction in Single-Channel Endoscopic Submucosal Dissection

cs.RO ·2026-11-11 ·Bendavid Maimon, Thompson Wong, Aedan Mangan, Sukjun Kim, Michael C. Yip +1 more
similarity 0.46
Abstract · 7 pages, 9 figures

Endoscopic submucosal dissection (ESD) is a minimally invasive approach for removing large polyps from the colon and offers many benefits compared to other surgical approaches. However, ESD is technically very challenging to perform, leading to limited adoption by physicians. We propose the Helping Hand, a two-segment continuum robotic grasper that, together with an electrosurgical knife, enables tissue traction and cutting within a single 3.7 mm working channel. We achieve this functionality by creating a slot at the base of the Helping Hand that lets the electrosurgical knife extend out, enabling countertraction and cutting through one instrument lumen. We evaluate the Helping Hand's workspace and its ability to provide traction forces from different starting configurations. Finally, we demonstrate the full workflow by isolating and removing tissue in an ex vivo chicken thigh, illustrating the potential for the Helping Hand to help improve ESD procedures.

0.29