CS Paper Radar

Design and Experimental Validation of the Separation and Deployment System for the CHERI Lunar Micro-Rovers

Ahmet Mustafa Kangal, Oğuzhan Şahan, Teoman Efe Aycan, Görkem Egemen Güloğlu, Halil Ersin Söken, Ali Emre Turgut, Uluç Saranlı, Mustafa Mert Ankaralı

cs.RO ·submitted 2026-11-02 10:11 UTC · v1
unusual

Abstract

Reliable separation mechanisms are critical for planetary micro-rovers, which must withstand launch vibrations and then eject the vehicle clear of the lander. This paper presents the design, optimization, and testing of the separation system of the CHERI (Challenging Environment Exploration Rovers for Intelligence) lunar micro-rovers. Sized for a 5 kg vehicle, the assembly comprises an aluminum ground plate, a central non-explosive hold-down and release mechanism, and an asymmetric four-spring ejection array. Initial separation trials revealed a velocity deficit caused by energy absorption in the flexible wheel-legs and chassis during the ejection stroke. This loss was represented as equivalent chassis damping in a multi-body dynamic model, and the springs were re-optimized accordingly. Early hardware iterations failed vibration testing, first through spring jamming in the guide housings and then through a 34 Hz fundamental mode of the flat ground plate. A density-based topology optimization raised the fundamental frequency to 84 Hz, above the 70 Hz requirement of the lander, within a 1.6 kg mass budget. The final configuration passed acceptance-level sinusoidal vibration, random vibration, and shock testing without structural degradation. Separation tests with a weight-matched one-sixth mass model, tracked by optical motion capture, confirmed clearance of the lander and reproduced the simulated free flight to within the run-to-run variation of the measured ejection velocity. These tests further showed that landing outcome is dominated by touchdown and settling dynamics, indicating that the residual pitch rate is the main controllable design parameter and confirming self-righting recovery as an integral element of the deployment architecture.

Comment
21 pages, 15 figures, journal paper

Closest papers

Nearest neighbours by meaning across the whole index.

Design and implementation of thermal control strategy for micro-size lunar exploration rover hakuto

cs.RO ·2026-10-20 ·Toshiki Tanaka, Takuto Oikawa, Keeni Shruti, Teruhito Iida, Kazuya Yoshida +1 more
unusualhighly cited similarity 0.51
Abstract · 69th International Astronautical Congress (IAC), Bremen, Germany, 1-5 October 2018

The research focuses on the thermal interface design of the HAKUTO Rover Flight Model (FM) and its evaluation using the final thermal vacuum experiment. Initially, an analytical thermal model was developed, dividing the rover into six distinct radiating surfaces. The surface temperature of the rover was then determined based on its orientation relative to the solar radiative flux, as well as other thermal factors such as lunar radiation, solar albedo, and conduction from the lunar regolith. By considering the impact of these heat sources, suitable mounting locations for the avionics and the angle of the solar panels were determined to optimize the rover's thermal performance and power generation while ensuring the rover's mass remained under 4 kg. After the preliminary thermal analysis, numerical computational simulations were conducted to further elaborate on the thermal response of the final HAKUTO Rover FM design, which was then verified through a thermal balance test in a vacuum environment.

0.55

Integrated Design and Reproducible Feasibility Analysis of a Four-Wheel Rover with Packet-Commanded Imaging, LiDAR Ranging, and Learning-Assisted Target Recognition

cs.RO ·2026-10-27 ·Sabik Bin Sultan, Shafi Bin Sultan, Safwan Sadad, Aranya Abeer Khan Prapya, Maria Sultan
benchmark similarity 0.49
Abstract · Research Manuscript for NASA HERC 2027

This study develops an integrated, reproducible design assessment for a four-wheel educational rover intended for the high-school remote-control division of the 2027 NASA Human Exploration Rover Challenge. The architecture combines commercial differential drive control, independently sprung wheel carriers, separate drive and task batteries, and a Raspberry Pi-based subsystem that executes received imaging and ranging commands. The analysis reconciles component lists with dimensioned computer-aided design views, derives mobility and electrical constraints, and connects sensor geometry to command execution. At the estimated mass of 10.919 kg, a 215 mm wheel rotating at 200 RPM produces a theoretical rolling speed of 8.105 km/h; consequently, the nominal motor label does not establish compliance with an 8 km/h design ceiling. A steady 20-degree climb requires at least 1.255 newton-meters per wheel under an assumed rolling-resistance coefficient of 0.10 and equal torque sharing. At 50 ft, an ideal 12-inch feature spans approximately 71 pixels across a full-resolution Camera Module 3 Standard image, while a 1-degree pointing error displaces the ranging ray by approximately 266 mm. An executed synthetic benchmark compares color-geometry rules and two linear support-vector classifiers on 2,400 generated board crops with scene-disjoint evaluation. A separate reference command executor is checked using mocked hardware. These software results and analytical sensitivities support a testable development plan; the study does not report physical rover trials. The principal contribution is a traceable connection between component choices, failure mechanisms, quantitative design limits, and reproducible verification tasks.

0.18

Robot-Assisted Deployment and Maintenance of Inflatable Modules for Lunar Habitation: A Field Demonstration

cs.RO ·2026-09-28 ·Kentaro Uno, Shamistan Karimov, Ashutosh Mishra, Elian Neppel, Hazal Gozbasi +3 more
published similarity 0.49
Abstract · Author's version of a manuscript accepted at the International Conference on Space Robotics 2026 (iSpaRo 2026). (c) IEEE

Long-term human habitation and in-situ development on the Moon open a new era of space utilization. In this context, robots are a key technology for facilitating the construction of future human outposts. Toward the deployment and establishment of human habitation modules on the lunar surface, we propose a combined system consisting of inflatable modules and a modular, reconfigurable robotic system. This paper presents a report demonstrating various robot-assisted task executions using real hardware, namely the modular and reconfigurable robot MoonBot and the inflatable module HIDAS, to enhance the reliability of their deployment and maintenance. The demonstrated tasks include robotic inspection during inflation, module position alignment, final safety locking, and three-dimensional mapping for post-deployment maintenance. All demonstrations were conducted either in a laboratory environment or at a lunar analogue test site. Finally, lessons learned are discussed to provide essential insights for this robotic application to future lunar habitation.

0.34

Path-Following Control and Terramechanics Analysis for Planetary Rovers Under Wheel-to-Wheel Traction Asymmetry

cs.RO ·2026-09-30 ·Ryuya Matsuoka, Keisuke Takehana, Kentaro Uno, Toshinori Kuwahara, Kazuya Yoshida
published similarity 0.48
Abstract · Author's version of a manuscript accepted at the International Conference on Space Robotics 2026 (iSpaRo 2026). (c) IEEE

This paper proposes a control strategy for path following that is model-free and relies solely on deceleration for skid-steering planetary rovers navigating deformable loose terrain under continuously imposed traction asymmetry. While conventional controllers that are based on kinematics frequently cause slip-sinkage entrapment by accelerating the wheels during path correction, the proposed approach prevents this failure by setting an upper limit on the maximum commanded velocity. Heading correction is achieved solely through the selective deceleration of the outer wheels, which are located on the outside of the turn, driving them into a negative slip regime to act as a mechanical anchor. The system was evaluated using the four-wheel independent-drive rover EX1 under an asymmetric wheel configuration with different left and right grouser heights that induces significant deviations from the path. Experimental results demonstrate that this deceleration-only control successfully suppresses accumulated lateral drift across various velocity regimes up to 0.7 m/s without causing sinkage. Crucially, direct force measurements from onboard multi-axis sensors provide important empirical evidence of the underlying terramechanics, proving that the targeted deceleration establishes dynamic load equalization across the chassis and completely restores the native thrust capability of the opposite driving wheel.

0.37

Enabling Tidying Tasks in Robotic Vacuum Cleaners via a Geometry-Induced Self-Locking Deployable Linkage

cs.RO eess.SY ·2026-10-14 ·Eunseok Song, Jinwoong Kim, Sohee Lim, Taehyeong Kim, Yongkook Kim +3 more
similarity 0.46
Abstract · 8 pages, 6 figures, 1 table. v2: corrected author name, added minor revisions

Robotic vacuum cleaners must extend their functionality within tight limits on size, cost, and durability. Deployable linkages with few actuators meet these limits, but their backdrivability makes it difficult to hold a load-bearing posture without continuous motor torque. We introduce a two-stage deployable linkage that locks through its own geometry. At full deployment, an internal three-link subchain approaches a collinear, near-singular configuration in which the input-output transmission ratio tends to zero; plate loads therefore leave only a small residual back-driving torque, which drive-train friction and a lightweight magnetic detent absorb. A single actuator performs deployment and locking, a passive chassis-mounted trigger releases the lock for retraction, and a second actuator adjusts only the deployment height. We integrate the mechanism into a commercial robotic vacuum cleaner and validate it through a 100-cycle repeatability test, a quasi-static load test in which the locked plate held 50 N with the motor de-energized, and 140 pushing-type tidying trials on seven household objects against a commercial arm-equipped vacuum robot. We derive the analytical holding condition and discuss its limits as an intermediate design point between passive compliance and articulated manipulation.

0.24

A Bi-level Co-design Framework for Lunar Monoped with 2D Jump and Landing Control

cs.RO eess.SY ·2026-10-27 ·Sanjay Ramkumar, Suraj Kumar
similarity 0.45
Abstract · 8 pages, 13 figures

Legged robots for lunar exploration must be designed for low gravity, where reduced contact forces and long flight phases make leg morphology and controller choice interdependent. We study this for a planar monoped in lunar gravity ($1.625$ m/s$^2$) using a bi-level co-design framework: a differential evolution outer loop searches over link lengths, and each candidate is evaluated on a vertical jump by either a quadratic program based task-space controller (QP-TSC) or a direct-collocation based trajectory optimization. The two controllers yield different optimal link lengths, and trajectory optimization outperforms the QP-TSC across most of the design space, with 17% lower Cost of Transport (COT) at their respective optima. We then extend to a 2D jump, where trajectory optimization with centroidal angular momentum regulation produces stable in-place and forward jumps, and an LQR controller absorbs impact and stabilizes the robot after touchdown. This is demonstrated on a baseline morphology with both links 0.3 m long.

0.17

Designing an Efficient Excavator Bucket for Lunar ISRU: A Comparative Study with Vision-Based Fill and Displacement Analysis

cs.RO ·2026-09-22 ·Abdulla Hil Kafi, Tomoki Koshi, Jorge Casir, Kenji Nagaoka
top venue similarity 0.44
Abstract · Accepted and presentaed at the 2026 IEEE International Conference on Robotics and Automation (ICRA 2026)

This paper present a spiral-cavity wheel for lunar regolith excavation and a sensor-light evaluation stack that jointly estimates fill ratio (vision), sinkage (vision), and specific energy from actuator logs. In benchtop tests (four revolutions at 5, 10, and 15~RPM) against two literature baselines, the proposed wheel achieved higher excavated mass and fill ratio, delivering 2.2-3.0 times higher excavation rate while reducing specific energy by 29 % relative to a bucket-drum baseline. Normalized sinkage (mm/kg) was also lower, indicating stable traction without bogging. Effort-time traces show a steady torque envelope with repeatable cut-carry-dump cycles across speeds. We provide a retention index $η$ that correlates with fill ratio and a DEM setup that reproduces experimental trends with low error. Results suggest spiral-cavity wheels can replace heavier multi-actuator diggers when mass, simplicity, and energy efficiency are mission drivers.

0.45

Toward Lunar Legged Robots: Field Deployment Lessons at LUNA

cs.RO ·2026-10-08 ·Adrian Fuhrer, Joseph Church, Oliver Fischer, William Talbot, Nicolas Faesch +4 more
similarity 0.43
Abstract · Proceeding to the IEEE iSparo Conference 2026

Legged robots are promising candidates for future lunar surface missions because they can traverse steep, loose, and obstacle-rich terrain that challenges conventional wheeled rovers. However, readiness for lunar deployment is limited by uncertainties in foot-regolith interaction, dust generation, illumination-driven perception degradation, and operational constraints. This paper reports lessons from the 2025 LUNA analogue campaign, where ANYmal-D and Magnecko traversed loose regolith simulant and crater-like terrain and collected long-horizon navigation and visual-inertial data under challenging lighting. We show that quadrupedal robots can traverse regolith simulant, but performance is affected by sinkage and slip, dust-generating contacts, and perception failures caused by overexposure, shadows, and low-texture regions. These results motivate tighter integration of regolith-aware locomotion policies, illumination-robust perception, repeatable analogue testing, and mission-level operational validation for future lunar legged robots.

0.22